TOGGLE SWITCHES:
RHYTHM / LEAD / CONTOUR:
RHYTHM |
| ON | ON |
F | L |
|
|
T | E |
|
|
S | A |
|
|
W | D |
|
|
CONTOUR | STANDBY | POWER | |
Use this toggle to select one of the three Modes - RHYTHM, LEAD or CONTOUR. This toggle can also take the place of the remote footswitch when there isn’t one handy.
ON / STANDBY: | Perfect for set breaks...this toggle switch also serves an even more important purpose. In the STANDBY | ||||
|
|
|
|
| position the tubes are at idle so that during power up they may warm up before being put |
|
|
|
|
| |
RHYTHM |
| ON | ON | to use. Before the Power is switched on, make sure the STANDBY switch is in the | |
|
| ||||
| L |
|
|
| STANDBY position. Wait at least 30 seconds and then switch the STANDBY to the |
F |
|
|
| "ON" position. This helps in preventing tube problems and increases their toneful life | |
S | A |
|
|
| |
T | E |
|
|
|
|
W | D |
|
|
| substantially. |
|
|
|
|
| |
CONTOUR | STANDBY | POWER |
| ||
POWER: |
| This switch delivers the A.C. power to the SUBWAY ROCKET. Make sure the unit is grounded (all three | |||
|
|
|
|
| terminals of the A.C. power cord must be connected whenever possible to avoid injury to |
|
|
|
|
| |
RHYTHM |
| ON | ON |
| the user as well as to the unit) and that the proper voltage is present. Follow the cold start |
|
|
| |||
|
|
|
|
| procedure described in the ON / STANDBY section above when powering up your |
F | L |
|
|
| ROCKET. |
S | A |
|
|
| |
T | E |
|
|
|
|
W | D |
|
|
|
|
CONTOUR | STANDBY | POWER |
|
| |
|
| ||||
REAR PANEL:
12 A | SUBWAY ROCKET |
|
| DYNA |
|
|
|
|
|
|
|
| SPEAKERS |
| |
FUSE |
|
|
|
|
| ||
4,701.957 |
|
|
|
|
|
| |
| 100 % |
|
|
|
|
| |
1A SB | 0% |
|
|
|
|
| |
| FX MIX |
|
|
|
|
| |
|
|
|
|
|
|
| |
RECORD / PHONES | SEND | RETURN |
|
|
|
|
|
|
| MUTE | SPKR | ON | 8 OHM | 4 OHM | 4 OHM |
|
|
|
|
| |||
|
| SILENT RECORDING | HANDBUILT IN PETALUMA, CALIFORNIA. |
|
| ||
|
|
|
|
|
|
| |
This is the A.C.’s ( Alternating Current ) main fuse and provides protection from outside A.C. fluctuations, as well as power tube failure damage. Should the fuse blow, replace it with the same rating in a
STANDBY Switch to STANDBY immediately and replace the faulty power tube and the fuse if necessary. If you see nothing abnormal as you lift the STANDBY, it is possible that a power tube shorted temporarily and blew the fuse. If this is the case it may work again normally. To be extra safe you may want to replace all power tubes in the "shotgun" troubleshooting tradition and save the replaced set as spares. Don’t forget to carry along a few extra fuses to your gigs, they could be worth their weight in
PAGE 5