Breckwell P23FSA, P23I, P23FSL owner manual Equivalent Vent Length EVL, Freestanding Installations

Page 7

INSTALLATION

Equivalent Vent Length (EVL)

The longer the run of pipe in your installation (both with insert and freestanding models), the more restriction there is in the system. Therefore, larger diameter pipe should be used.

∙Use 4” pipe if you have more than 15 feet of equivalent vent length.

∙Horizontal runs shall not exceed 10 feet of EVL.

∙Recommended vertical runs to be a minimum of 8 feet.

∙To calculate EVL, use the following conversions:

90º elbow or “T”

= 5 equivalent feet

45º elbow

= 3 equivalent feet

Horizontal Pipe Run

= 1 equivalent foot per actual foot

Vertical Pipe Run

= 0.5 equivalent foot per actual foot

NOTE: At altitudes above 3,000 feet, we suggest the use of 4” diameter vent at an EVL of 7 feet or more.

FREESTANDING INSTALLATIONS

A.ASSEMBLING PEDESTAL OR LEG SET (Refer to figure 8)

If using a pedestal, follow the instructions inside the Breckwell

P23 Pedestal w/ Ashpan.

If using cast legs, follow the instructions inside the Breckwell P23

Leg Set w/ Ashpan.

Legs are installed by inserting the four bolts provided in the kit into the four holes in the bottom plate of the stove at each corner from the top, thread on the nuts from the bottom and tighten.

FIGURE 8

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Tradition Series P23 Important Information IntroductionSafety Precautions Table of Contents Clearances InstallationSpecifications PreparationSources of Outside Combustion Air When Outside AIR is not UsedCombustion AIR Supply VentingEquivalent Vent Length EVL Freestanding InstallationsAssembling Pedestal or LEG SET Refer to figure Horizontally Through Wall refer to Figure Vertically Into Existing Chimney System Vertically with NEW Chimney System Refer to FigureVertically Into Existing Masonry Fireplace Installation Through Side of Masonry ChimneyAssembling the Flashing SET Insert InstallationsWhen Vent Pipe Extends Through Chimney Blanking Plate When Vent Pipe Extends to Chimney TOP Refer to Figures 16AS a BUILT-IN Fireplace Chase dimensions shown are minimums and must be maintainedInstallation in to a Factory Built Metal Fireplace Electrical Installation Special Mobile Home RequirementsOperation Hotrod Automatic Firestarter Proper FuelPRE-START-UP Check Building a FireRE-STARTING a Warm Stove Breckwell Maintenance ToolShutdown Procedure Safety Features∙ a Millivolt Thermostat is Required Thermostat InstallationThermostat Installation Optional ThermostatPlease Read this ASH Disposal Insert MaintenanceASH Removal ASH Disposal Freestanding ModelsVacuum USE CleaningBlowers Daily Weekly Bi-Annually Annually or per Ton Chimney CleaningStove Shuts OFF and the # 2 Light Flashes Troubleshooting GuidePossible Causes Stove Shuts OFF and the # 3 Light Flashes Convection Blower Shuts OFF and Comes Back on Stove Feeds PELLETS, but will not IgnitePossible Causes Possible Remedies Smoke Smell Coming Back Into the HomeFuel feed light is on, you have a bad control board Troubleshooting Guide Digital Circuit Board Timing Rates High Limit Switch Keeps TrippingHeat Level Setting P23 Smoke Smell or Soot BUILD-UPElectrical Diagram Burnpot Replacement PartsLifetime Limited Warranty
Related manuals
Manual 30 pages 36.97 Kb Manual 30 pages 36.5 Kb

P23FSL, P23FSA, P23I specifications

The Breckwell P23 series pellet stoves, comprising the P23FSA, P23I, and P23FSL models, are designed to provide efficient heating solutions while maintaining ease of use and aesthetic appeal. These stoves incorporate advanced technology features that set them apart in the modern heating market.

The Breckwell P23FSA model features a traditional freestanding design that blends seamlessly with any home decor. This model is equipped with a large viewing window, allowing users to enjoy the mesmerizing flames while benefiting from its high-efficiency heating capabilities. With a heating capacity of up to 2,000 square feet, it is an ideal choice for larger spaces. The P23FSA uses a digital control board that regulates the feed rate and blower settings, ensuring a consistent and reliable heat output. Additionally, it has a self-diagnostic system that alerts users to any operational issues, making maintenance straightforward.

The P23I, on the other hand, is designed for those seeking a built-in option. This insert offers the same heating capacity as its freestanding counterpart but is specifically made to fit into existing fireplaces, combining functionality with elegance. The P23I boasts a sleek design that enhances any room, while its adjustable blower ensures optimal heat distribution. The insert is also compatible with an optional wall thermostat, providing convenience and enhanced control over the heating schedule.

Lastly, the P23FSL model features a contemporary look with sleek lines and a compact design, ideal for smaller spaces without compromising on heating efficiency. This model includes a large hopper capable of holding up to 50 pounds of pellets, allowing for extended burn times and reduced refueling frequency. The P23FSL also incorporates a user-friendly control panel, providing adjustments at the touch of a button. Like the other models, it prioritizes efficiency, with a low emissions output that aligns with modern environmental standards.

All three models are built with high-quality materials to ensure durability and longevity. They utilize a pellet-burning process that significantly reduces environmental impact compared to traditional wood stoves, making them an eco-friendly heating option. With their combination of technology, efficiency, and aesthetic appeal, the Breckwell P23 series stands out as a top choice for homeowners looking for reliable and stylish heating solutions.
Top Page Image Contents