Wiring Connections, Mounting, Furnished Accessories

Shock Mount

Internal rubber vibration isolator

Cable

1.8m (6 ft) cable with effective hum shielding, four conductors (two shielded), plastic jacketed

Case

Black finish die casting with black enamel diecast grille and stainless steel screen

DIMENSIONS (FIGURE 3)

1.8 m

6 ft

16.5cm

6.5 in.

2 cm

3.75 cm0.85 in.

1.5 in.

OVERALL DIMENSIONS

FIGURE 3

Net Weight

315 grams (11.1 oz)

CERTIFICATION

Conforms to European Union directives, eligible to bear CE marking; meets European Union EMC Immunity Requirements (EN 50 082-1, 1992).

WIRING CONNECTIONS

The RED and BLACK cable leads are the microphone audio conductors for balanced-line connections; the shield is connected to the amplifier ground. The GREEN and WHITE leads control an external relay or switching circuit. Refer to the following table and the wiring diagram in Figure 4.

INPUT TYPE	WIRE	FUNCTION	XLR	1/4 IN.
	COLOR		CONNECTOR	PHONE
				PLUG
	RED	AUDIO	PIN 2	TIP

UNBALANCED	BLACK	AUDIO GROUND	PIN 3	SLEEVE
	SHIELD	CHASSIS GROUND	PIN 1	SLEEVE

	RED	AUDIO +	PIN 2	TIP

BALANCED	BLACK	AUDIO -	PIN 3	RING
	SHIELD	CHASSIS GROUND	PIN 1	SLEEVE

SHIELD

SWITCH SHOWN IN ”OFF” POSITION

INTERNAL CONNECTIONS

FIGURE 4

MOUNTING

To mount the microphone on a gooseneck or fixed pipe with a

5-8 in. 27 mounting thread, proceed as follows:

1.Use the supplied hex wrench to loosen the setscrew enough so that the end cap can be unscrewed from the microphone.

2.Remove the end cap from the microphone.

3.Remove the thin metal washer and the metal spacer.

4.Replace the washer by sliding it on to the cable and up into the end of the microphone.

5.Slip the cable through the gooseneck or pipe.

6.Thread the microphone firmly onto the end of the gooseneck or pipe.

7.Tighten the setscrew to prevent the microphone from loosen- ing.

FURNISHED ACCESSORIES

1.27 mm (.050 mm) Hex Wrench. . . . . . . . . . . . . 80A67

REPLACEMENT PARTS

Cartridge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . R180 Grille Assembly . . . . . . . . . . . . . . . . . . . . . . . . .RK334G Cable, 1.8 m (6 ft) . . . . . . . . . . . . . . . . . . . . . . 70A4172

OPTIONAL ACCESSORIES

Black Gooseneck, 0.3 m (12 in.) . . . . . . . . . . . . . G12B Black Heavy-duty Mounting Flange. . . . . . . . . A13HDB Windscreen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A1WS Black Mounting Flange. . . . . . . . . . . . . . . . . . . . . . A12B

For additional service or parts information, please contact Shure's Service department at 1-847-600-8699. Outside the United States, please contact your authorized Shure Service Center.

SHURE Incorporated http://www.shure.com United States, Canada, Latin America, Caribbean: 5800 W. Touhy Avenue, Niles, IL 60714-4608, U.S.A.

Phone: 847-600-2000 U.S. Fax: 847-600-1212 Intl Fax: 847-600-6446 Europe, Middle East, Africa:

Shure Europe GmbH, Phone: 49-7131-72140 Fax: 49-7131-721414 Asia, Pacific:

Shure Asia Limited, Phone: 852-2893-4290 Fax: 852-2893-4055