Gemini PDM-14 manual Specifications, Outputs

Page 5

1.Unscrew the outside FADER PLATE SCREWS (B). Do not touch the INSIDE SCREWS (C).

2.Carefully lift the fader and unplug the CABLE (D).

3.Plug the new fader into the cable and place it back in the mixer.

4.Screw the fader to the mixer.

7.EQUALIZER SECTION: This unit features dual 7 band GRAPHIC EQUALIZERS (8, 22) to allow you to adjust the sound for any room. To activate the equalizer, press the EQ BUTTON (28) (the EQ LED will light). By adjusting any of the 7 left equalizer slide controls (8), you can cut or boost the tonal characteristics of the sound coming from the left speaker by ±12 dB. By adjusting any of the 7 right equalizer slide controls (22), you can cut or boost the tonal characteristics of the sound coming from the right speaker by ±12 dB. Deactivate the equalizer by pressing the EQ BUTTON (28) again (the EQ LED will turn off).

8.OUTPUT CONTROL SECTION: The level of the MAIN OUTPUT (34) is controlled by the MASTER (24) slide. Activating the MONO (23) button (the mono LED will light) makes the overall output mono. The BOOTH (29) control adjusts the level of the BOOTH OUTPUT (35). HINT: The BOOTH OUTPUT is used by some DJs to run monitor speakers in their DJ Booth. You can also use it as a second ZONE or AMP output.

NOTE: The REC OUTPUT (36) has no level control. The level is set by the channel slides of the selected channel. The tonal qualities can be controlled by the equalizers.

9.TALKOVER SECTION: The purpose of the talkover section is to allow the program playing to be muted so that the mic can be heard above the music. The MIC/TALKOVER SWITCH (7) controls MIC 1 and MIC 2 and has three settings. When the MIC/TALKOVER SWITCH (7) is in the bottom position, MIC 1 and MIC 2 and talkover are off. When the MIC/TALKOVER SWITCH (7) is in the center position MIC 1 and MIC 2 are on, the MIC INDICATOR (6) will glow, but talkover is off. When the MIC/TALKOVER SWITCH (7) is in the top position, MIC 1 and MIC 2 and talkover will be on and the volume of all sources except the Mic inputs are lowered by 16 dB. The TREBLE (2) and BASS (3) controls allow you to fully adjust the tone of MIC 1 and MIC 2. MIC 1 LEVEL (5) controls the level of MIC 1. The MIC 2 LEVEL (4) controls the level of MIC 2.

10.CUE SECTION: By connecting a set of headphones to the HEADPHONE (32) jack, you can monitor any or all of the channels. Press the CUE ASSIGN (20) buttons for channels 1 - 4 to select the channel or channels to be monitored and their respective LED indicators will glow. Use the CUE LEVEL (31) control to adjust the cue volume without effecting the overall mix. By moving the CUE PGM PAN (30) control to the left you will be able to monitor the assigned cue signal. Moving the control to the right will monitor the PGM (program) output.

11.DISPLAY: The DISPLAY (21) indicates the MASTER output left and right levels.

Specifications

INPUTS:

 

 

 

 

DJ Mic

1.5mV 2Kohm balanced

Phono

 

3mV 47Kohm

Line

150 mV 27Kohm

OUTPUTS:

 

 

 

 

Amp/Booth

0 dB 1V 400ohm

Max

20V

Peak

to

Peak

Rec

 

225mV 5Kohm

MIC 1 & MIC 2:

 

 

 

 

DJ Mic

1.5mV 2Kohm balanced

Bass

 

 

± 12dB

High

 

 

± 12dB

GENERAL:

 

 

 

 

Frequency Response

20Hz - 20KHz +/- 2dB

Distortion

 

 

0.02%

S/N Ratio

better than 80dB

Talkover Attenuation

 

 

-16dB

Headphone Impedance

 

 

16ohm

Echo

 

 

600msec

Power Source

115/230V 50/60Hz 10W

Dimensions

19”w x 4”d x 9”h (483 x 94 x 221 mm)

Weight

10.17 lbs (4.6 kg)

Page 4

Image 5
Contents PDM-14 Page Page Using the Ground Lift Switch FeaturesIntroduction ConnectionsOutputs SpecificationsGemini Sound Products Corp All Rights Reserved