Gemini Industries Introduction, FCC Rules and Regulations, UX-1600 Wireless System

Introduction

Congratulations on your purchase of a Gemini wireless system. This-state- of-the-art unit includes all the latest features backed by a three year limited warranty. Prior to use, we suggest that you carefully read the instructions.

Cautions

1.All operating instructions should be read before using this equipment.

2.To reduce the risk of electrical shock, do not open the unit. THERE ARE NO USER REPLACEABLE PARTS INSIDE. Please refer servicing to a qualified service technician.

3.Do not expose this unit to direct sunlight or to a heat source such as a radiator or stove.

4.Dust, dirt and debris can interfere with the performance of this unit. Make an effort to keep the unit away from dusty, dirty environments, and cover the unit when it is not in use. Dust it regularly with a soft, clean brush.

5.When moving this equipment, it should be placed in its original carton and packaging. This will reduce the risk of damage during transit.

6.DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.

7.DO NOT USE ANY SPRAY CLEANER OR LUBRICANT ON ANY CONTROLS OR SWITCHES.

FCC Rules and Regulations

Gemini wireless systems are the type accepted under FCC rules parts 74 and 15. Licensing of Gemini equipment is the user’s responsibility and licensability depends on the user’s classification and application.

Note

This equipment has been tested and found to comply with the limits set forth under part 15 and 74 of FCC rules. This equipment operates at a frequency that has been authorized by the FCC. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio or television reception, try one or more of the following suggestions:

1.Change the frequency you are using to another one of the 16 selectable frequencies. See the instructions for selecting frequencies for more information.

2.Repoint or relocate the receiving antenna.

3.Plug the equipment into a socket on a different circuit.

Remember, any changes made to the unit without authorization from Gemini will void your warranty.

UX-1600 Wireless System

The UX-1600 wireless system is a high quality audio product that provides excellent performance under most operating conditions.

The different systems available all operate on a UHF high band frequency between 790.375 MHZ to 805.375 MHZ.

The systems available are:

UX-1600M- equipped with UM-68hand held microphone transmitter.

UX-1600L- equipped with UB-68Lbelt pack transmitter w/ lavalier mic. UX-1600H- equipped with UB-68Hbelt pack transmitter w/ headset mic.

2.The UX-1600 has 16 selectable frequencies so that you can choose the one with the least amount of interference. The illustration shows the dip switch settings for the 16 frequencies.

Set the dip switches on the receiver and those on the belt pack transmitter or hand held mic transmitter to matching frequencies. Dip switches for the receiver are located on the front panel. Dip switches for the belt pack transmitter are located on the side of the belt pack. The dip switches for the hand held mic may be accessed by opening the battery holder on the side of the mic.

3.Plug the AC adapter into the rear of the receiver where the jack is labeled DC 12-18V. Then plug the adapter into an appropriate AC outlet. Note: The adapter is available in 120V AC or 230V AC.

4.The receiver is supplied with 2 output jacks. The UNBALANCED OUTPUT is used to connect the receiver to your amp, effects or mixer mic jack using a standard mic cable with a 1/4” connector. The BAL- ANCED OUTPUT is used to connect the receiver to your amp, effects or mixer mic jack using a standard mic cable with a XLR connector. We recommend using the balanced output if the cable to your amp, effects or mixer mic jack is 10 feet or more. The BALANCED OUTPUT has three separate conductors, two of which are signal (positive and negative) and one shield (ground). Pin 1 is ground (shield). Pin 2 is signal hot (positive). Pin 3 is signal cold (negative).

5.Point the antenna upward. Switch the power to the ON position.

6.Adjust the volume using the LEVEL control on the front panel.

7.Adjusting the squelch on the receiver can eliminate such problems as bleeding that occurs from using several systems at the same time or interference from local television. To adjust the squelch, place the small plastic tool (included with the unit) in the hole marked SQUELCH at the back of the unit, and slowly turn the tool to adjust the output level to just above the level of background noise. Setting the squelch too high will reduce the range of the system. Setting the squelch too low will increase the level of unwanted noise.

Hand Held Transmitter Features

•High sensitivity cardioid capsule for professional use.

•Special noise absorption material inside the mic barrel eliminates switch shock and handling noise.

UX-1600 Receiver Operation

1.Remove all packing materials. Save the box and packing material to transport the unit in the unlikely event the unit requires service.

Cautions

1.Do not drop the microphone element or strike it with your fist or fingers. Do not blow into the microphone head front to “check it.”

2.Do not use the microphone in areas of high humidity or high temperature as this could damage of the microphone.

USA Page 2 USA