CONTROLS: (CONTINUED)
13 CHANNEL ROTARY GAIN
The CHANNEL ROTARY GAIN allows you to boost the signal of each individual channel depending on how low or high its input level is
14 3 BAND EQUALIZER
The 3 BAND EQUALIZER adjust the tone of each CHANNEL by giv- ing you a choice 3 frequencies (BANDS) to adjust , from LOW, MIDRANGE (MID) and HIGH’s ,you can use the adjustment knobs to higher or lower the 3 separate frequencies till the sound of the music program is appropriate for your listening environment.
15 CHANNEL VOLUME FADER
After you have chosen which input you will use with the INPUT SE- LECTOR the corresponding CHANNEL FADER will allow you to ad- just the volume for that particular CHANNEL.
16 FADER ADJUSTMENT SWITCHES
The fader adjustment switches allow you to change the functionality of the fader. The REVERSE switch when in the ON position will flip the fader so it works in REVERSE ie. channel (1) on the left and chan- nel (2) on the right. The CURVE selector lets you choose between two fader CURVE settings, positioning the switch to the left will give you a gradual CROSSFADE and positioning the switch to the right will give you a quick CROSSFADE.
17 CROSS FADER
The CROSS FADER allows you to mix evenly from one source to an- other. On the
NOTE: WHEN USING THE CROSS FADER LIGHTLY GLIDE THE FADER BACK AND FORTH. PRESSING DOWN ON THE CON- TROLS CAN BEND CONTACTS AND CAUSE A LOSS OF SOUND.
18 VU METER
The
19 CUE MASTER SWITCH
The VU METER has two display modes, in CUE mode it will display the level of the channel you are cueing, in MASTER mode it displays the main MASTER output.
20 MASTER VOLUME ROTARY
The MASTER VOLUME ROTARY knob adjust the volume of the MAIN output
21 CUE/PGM ROTARY
The CUE/PGM ROTARY determines the mix between the chosen CHANNEL CUE SELECTOR and the MAIN OUTPUT mix.
22 CUE VOLUME ROTARY KNOB
The CUE VOLUME ROTARY KNOB adjusts your HEADPHONE MONITOR OUTPUT’S volume.
1923 CHANNEL CUE SELECTOR
The CHANNEL CUE SELECTOR allows you to choose which chan- nel you wish to monitor in your headphones.
PS-626USB
USB SETUP:
ON A PC
Open the START menu and go to CONTROL PANEL, once in the control panel folder click on the SOUND AND AUDIO DEVICES ICON, when the SOUND AND AUDIO DEVICES window opens click on the AUDIO pane, then under SOUND PLAYBACK choose the USB AUDIO CODEC as a DEFAULT DEVICE,then you just click on APPLY and you are ready to use the
ON A MAC
Under the APPLE menu open SYSTEM PREFERENCES, and in SYSTEM PREFERENCES choose the SOUND icon, once in the SOUND window choose the OUTPUT pane and under CHOOSE A DEVICE FOR SOUND OUTPUT select USB AUDIO CODEC. Repeat the procedure for the INPUT pane, now your MAC is ready to work with the
FADER REPLACEMENT:
1.UNSCREW THE FADER (B) SCREWS. DO NOT TOUCH INSIDE SCREWS (C) CAREFULLY RE- MOVE OLD CROSS FADER AND UNPLUG CABLE (D)
2.PLUG IN THE NEW CROSS FADER INTO CABLE (D) AND PLACE BACK INTO MIXER.
3.SCREW THE CROSS FADER TO MIXER WITH THE FADER PLATE SCREWS (B)
4.REPLACE THE FACE OF THE MIXER AND SCREW THE FOUR SCREWS BACK IN AND REPLACE THE FADER KNOBS.
SPECIFICATIONS:
INPUTS:
Phono | ............................................................................3mV,47 K Ohm |
Line | 150 mV, 27 K Ohm |
MIC | 1.5 mV, 1 KOhm Balanced |
OUTPUTS:
Max | 20V |
Rec | 225 mV, 5 K Ohm |
GENERAL:
Frequency Response | 20Hz - 20KHz +/- 2dB |
Distortion | < 0.02% |
S/N Ratio | Better than 85 dB |
Headphone impedance | 8 Ohm |
Power Source | AC 15v 500mA |
Unit dimensions | 10” x 3.3” x 12” |
............................................................................. | (254 x 84 x 304 mm) |
Weight | 6.5 lbs (2.94 kg) |
SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTIFICATION FOR IMPROVE- MENT
5