Peavey 400 ONE-YEAR Limited WARRANTY/REMEDY, Peavey OO-DAY Limited Warranty on Tubes and Meters

Page 5

NASHVILLE’” 400 SPECS

POWER AMPLIFIER SECTION:

RATED POWER & LOAD:

210 W RMS into 4 ohms

with DDTgcompression and LED indicator

POWER @ CLIPPING: (TYPICALLY) (5% THD, 1 KHz, 120 VAC line)

130 W RMS tino 8 ohms

220 W RMS into 4 ohms

2 ohms not recommended

FREQUENCY RESPONSE:

+O, -1 dB, 20 Hz to 20 KHz @ 200 W RMS into 4 ohms

TOTAL HARMONIC DISTORTION:

Less than 0.2O/6, 1OOmW to 200 W RMS,

20 Hz to 10 KHz, 4 ohms, typically below 0.1%

DDT@ DYNAMIC RANGE:

Greater than 20 dB

DDT@ MAXIMUM THD:

Below 0.5% THD for 6 dB overload

Below 1% THD for 20 dB overload

HUM & NOISE:

Greater than 95 dB below rated power

POWER CONSUMPTION: (DOMESTIC)

600 watts, 50/60 Hz, 120 VAC

POWER SECTION:

THE FOLLOWING SPECS ARE MEASURED @ 1 KHz

WITH THE CONTROLS PRESET AS FOLLOWS:

PRE GAIN PULL BRIGHT OFF (IN) POST GAIN @ 10

LOW EQ @ +6 dB MID EQ @ -9 dB SHIFT @ 300 Hz HIGH EQ @ +3 dB PRESENCE EQ @ +6 dB REVERB @ 0

NOMINAL LEVELS ARE WITH PRE GAIN @ 5 MINIMUM LEVELS ARE WITH PRE GAIN @ 10

PREAMP HIGH GAIN INPUT: (NO PAD)

Impedance: High Z, 220K ohms

Nominal Input Level: -28 dBV, 40 mV RMS

Minimum Input Level: -46 dBV, 5 mV RMS

Maximum Input Level: +8 dBV, 2.5 V RfylS

PREAMP LOW GAIN INPUT: (-10 dB PAD) Impedance. High Z, 44K ohms

Nominal Input Level: -18 dBV, 130 mV RMS

Minimum Input Level: -36 dBV, 16 mV RMS

Maximum Input Level: +18 dBV, 8 V RMS

PATCH OUTPUT:

Function: Low Level Pre-EQ Effects/Pedal Send

Load Impedance: 1 K ohms or greater

Nominal Output: -14 dBV, 0.2 V RMS

PATCH INPUT:

Function: Low Level Pre-EQ Effects/Pedal Return ImpedanceL High Z, 220K ohms

Designed Input Level: -14 dBV, 0.2 V RMS

(Switching jack providing patch output to patch input connection when not used)

PREAMP OUTPUT:

Function: High Level Post EQ Signal Send

Load Impedance: 1 K ohms or greater

Nominal Output: 0 dBV, 1 V RMS

Maximum Output: +18 dBV, 8 V RMS

POWER AMP INPUT:

Function: High Level Post EQ Signal Return

Impedance: High Z, 22K ohms

Designed Input Level: 0 dBV, 1 V RMS

(Switching jack providing preamp output to power amp input connection when not used)

SYSTEM HUM & NOISE @ NOMINAL INPUT LEVEL: (20 Hz to 20 KHz unweighted)

75 dB below rated power

EQUALIZATION:

LOW: +-15 dB @ 60 Hz, Shelving

MID: +-I5 dB (@ Shift Frequency), Peak/Notch

SHIFT: 150 Hz to 1500 Hz

HIGH: +-15 dB @ 2 KHz (Special EQ)

PRESENCE: +-15 dB @ 5 KHz, Shelving

PULL BRIGHT: +6 dB @ 2 KHz

FOOTSWITCH:

Reverb defeat

DANGER

EXPOSURE TO EXTREMELY HIGH NOISE LEVELS MAY CAUSE A PERMANENT HEARING LOSS INDIVIDUALS VARY CONSIDERABLY IN SUSCEPTIBILITY TO NOISE INDUCED HEARING LOSS BUT NEARLY EVERYONE WILL LOSE SOME HEARING IF EXPOSED TO SUFFICIENTLY INTENSE NOISE FOR A SUFFICIENT TIME

THF II S GOVERNMENTS OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION iOSHAi HAS SPECIFIED THE FOLLOWING PERMISSIBLE NOISE LEVEL EXPOSURES

THIS LIMITED WARRANTY VALID ONLY WHEN PURCHASED AND REGISTERED IN THE UNITED STATES OR CANADA. ALL EXPORTED PRODUCTS ARE SUBJECT TO WARRANTY AND SERVICES TO BE SPECIFIED AND PROVIDED BY THE AUTHORIZED DISTRIBUTOR FOR EACH COUNTRY.

Ces clauses de garantie ne sont vaiables qu’aux Etats-Unis et au Canada. Dans tous les autres pays, les clauses de garantie et de maintenance sont lixees par le distributeur national et assuree par lul seion la legislation en vigueur.

Diese Garantie ist nur in den USA and Kanada gultig. Alle Export-Produkte sind der Garantie und dem Service des lmporteurs des jewelligen Landes unterworfen.

Esta garantia es vallda solamente cuando el product0 es comprado en E.U. continentales o en Canada. Todos 10s productos que Sean comprados en el extranjero, estan sujetos a las garantias y servicio que cada distribuidor autorizado determine y olrezca en 10s diferentes paises.

ONE-YEAR LIMITED WARRANTY/REMEDY

PEAVEY ELECTRONICS CORPORATION (“PEAVEY”) warrants this product, EXCEPT for covers, footswitches, patchcords, tubes and meters, to be free from defects inmaternal and workmanshipforaperiod of one (1) yearfromdateof purchase, PROVIDED, howeverthatthlslimlted warrantyisextended onlytotheorlglnal retall purchaserand issubjecttothe conditions, exclusions and IImitations hereinafter set forth:

PEAVEY OO-DAY LIMITED WARRANTY ON TUBES AND METERS

If this product contains tubes or meters, Peavey warrants the tubes or meters contained in the product to be free from defects in material and workmanshlp for a period of nmety (90) days from date of purchase; PROVIDED, however, that this limited warranty is extended only to the orlglnal retail purchaser and IS also subject to the condltlons, exclusions and IImItations hereinafter set forth.

CONDITIONS, EXCLUSIONS AND LIMITATIONS OF LIMITED WARRANTIES

These limIted warranties shall be void and of no effect if

aThe first purchase of the product is for the purpose of resale, or

b. The original retail purchase IS not made from an AUTHORIZED PEAVEY DEALER, or

c. The product has been damaged by accident or unreasonable use, neglect, improper service or maintenance, or other causes not ansmg out of defects in material or workmanship; or

d. The serial number affixed to the product IS altered, defaced or removed.

In the event of a defect in material and/or workmanship covered by this limited warranty, Peavey will: a. In the case of tubes or meters, replace the defective component without charge,

b. In other covered cases (I.e., cases Involving anything other than covers, footswitches, patchcords. tubes or meters), repair the defect in material or workmanship or replace the product, at Peavey’s option;

and provided, however, that, in any case, all costs of shlpping, if necessary, are paid by you, the purchaser.

THE WARRANTY REGISTRATION CARDSHOULD BE ACCURATELY COMPLETED AND MAILEDTOAND RECEIVED BY PEAVEY WITHIN FOURTEEN (14) DAYS FROMTHE DATE OF YOUR PURCHASE

In order to obtain service under these warranties, you must

a. Bring the defective Item to any AUTHORIZED PEAVEY DEALER or AUTHORIZED PEAVEY SERVICE CENTER and present therewith the ORIGINAL PROOF OF PURCHASE supplied to you by the AUTHORIZED PEAVEY DEALER in connection with your purchase from him of this product.

If the DEALER or SERVICE CENTER is unable to provide the necessary warranty service you will be directed to the nearest other PEAVEY AUTHORIZED DEALER or AUTHORIZED PEAVEY SERVICE CENTER which can provide such service.

Image 5
Contents AIASHVillETM Inputs NASHVILLE’ 400 General DescriptionPRE GAIN/PULL Bright Control Post Gain ControlMID EQ Control Equalization LOW EQ ControlShift Control High EQ ControlON/OFF Switch Polarity SwitchRear Panel Preamp OUT and Power AMP Footswitch Jack ‘6Peavey OO-DAY Limited Warranty on Tubes and Meters ONE-YEAR Limited WARRANTY/REMEDYMERIDIAN. MS Instructions Warranty Registration Card
Related manuals
Manual 6 pages 52.52 Kb Manual 4 pages 58.51 Kb

400 specifications

The Peavey 400 is a prominent bass amplifier that has left a significant mark in the world of music, particularly among bass players. Known for its robust construction and powerful performance, the Peavey 400 is designed to handle the demands of live performances and studio recordings alike.

One of the standout features of the Peavey 400 is its impressive power output. This amplifier typically delivers 400 watts of clean power, providing ample headroom for even the most demanding of performances. This means that musicians can achieve a rich, full sound without the risk of distortion, even at high volumes. The amplifier is equipped with a solid-state design that ensures reliable performance and durability, making it a popular choice among gigging musicians.

The Peavey 400 boasts a versatile equalization (EQ) section that allows players to sculpt their tone to suit their individual preferences. With multiple bands of EQ, including bass, middle, and treble adjustments, musicians can easily shape their sound, whether they prefer a deep, thumping low end or a more pronounced mid-range presence. This flexibility makes the Peavey 400 suitable for a wide variety of musical genres, from rock and jazz to funk and metal.

Another noteworthy characteristic of the Peavey 400 is its built-in compression system. This feature helps to even out the dynamics of the signal, ensuring a consistent output level that is particularly beneficial for maintaining clarity in live settings. Additionally, the amplifier includes an effects loop that allows players to incorporate their favorite pedal effects seamlessly into their rig, further enhancing its versatility.

The construction of the Peavey 400 is noteworthy, too. Built with a rugged chassis, the amplifier is designed to withstand the rigors of touring. The front panel typically features a clear layout of controls and inputs that allows for easy adjustment on the fly, even in low-light conditions.

In summary, the Peavey 400 combines power, versatility, and durability into one impressive package. Its robust output, flexible EQ, built-in compression, and rugged design make it a favorite among bass players seeking both reliability and quality in their sound. Whether performing on stage or recording in the studio, the Peavey 400 stands out as a dependable choice for any serious musician.