TOA Electronics M-9000 manual Specifications are subject to change without notice

T-001TDual Line Output Expansion Module with DSP

The T-001T is a plug-in module designed for use with the M-9000 and provide two independent balanced outputs. It can drive load of 600Ω up to +16dB. It can process effect for TONE/EQ/ COMPRESSOR to two inputs independently.

Power Source	+24 V DC, -24 V DC, +6 V DC
Current Consumption	35 mA (at +24 V DC), 35 mA (at -24 V DC), 60 mA (at +6 V DC)
Output	2 channels, max. +20 dB* (at 10 kΩ load), 600 Ω,
	electronically-balanced, removable terminal block (3 pins)
Frequency Response	20-20,000 Hz, +1, -3 dB
Total Harmonic Distortion + N	0.005% (at 1 kHz, 20 – 20,000 Hz BPF, 5 V output, 10 kΩ load)
S/N Ratio	Over 73 dB (at 20 – 20,000 Hz BPF )
Residual Noise	Under -91 dB (at 20 – 20,000 Hz BPF, VOL: -70 dB)
Crosstalk	Over 87 dB (at 20 kHz)
D/A Converter	24 bit ∆∑DAC
Sampling Frequency	48 kHz
Tone Control	Bass: ±12 dB (at 100 Hz), Treble: ±12 dB (at 10 kHz)
Parametric Equalizer	10 bands, Frequency: 20-20,000 Hz, 31 steps,
	Variable range: ±12 dB, Q: 0.3-5
Speaker Equalizer	15 (compatible with TOA speakers only)
High-pass Filter	-12 dB/oct, Variable frequency range: 20 – 400 Hz, 14 steps
Low-pass Filter	-12 dB/oct, Variable frequency range: 4,000 – 20,000 Hz, 8 steps
Compressor	Depth: 1-5
Delay	0-40 ms (1 ms step), maximum 40 ms (CH 1 + CH2), mixer mode only
Operating Temperature	-10°C to +40°C
Finish	Panel: Aluminum, hair-line
Dimensions	35 (W) ⋅ 78 (H) ⋅ 91.5 (D) mm
Weight	82 g
Accessory	Removable terminal plug (3 pins) ⋅ 2, Module mounting screw ⋅ 2
*0 dB = 1 V

C-001TInput/OutputModule Control

The C-001T is Control I/O expansion module designed for use with the M-9000 and can provide up to 8 channels each of input and output expansion. Since the main unit has 4 preinstalled inputs and outputs each, the control input and output can be expanded to up to 12 channels each when the C-001T is used.

Power Source	6 V DC
Current Consumption	15 mA
Control Input	8 channels, open voltage: 3.3 V DC, short-circuit
	current: under 1 mA, removable terminal block (9 pins)
Control Output	8 channels, open collector output, withstand voltage: 27 V DC,
	control current: max. 50 mA, removable terminal block (9 pins)
Operating Temperature	-10°C to +40°C
Finish	Panal: Aluminum, hair-line
Dimensions	35 (W) ⋅ 78 (H) ⋅ 91.5 (D) mm
Weight	62 g
Accessory	Removable terminal plug (9 pins) ⋅ 2, Module mounting screw ⋅ 2

ZP-001TTelephone Zone Paging Module

The ZP-001T is a zone paging module designed for use with the M-9000 and functions as interface to connect the M-9000 to an analog PABX, allowing zone paging to be initiated from the PABX. There are two operation modes: ring signal and paging port modes.

Broadcast can be initiated regardless of operation mode.

Power Source	+24 V DC, +6 V DC
Current Consumption	38 mA (at +24 V DC), 18 mA (at +6 V DC)
Number of Line	1 line
Type of Selectable Signal	DTMF signal
Signaling System	Loop-Start (or Ground-Start, selectable)
TEL Line	0 dB, 600 Ω, balanced, transformer-isolated, loop voltage:
	24 V DC or more which should be supplied from the PABX, RJ11 connector
Paging Input	0 dB, 600Ω, balanced, transformer-isolated audio input,
	removable terminal block (4 pins)
Control Input	1 channel, no-voltage make contact, open voltage: 5 V DC,
	short-circuit current: 0.5 mA, removable terminal block (4 pins)
Control Output	4 channels, open collector output (isolated), withstand voltage: 35 V DC,
	control current: max. 50 mA, removable terminal block (4 pins)
Operating Temperature	-10°C to +40°C
Finish	Pael: Aluminum, hair-line
Dimensions	35 (W) ⋅ 78 (H) ⋅ 91.5 (D) mm
Weight	153 g
Accessory	Removable terminal plug (4 pins) ⋅ 3, Module mounting screw ⋅ 2

D-001TDual Mic/Line Input Module with DSP

The D-001T is a plug-in module designed for use with the M-9000 and can provide two independent balanced inputs. The D-001T can handle signals ranging from microphone level to line level by controlling their input sensitivity in 9 increments from -60dB to -10dB.

Phantom power (+24V) can be supplied for condenser microphone use. The D-001T can process effect for TONE/EQ/COMPRESSOR to two inputs independently.

Power Source	+24 V DC, -24 V DC, +6 V DC
Current Consumption	20 mA (at +24 V DC), 20 mA (at -24 V DC), 60 mA (at +6 V DC)
Input	2 channels, 3 kΩ (when the phantom power is ON)/
	10 kΩ (when the phantom power is OFF),
	electronically-balanced, removable terminal block (3 pins)
Input Sensitivity	-60, -54, -48, -42, -36, -30, -24, -18, -10 dB* (selectable)
Frequency Response	20 – 20,000 Hz, +1, -3 dB
Total Harmonic Distortion + N	0.008% (at 1 kHz, 20-20,000 Hz BPF, Input sensitivity: -10 dB)
Input Equivalent Noise	Under -112 dB (at 20 – 20,000 Hz BPF, Input short, Input sensitivity: -60 dB)
S/N Ratio	Over 73 dB (at 20 – 20,000 Hz BPF, Input short, Input sensitivity: -10 dB)
Crosstalk	Over 75 dB (at 20 kHz, Input sensitivity: -10 dB)
CMRR	Over 62 dB (at 1 kHz, Input sensitivity: -60 dB)
A/D Converter	24 bit ∆∑ADC
Sampling Frequency	48 kHz
Tone Control	Bass: ±12 dB (at 100 Hz), Treble: ±12 dB (at 10 kHz)
Parametric Equalizer	10 bands, Frequency: 20 – 20,000 Hz, 31 steps,
	Variable range: ±12 dB, Q: 0.3-5
High-pass Filter	-12 dB/oct, Variable frequency range: 20 – 400 Hz, 14 steps
Low-pass Filter	-12 dB/oct, Variable frequency range: 4,000 – 20,000 Hz, 8 steps
Compressor	Depth: 1 – 5
Phantom Power	+24 V DC
Operating Temperature	-10°C to +40°C
Finish	Panel: Aluminum, hair-line
Dimensions	35 (W) ⋅ 78 (H) ⋅ 91.5 (D) mm
Weight	82 g
Accessory	Removable terminal plug (3 pins) ⋅ 2, Module mounting screw ⋅ 2
*0 dB = 1 V

AN-001TAmbient Noise Controller Module

The AN-001T is a plug-in module of 2-channel ambient noise detector designed for use with the M-9000.

It automatically adjusts the output volume in response to the change of ambient noise level. The AN-001T can handle input signals from microphone level (-60dB) to line level (-10dB) by controlling the gain in 9 steps. Phantom power (+24V) can be supplied for condenser microphone use.

Power Source	+24 V DC, -24 V DC, +6 V DC
Current Consumption	20 mA (at +24 V DC), 20 mA (at -24 V DC), 60 mA (at +6 V DC)
Input	Sensor input (Ambient noise sensor microphone input):
	2 channels, 3 kΩ (when the phantom power is ON)/10 kΩ
	(when the phantom power is OFF), electronically-balanced,
	removable terminal block (3 pins)
Input Sensitivity	-60, -54, -48, -42, -36, -30, -24, -18, -10 dB* (selectable)
Phantom Power	+24 V DC
A/D Converter	24 bit ∆∑ADC
Sampling Frequency	48 kHz
Ambient Noise Control	Sensor input reference level adjustment function
Function	Maximum output signal level control: -15 to 0 dB
	Minimum output signal level control: -18 to -3 dB
	Sample time setting: 10 s, 15 s, 20 s, 30 s, 1 min, 2 min, 3 min, 5 min
	Gain ratio setting (Ambient noise: Output signal level):
	6:3, 5:3, 4:3, 3:3, 3:4, 3:5, 3:6, 6:-3, 5:-3, 4:-3, 3:-3, 3:-4, 3:-5, 3:-6,
Operating Temperature	-10°C to +40°C
Finish	Panel: Aluminum, hair-line
Dimensions	35 (W) ⋅ 78 (H) ⋅ 91.5 (D) mm
Weight	82 g
Accessory	Removable terminal plug (3 pins) ⋅ 2, Module mounting screw ⋅ 2
Option	Ceiling mount microphone: AN-9001
*0 dB = 1 V

TOA Corporation

http://www.toa.jp

Specifications are subject to change without notice.

Printed in Japan (0612) 833-52-377-40 u