Specifications, Replaceable Cross Fader, Inputs

PS-01

the CUE BUTTONS (28, 35, 42) for CH 1 through CH 3 to assign the CH(s) to be monitored in your headphones. The respective CUE LED indicators will glow when in use.

NOTE: DO NOT APPLY PRESSURE WHILE USING THE CROSS FADER (46). LIGHTLY GLIDE THE CROSSFADER BACK AND FORTH. PRESSING DOWN ON THE CONTROLS CAN BEND CONTACTS AND CAUSE A LOSS OF SOUND.

Use the face panel located rotary CUE VOLUME CONTROL

(44)to adjust the CUE volume without changing the overall mix. By turning the face panel located CUE/MIX/PGM ROTARY CONTROL (45) counter clockwise you will be able to monitor the assigned cue signal. Slowly turning the control clockwise to middle position allows you to monitor CUE MIX with PGM. Moving the control clockwise to the right allows you to monitor PGM output.

Use the CUE SPLIT/MIX SWITCH (48) to split the audio input playing in your head phones. When the CUE SPLIT/MIX SWITCH (48) is in MIX mode you will only be able to monitor your CUE. When the CUE SPLIT/MIX SWITCH (48) is in SPLIT mode, you will notice one side of your headphones will play your cue and the other side will play PGM, thus enabling you to mon- itor both outputs separately. This feature will only work properly if the CUE/MIX/PGM (45) rotary control is placed at noon or mid- dle position. If the CUE/MIX/PGM (45) rotary control is set to CUE you will only here the CUE signal playing on the left side of your headphones. If the CUE/MIX/PGM (45) rotary control is set to PGM, the PGM will be the only signal heard from the right side of your headphones.

6.CROSS FADER SECTION: The CROSS FADER (46) allows you to mix from one source to another. The CROSS FADER (46) in your unit is removable and if the need arises can be easily replaced. Your Gemini mixer comes with an RG-45 (RAIL-

GLIDE™) DUAL-RAIL CROSS FADER. RAIL GLIDE™ CROSS FADERS have internal dual stainless steel rails that allow the slider to ride smoothly and accurately from end to end. Also available is our RG-45 PRO (PROGLIDE™) DUAL-RAIL CROSS FADER. This unique CROSS FADER features, a spe- cial curve designed for scratch mixing. Just purchase one from your Gemini dealer and follow the instructions:

REPLACEABLE CROSS FADER

1.UNSCREW THE OUTSIDE FACE PLATE SCREWS ON THE LOWER HALF OF THE MIXER. REMOVE THE FADER CAPS AND FACE PLATE.

2.UNSCREW THE FADER (B)

SCREWS. DO NOT TOUCH INSIDE SCREWS (C). CAREFULLY REMOVE OLD CROSS FADER AND UNPLUG CABLE (D).

3.PLUG IN THE NEW CROSS FADER INTO CABLE (D) AND PLACE BACK INTO MIXER.

4.SCREW THE CROSS FADER TO MIXER WITH THE FADER PLATE SCREWS (B).

5.REPLACE THE LOWER HALF FACE PLATE AND SCREW TO THE MIXER.

7.OUTPUT SELECTION CONTROL: Once you are comfort- able with the sound level of your music you may adjust the vol- ume with the MASTER (47) slide control. You may adjust the volume of the zone output with the ZONE (51) rotary control. You may also pan the audio output from left to right with the BALANCE (52) rotary control.

8.MIC SECTION: Plug your main MIC into the MIC 1/4" input (21) located on the front panel.

9.VU METER: The PS-01 has a dual mode VU METER (50) that allows you to monitor the decibel levels of CUE and PGM or LEFT and RIGHT stereo levels of the MASTER output. With the VU MODE SWITCH (49) you may monitor the output level of the CUE and PGM when the switch is UP. When this mode is engaged the CUE will be located on the left of the VU METER, while the PGM will be located on the RIGHT. Or you can moni- tor the LEFT and RIGHT stereo decibel levels of the MASTER OUTPUT when the switch is in the DOWN position.

SPECIFICATIONS:

INPUTS:

Phono	..................................................................3 mV, 47 KOhm
Line	150 mV, 27 KOhm
MIC…………..........……….................1.5 mV, 1 KOhm Balanced

OUTPUTS:

Amp/Zone	........................................................0 dB 1V, 400 Ohm
Max	20V Peak-to-Peak
Rec	225 mV, 5 KOhm
Balanced Master……………...............................….2V, 400 Ohm

GENERAL:

Frequency Response	20Hz - 20KHz +/- 2 dB
Distortion	< 0.02%
S/N Ratio	Better Than 80 dB
Headphone Impedance	16 Ohm
Power Source	115/230 V, 60/50 Hz, 20 W
Unit Dimensions	10" x 3.3" x 11.9"

…………………………………………….....(254 x 84 x 303 mm)

Weight

6.93 lbs (3.15 kg)

SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTIFICATION FOR IMPROVEMENT.

(5)