Ashly MX-406 manual Specifications

Page - 10 Operator Manual – MX-406 Mixer

Safety Instructions – 3

Introduction - 4

MX-406 Mixer – 5

Connectors & Cables – 5

Physical Description - 6

Installation – 7

Typical Applications - 8

Factory Configs - 8

Troubleshooting - 9

Dimensions - 9

Specifications - 10

Warranty - 11

Specifications

SPECIFICATION

MX-406

DISTORTION

THD at +4 dBu, 20Hz-20KHz

<0.05%

THD at +12dBu, 30Hz-10KHz

<0.05%

IMD (SMPTE) at +12dBu

<0.05%

HUM & NOISE (20Hz-20KHz at max preamp gain)

Equivalent input hum and noise

<-127dBu

Residual output noise, TRS outputs, all levels at minimum

<-100dBu

Aux Out, Aux Master and all Ch. Aux at nom.

<-80dBu

MAXIMUM VOLTAGE GAIN (±2dB)

MASTER

Mic/Line Input to Master Output

+84dB

Mic/Line Input to Mono Output, 600 ohm load

+84dB

AUX SENDS

Mic Input to Aux Master Output, pre ch. level

84dB

Mic Input to Aux Master Output, post ch. level

99dB

Stereo Line in to Aux Master Output

32dB

FREQUENCY RESPONSE

20Hz-20KHz

+0.5/-1.0dB

EQUALIZATION

Bass

±12dB at 70Hz, shelving

Treble

±12dB at 8KHz, shelving

CROSSTALK

Adjacent inputs, 20Hz-20KHz

<-65dB

VU METERS (Stereo Outputs) 0VU = +4dBu

-21 to +6 VU

PEAK INDICATORS

Peak Clip indicator on each input channel and left and right outputs,

illuminates 3dB below clipping

+48 VDC applied to all Mic Inputs, switchable on front panel.

PHANTOM POWER

Maximum total current draw = 80mA.

Maximum single channel current draw = 14mA.

Gradual power-up and down to eliminate "pops".

SHIPPING WEIGHT

15 lbs.

POWER REQUIREMENTS

100-240 Volts, 50-60 Hz – 30 watts

Unless otherwise stated, specification conditions are: 150 source, Input Level set at "-40", all other controls set at nominal.

Input Specifications

Input

Balanced/

Input Level & Pad

Load

For use w/

Sensitivity

Max Input

Connector

Unbalanced

Impedance

Nominal

before Clip

Mic 1-6

Balanced

Input level @ -60 (pad out)

1K

50 to

-80 dBu

-29 dBu

Female XLR

Input level @ -20 (pad out)

-40 dBu

+10 dBu

1/4”TRS

600 mics

Input level @ -20 (pad in)

-20 dBu

+29 dBu

Combo Jack

Input level @ -60 (pad out)

10K

-52 dBu

-2 dBu

Female XLR

Line 1-6

Balanced

600 lines

1/4”TRS

Input level @ -20 (pad in)

+8 dBu

+30 dBu

Combo Jack

Sub Inputs

Unbalanced

NA

10K

600 lines

-12 dBu

+23 dBu

1/4” TRS

Stereo Line In

Unbalanced

NA

10K

600 lines

-24 dBu

+23 dBu

RCA

Output Specifications

Output

Balanced/

Source

For use w/

Output Level

Output Level Max

Connector

Unbalanced

Impedance

Nominal

Nominal

before Clip

Master Out (L, R)

Servo Balanced

200

600 lines

+4 dBu

+23 dBu

1/4” TRS

Mono Out

Transformer Balanced

600

600 lines

+4 dBu

+23 dBu

Female XLR

Aux Out

Servo Balanced

200

600 lines

+4 dBu

+23 dBu

1/4” TRS

Stereo Line Out

Unbalanced

680

10 K lines

-6 dBu

+12 dBu

RCA

(L, R)

Notes: 1.

0 dBu = 0.775 Vrms 2. Sensitivity is input signal level which will produce +4 dBu out with all levels maximum

Copyright© 2007 – Ashly Audio Inc.