Texas Instruments THS4012 specification

General High-Speed Amplifier Design Considerations

1.11 General High-Speed Amplifier Design Considerations

The THS4012 EVM layout has been designed and optimized for use with high-speed signals and can be used as an example when designing THS4012 applications. Careful attention has been given to component selection, grounding, power supply bypassing, and signal path layout. Disregard of these basic design considerations could result in less than optimum performance of the THS4012 high-speed, low-power operational amplifier.

Surface-mount components were selected because of the extremely low lead inductance associated with this technology. Also, because surface-mount components are physically small, the layout can be very compact. This helps minimize both stray inductance and capacitance.

Tantalum power supply bypass capacitors (C1 and C2) at the power input pads help supply currents for rapid, large signal changes at the amplifier output. The

0.1μF power supply bypass capacitors (C4 and C5) were placed as close as possible to the IC power input pins in order to keep the PCB trace inductance to a minimum. This improves high-frequency bypassing and reduces harmonic distortion.

A proper ground plane on both sides of the PCB should always be used with high-speed circuit design. This provides low-inductive ground connections for return current paths. In the area of the amplifier IC input pins, however, the ground plane was removed to minimize stray capacitance and reduce ground plane noise coupling into these pins. This is especially important for the inverting pin while the amplifier is operating in the noninverting mode. Because the voltage at this pin swings directly with the noninverting input voltage, any stray capacitance would allow currents to flow into the ground plane, causing possible gain error and/or oscillation. Capacitance variations at the amplifier IC input pin of less than 1 pF can significantly affect the response of the amplifier.

In general, it is always best to keep signal lines as short and as straight as possible. Round corners or a series of 45_bends should be used instead of sharp 90_ corners. Stripline techniques should also be incorporated when signal lines are greater than 1 inch in length. These traces should be designed with a characteristic impedance of either 50 Ω or 75 Ω, as required by the application. Such signal lines should also be properly terminated with an appropriate resistor.

Finally, proper termination of all inputs and outputs should be incorporated into the layout. Unterminated lines, such as coaxial cable, can appear to be a reactive load to the amplifier IC. By terminating a transmission line with its characteristic impedance, the amplifier's load then appears to be purely resistive and reflections are absorbed at each end of the line. Another advantage of using an output termination resistor is that capacitive loads are isolated from the amplifier output. This isolation helps minimize the reduction in amplifier phase-margin and improves the amplifier stability for improved performance such as reduced peaking and settling times.

1-16

General

THS4012 specifications

The Texas Instruments THS4012 is a high-performance, dual-channel operational amplifier designed for a wide variety of applications requiring high speed and precision. This op-amp is particularly appreciated in the fields of signal processing, data acquisition, and instrumentation, thanks to its exceptional characteristics and innovative technologies.

One of the standout features of the THS4012 is its ultra-low input noise and high slew rate, which make it a compelling choice for applications that demand rapid response times without signal distortion. With a slew rate of up to 1200 V/µs, the THS4012 can handle rapid changes in input signals, making it ideal for high-frequency applications such as analog-to-digital converters and RF signal processing.

In terms of performance, the THS4012 boasts a wide bandwidth of approximately 100 MHz at a gain of 1, ensuring it can efficiently transmit fast signals without significant loss. The part also provides a high common-mode rejection ratio (CMRR) and power supply rejection ratio (PSRR), enhancing its stability in environments with fluctuating power supply conditions or varying signal levels.

Another important aspect of the THS4012 is its low total harmonic distortion (THD), which is crucial for high-fidelity applications. By minimizing distortions, it ensures that the output signal closely matches the input signal, preserving the integrity of the original waveform. This makes it especially suitable for audio applications and precision data acquisition systems.

The THS4012 operates on a single or dual power supply, with a voltage range from ±2.5 V to ±6 V, providing designers with the flexibility to integrate this op-amp into various circuit configurations. The device is available in compact packages, making it suitable for space-constrained designs in portable electronics.

Additionally, the THS4012 incorporates innovative features such as internal compensation, which simplifies the design process by reducing the need for external components. This enhances design efficiency and reliability, allowing engineers to focus on other critical aspects of their circuits.

In conclusion, the Texas Instruments THS4012 dual operational amplifier combines high-speed performance, low distortion, and flexible power supply options, making it a popular choice for engineers looking to enhance the capabilities of their electronic systems. Its advanced technologies and characteristics render it a strong option in a myriad of applications within today's demanding electronic landscape.