Shure FP24 manual Limited Two-year Warranty, Certification, FCC Declaration of Conformity

NOTE: When interconnecting the FP24 and FP33, inputs from the FP24 appear at the FP33 mixbus with their polarity reversed. (This is unavoidable due to the nature of the interconnection.) To avoid cancellation or interference effects (e.g., comb filtering) be- tween the signals from the FP24 and FP33 inputs, use Shure A15PRS polarity inverters on the FP24 inputs, or do one of the fol- lowing:

•Keep microphones connected to the FP24 as far away as possible from those connected to the FP33.

•For microphones that must be close together (such as those in a stereo pair), connect them to the same mixer.

NOTE: If constructing your own FP24/FP33 interconnect cable:

•Keep cable length to a minimum, since the interconnection is unbalanced.

•Be sure to drive the FP33 mix bus off of pin 2 of the FP24 since the FP24 inputs are reverse polarity with respect to FP33 inputs.

FP24 XLR±L 820 ohm FP33 mixbus

FP24 XLR±R

820 ohm

This class B digital apparatus complies with Canadian ICES±003. Eligible to bear CE marking.

Conforms to European EMC directive 89/336/EEC: Professional Audio Products Standard EN 55103 (1996); Part 1 (emissions) and Part 2 (immunity). The FP24 is intended for use in environments E1 (residential) and E2 (light industrial) as defined in European EMC standard EN 55103. It meets the applicable tests and performance criteria found in the standard for these environments. EMC conformance is based on the use of shielded interconnecting cables.

N 108

Limited Two-year Warranty

Shure Incorporated (ªShureº) hereby warrants that this product will be free from de- fects in materials and workmanship for a period of two years from date of purchase.

At its option Shure will repair or replace the defective product and promptly return it to you, or refund the purchase price. You should retain proof of purchase to validate the purchase date and return it with any warranty claim.

If you believe this product is defective within the warranty period, carefully repack the unit, insure it, and return it postage prepaid to:

Shure Incorporated

Attention: Service Department 5800 W. Touhy Avenue

Evanston, Illinois 60714–4608 U.S.A.

Outside the United States, return the product to your dealer or Authorized Service Center.

This warranty does not apply in cases of abuse or misuse of the product, use con- trary to Shure's instruction, or unauthorized repair. All implied WARRANTIES OF MER- CHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE are hereby disclaimed and Shure hereby disclaims liability for incidental, special, or consequential damages resulting from the use or unavailability of this product.

Some states do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of incidental or consequential damages, so the above limitation may not apply to you. This warranty gives you specific legal rights, and you may have other rights which vary from state to state.

Figure 4. FP24/FP33 Mix Bus Interconnect Cable

Positive: Solder to center pin

(marked with a white stripe on PS20 cable)

Negative: Solder to sleeve

Figure 5. Attaching the Supplied Threaded Power

Connector.

Certification

Authorized under the DECLARATION OF CONFORMITY provision of FCC part 15 as a Class B digital device. Tested to comply with FCC standards. FOR HOME OR OFFICE USE. This product complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by Shure Incorporated could void your authority to operate this equipment.

This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

￿Reorient or relocate the receiving antenna

￿Increase the separation between the equipment and the receiver

￿Connect the equipment into an outlet on a circuit different from that to which the receiver is connected

￿Consult the dealer or an experienced radio/TV technician for help

FCC Declaration of Conformity

We of

Shure Incorporated

5800 W. Touhy Avenue Evanston IL 60714±4608 U.S.A. 847±600±2000

declare under our sole responsibility that the following product,

Model: FP24 Name: FP24 Microphone mixer/preamplifier

was tested and found to comply with Part 15 of the FCC rules.

Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, includ- ing interference that may cause undesired operation.

Testing was completed by the following NVLAP or A2LA accredited laboratory:

L.S. Compliance, Inc.

W66 N220 Commerce Court

Cedarburg, Wisconsin 53012

Telephone 262±375±4400

Fax 262±375±4248

Shure Incorporated, Manufacturer.

Signed: Date: Sept. 15, 2000

Name, Title: Craig Kozokar, Project Engineer, EMC

SHURE Incorporated Web Address: http://www.shure.com 5800 W. Touhy Avenue, Niles, IL 60714-4608, U.S.A.

In U.S.A., Phone: 1-847-600-2000 Fax: 1-847-600-1212

In Europe, Phone: 49-7131-72140 Fax: 49-7131-721414

In Asia, Phone: 1-852-2893-4290 Fax: 1-852-2893-4055

6International Fax: 1-847-600-6446