Centro 2000 warranty I O R T O U S I N G, Hose and Regulator Inspection

Page 5

P R I O R T O U S I N G

Insert valve outlets into Venturi tubes

approximately 6 mm (1/4”)

Drawing E

W A R N I N G

Natural Hazards

Insects and Spiders

Drawing F

Do not use your barbecue until you have carefully read and fully understand all the information in this manual. Please ensure the following:

•Your barbecue is properly assembled.

•There are no leaks in the system (see “Leak Test”).

•The burner is properly assembled, with the Venturi tubes seated over the valve outlets (Drawing E) and that there is nothing blocking the Venturi tubes (Drawing F).

•Ensure that all power cords and / or gas supply hoses will not touch or be near surfaces that will get hot.

•The barbecue is in a safe location (see Installation).

Ensure that the valve outlets (orifices) are assembled into the Venturi tubes approximately 6 mm (1/4˝ ) and that the valve outlets and Venturi tubes are approximately parallel to the bottom of the lower body.

During shipment or storage, it’s possible that small insects like spiders could find their way into the Venturi tubes and nest or make webs. This could block the flow of gas through the Venturi tube causing a smoky yellowish flame, or prevent a burner from lighting. It could even cause the gas to burn outside the Venturi tube, which could seriously damage your barbecue. If these occur, turn off the gas flow and wait for the barbecue to cool down. When the barbecue has cooled, remove the burner and clean out the Venturi tubes with a brush or pipe cleaner. Replace the burner and ensure that the Venturi tubes are seated over the orifice located on the gas valves. Cleaning the Venturi tubes should be conducted periodically, especially at the start of the season.

Note: Damage resulting from blocked Venturi tubes is not covered under the warranty.

Orifice Size: The orifice, in conjunction with the control valve, acts to regulate and restrict the amount of gas delivered to the burner. The hole size in the orifice varies by the gas sup- ply pressure and by the BTU rating of the burner. Grills equipped for LP gas operate at a much higher gas pressure and therefore have a smaller size orifice.

Hose and Regulator Inspection

Adjustment: The regulator is factory set at a specified outlet pressure of 11” of water column and is generally factory sealed and not adjustable. Do not try to adjust. The regulator can be checked by measuring the pressure with a manometer.

Vent Hole: There is a vent hole on top of the regulator. Check that it is clear of dirt and debris. If the hole is plugged, erratic and dangerous burning may result.

O-ring Seal: Before attaching the regulator to the cylinder, inspect the rubber O-ring on the P.O.L. fitting. Do not operate the grill if the O-ring is damaged or missing. Seal damage is common and we recommend replacement of the seal when the burner is replaced or when the seal is damaged. Cracks, splits or distortion will allow gas to escape. Additionally, the seal should be soft, pliable, and protrude slightly from the brass P.O.L. valve.

Chew Marks: The hose should be kept clean of grease and food drippings which attract squirrels and other animals. The animals will often eat the drippings on the hose and chew into the hose lining trying to get the last taste. Try cleaning the hose with an ammonia cleaner solution to minimize the attration.

3

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Serial # BarbecueB L E O F C O N T E N T S E O F L P G a S C Y L I N D E R Installation I N F O R M a T I O ND I T I O N a L R N I N G S L L I N G T H E L P C Y L I N D E R Cylinder must also be equipped withTo Avoid Unnecessary Risks Hose and Regulator Inspection I O R T O U S I N GF E T Y H O S E D R E G U L a T O R F E T Y A K T E S T I N G To Reset The Gas Regulator Safety DevicePerform a Leak Test Following Must Be CheckedR N I N G If the Selected Burner does not Light G H T I N G E G R I L LMatch Lighting The Main Burners Turning The Burners OffItem No Quantity Specification 1 1 0 3 P R O P a N E G 4 1 3 0 R T S L I S T I N G F O R 1 0 0 3 6 N a T U R a L G a S G 4 1 3 0 Hardware Pack List Tools Needed for AssemblyS E M B L Y I N S T R U C T I O N S Page Page CJ + CK For propane model only Disconnecting From Gas Line Connecting to Gas LineF O R M a T I O N O N T U R a L G a S M O D E L Natural Gas Supply ConnectionS T R I B U T O R

2000 specifications

Centro 2000 is a cutting-edge commercial complex that has become a significant landmark in urban development, combining modern architecture with innovative technologies to cater to diverse business needs. Located in a bustling urban area, Centro 2000 serves as a multifunctional space that accommodates offices, retail, and leisure facilities, making it a hub for both professionals and consumers.

One of the main features of Centro 2000 is its sustainable design. The building employs energy-efficient technologies, including solar panels and green roofs that help reduce the carbon footprint. These features are complemented by advanced insulation systems and smart energy management to optimize temperature control throughout the complex. The use of renewable energy sources not only promotes environmental sustainability but also significantly lowers operational costs.

Centro 2000 is equipped with state-of-the-art communication technologies. High-speed internet and extensive Wi-Fi coverage are available throughout the premises, ensuring seamless connectivity for businesses and visitors alike. The building incorporates smart building technologies, including automated lighting, smart HVAC systems, and advanced security measures, enabling efficient management and enhanced safety. These innovations create a responsive environment that can adapt to the needs of its occupants.

The architectural design of Centro 2000 emphasizes open spaces and natural light, featuring large windows and spacious communal areas. This layout fosters collaboration and interaction among tenants and visitors, enhancing the overall experience within the complex. The inclusion of recreational areas, such as parks and lounges, adds to the aesthetic appeal, creating a pleasant environment for both work and leisure.

Accessibility is another key characteristic of Centro 2000. The complex is strategically located near major transport links, providing easy access for both employees and customers. Ample parking spaces are available, and facilities for bicycles and electric vehicles have been incorporated to encourage eco-friendly commuting options.

In summary, Centro 2000 stands out as a remarkable example of modern urban development. Its blend of sustainable technologies, innovative communication systems, and collaborative spaces creates not only a functional environment but also an attractive destination for businesses and consumers. The commitment to sustainability and modern architectural design positions Centro 2000 as a forward-thinking complex that is well-equipped to meet the demands of a dynamic urban landscape.
Top Page Image Contents