Pump Option Description Chart

650879- X X X

Packing Material

Spring Arrangement

Plunger Type

PACKING MATERIAL (Packings are upper and lower unless noted) J - Polyurethane (upper)

UHMW-PE (lower)

SPRING ARRANGEMENT

3 - No spring

PLUNGER TYPE

D - Hard stainless steel with hard chrome plating

GENERAL DESCRIPTION

PUMP CONNECTION - UPPER / LOWER

The chop-check pumps are primarily designed for the pumping of heavy viscous material with or without fibrous content. The models can be used with a gravity feed single post lift as a topper type assembly or with a two post lift as a force feed type assembly. The lower pump is designed for easy priming and the double acting feature is standard in all Ingersoll Rand industrial pumps. Material is delivered to the pump discharge outlet on both the up and down stroke.

The motor is connected to the lower pump end by a spacer section. This allows for lubrication of the upper packing gland and prevents motor contamination because of normal wear and eventual leak- age through the material packing gland. Be sure the lubricant cup is adequately filled with lubricant to protect the upper packings and insure longest service life.

WARNING HAZARDOUS PRESSURE. Do not exceed maxi- mum operating pressure of 3360 p.s.i. (231.7 bar) at 120 p.s.i. (8.3 bar) inlet air pressure.

Pump Ratio X	=	Maximum Pump
Inlet Pressure to Pump Motor		Fluid Pressure

Pump ratio is an expression of the relationship between the pump motor area and the lower pump end area. EXAMPLE: When 150 p.s.i. (10.3 bar) inlet pressure is supplied to the motor of a 4:1 ratio pump, it will develop a maximum of 600 p.s.i. (41.4 bar) fluid pressure (at no flow) - as the fluid control is opened, the flow rate will increase as the motor cycle rate increases to keep up with the demand.

WARNING Refer to general information sheet for additional safety precautions and important information.

NOTICE: Thermal expansion can occur when the fluid in the mate-

rial lines is exposed to elevated temperatures. Example: Material lines located in a non-insulated roof area can warm due to sunlight. Install a pressure relief valve in the pumping system.

Replacement warning label (pn 92325) is available upon re- quest.

TROUBLE SHOOTING

Pump problems can occur in either the air motor section or the lower pump end section. Use these basic guidelines to help deter- mine which section is affected.

Pump will not cycle.

yBe certain to first check for non-pump problems including kinked, restrictive or plugged inlet / outlet hose or dispensing device. Depressurize the pump system and clean out any ob- structions in the inlet / outlet material lines.

yRefer to the motor manual for trouble shooting if the pump does not cycle and / or air leaks from the air motor.

yDamaged motor. Service the motor.

Pump cycles but does not deliver material.

yRefer to the lower pump end manual for further trouble shoot- ing.

NOTE: All threads are right hand.

1.Lay the pump assembly on a work bench.

2.Remove the three (Y6-128-C) cap screws and (Y14-750-K) lock washers from the three spacer rods (see figure 1).

3.Pull the air motor from the lower pump end until the motor piston rod is in the “down” position and the lower pump end rod is in the “up” position.

4.Remove the three spacer rods by removing the three (Y6-128-C) cap screws and (Y14-750-K) lock washers.

5.Using e-ring pliers, slide the “e” ring up far enough to allow the sleeve to move upward and release the two connectors (see figure 2).

PUMP CONNECTION DETAIL

Pump Motor Piston Rod

95069 “E” Ring

94688 Connector (2)

94689 Sleeve

Lower Pump Piston Rod

Figure 2

REASSEMBLY

1.Align the pump motor with the lower pump end. Position the air inlet of the motor 150° from the material outlet.

2.Install the two connectors (94688) and retain with the sleeve (94689). Slide the “e” ring (95069) back into position.

3.Assemble the three spacer rods (93866) to the lower pump and secure using three (Y14-750-K) lock washers and (Y6-128-C) cap screws.

4.Reinstall the spacer rods to the pump motor.

5.Bring the motor and lower pump together and retain with three (Y14-750-K) lock washers and (Y6-128-C) cap screws.

PN 97999-971

Page 2 of 2

650879-XXX (en)

650879-XXX specifications

The Ingersoll-Rand 650879-XXX is a highly regarded industrial air compressor, known for its robust design and advanced technologies that cater to a variety of demanding applications. Engineered for reliability and efficiency, this model is a preferred choice among professionals in sectors such as construction, manufacturing, and energy.

One of the standout features of the Ingersoll-Rand 650879-XXX is its powerful motor, which ensures consistent performance even under heavy load conditions. This air compressor is designed to deliver high airflow rates, making it suitable for tasks requiring a steady stream of compressed air, such as powering pneumatic tools and equipment. The motor's energy-efficient design not only reduces operational costs but also contributes to environmental sustainability.

In terms of technology, the Ingersoll-Rand 650879-XXX incorporates advanced rotary screw compression technology. This innovation allows for smoother and quieter operation compared to traditional piston compressors. The rotary screw mechanism reduces wear and tear, prolonging the lifespan of the unit and minimizing maintenance needs. As a result, users benefit from enhanced reliability and lower total cost of ownership.

The unit's tank capacity is another key characteristic that adds to its functionality. With an adequately sized tank, the compressor can store a significant amount of compressed air, ensuring that it can handle extended periods of operation without the need for constant refilling. Additionally, the integrated moisture separator helps in maintaining air quality by removing contaminants from the compressed air, which is essential for protecting sensitive tools and equipment.

Another important feature is its user-friendly control panel, which allows for easy operation and monitoring of performance metrics. This intuitive interface provides operators with real-time data, facilitating timely adjustments and maintenance scheduling.

Furthermore, the Ingersoll-Rand 650879-XXX is built with durability in mind, featuring high-quality materials and a rugged construction that can withstand the rigors of industrial environments. Its portability makes it easy to transport across job sites, while its compact design saves valuable floor space.

In summary, the Ingersoll-Rand 650879-XXX stands out due to its powerful performance, innovative technologies, and user-friendly features. With its reliable operation and focus on efficiency, it continues to be a top choice for professionals seeking a dependable air compressor to meet their industrial air supply needs.