Crate Amplifiers V50-112 Tube Guitar Amplifier with Reverb Rear Panel, E a K E R V E R B

Page 5

V50-112 Tube Guitar Amplifier with Reverb

The Rear Panel

D E S I G N E D I N S T . L O U I S M O , U S A . M A N U FA C T U R E D I N C H I N A , FA B R I Q U E E N C H I N E c 2 0 0 7 L O U D T E C H N O L O G I E S I N C

F O O T S W I T C H

E F F E C T

E F F E C T

E X T E N S I O N

S P E A K E R

R E V E R B

 

S E N D

R E T U R N

S P E A K E R

8Ohms

IN

OUT

 

 

 

 

 

15 16

 

 

~120-240VAC

 

 

 

50-60 Hz

N222

 

 

 

C

US

 

AVIS: RISQUE DE CHOC ELECTRIQUE — NE PAS OUVRIR

 

3031613

 

115

CONFORMS TO

 

 

IEC 60065

 

SERIAL NUMBER

MANUFACTURING DATE

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE. DO NOT REMOVE COVER. NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED PERSONNEL.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1)This device may not cause harmful interference, and

(2)This device must accept any interference received, including interference that may cause undesired operation.

17

18

19

20

21

22

23

15.AC LINE CORD: The grounded power cord should only be plugged into a grounded power outlet that meets

all applicable electrical codes, and is compatible with the voltage, power, and frequency requirements stated on the V50-112 rear panel. Do not attempt to defeat the safety ground connection.

16.Voltage Select Switch: Set this switch to “115” for 120 VAC mains, and to “230” for 220-240 VAC mains.

With the amplifier power cord unplugged, use the tip of a small flat- blade screwdriver to slide this switch to the proper position.

17.FOOTSWITCH Jack: Use this 1/4" TRS jack to connect the cable of the optional VSFS-2 footswitch. This allows for remote control of channel switch- ing and the boost effect (Tip = channel select, Ring = boost on/off).

18.EFFECT SEND: Use this 1/4" TS jack to send the signal to an external effects box.

Note: The Effect Send jack can be used as a line-level output from the preamplifier stage of the V50-112 to a mixer or recorder. The signal comes after the EQ stage but before the reverb stage.

19.EFFECT RETURN: Use this 1/4" TS jack to return the signal from an exter- nal effects box.

A Closer Look: The Effect Send and Effect Return create an Effect Loop, where the guitar signal is sent out to an external effects box (like a digital delay), and the processed signal is returned to the amplifier.

Note: The Effect Return jack discon- nects the signal from the preamplifier stage of the V50-112, so only the sig- nal at the Effect Return jack is sent on to the power amplifier.

20.EXTENSION SPEAKER: Use this 1/4" TS jack to connect the amplifier to an 8 ohm extension speaker. The internal speaker remains active when an exten- sion speaker is connected.

21.SPEAKER 8 OHMS: The V50-112 is shipped with a cable connected from this jack to the internal speaker.

22.REVERB IN Jack: The V50-112 is shipped with a cable connected from this jack to the input of the internal spring reverb.

22.REVERB OUT Jack: The V50-112 is shipped with a cable connected from this jack to the output of the internal spring reverb.

5

Image 5
Contents V50-112 Table of Contents V50-112 Tube Guitar Amplifier with Reverb Introduction V50-112 Tube Guitar Amplifier with Reverb Front Panel E a K E R V E R B V50-112 Tube Guitar Amplifier with Reverb Rear PanelTube Types And Usage Brief History Of The TubeImportant Information About Tubes and Tube Products Nature Of Tubes Why And When To Replace ThemImportance Of Proper Biasing Whenever you replace the power tubesSurvival Tips For Tube Amplifiers Sweet ‘n Clean Treble MID Bass Boost Presence Declaration Of ConformityV50-112 Technical Specifications Service Information