Radio Shack 63-1089 manual Indoor/outdoor thermometer and hygro sensor, Your sensor Battery notes

63-1089

indoor/outdoor thermometer and hygro sensor

Thank you for purchasing your Indoor/Outdoor Thermometer and Hygro Sensor from RadioShack. You can mount it on a wall or place it on a flat surface using the included stand. Your thermometer displays indoor and outdoor temperatures, as well as humidity information. And, your thermometer even features an atomic alarm clock.

in your sensor			battery notes
Remove the battery compartment cover.			• For the best results, install batteries in
Insert two AAA batteries, matching the polarity symbols (+ and -),			the remote sensor first, and then the
marked inside.			thermometer. Press RESET after each
Select CHANNEL 1, 2, or 3 inside the compartment.			battery replacement.
Press RESET to initialize the transmission.			• ) displays when battery power is low.
Replace the cover and secure it with the screws.			• Dispose of old batteries promptly and
in the thermometer			properly. Do not burn or bury batteries.
Remove the battery cover.			• Do not use rechargeable batteries.
			• Use only fresh batteries of the required size
Insert two AA batteries, matching the polarity symbols
(+and -) marked inside.			and recommended type.
Replace the battery cover.			• Do not use batteries of different types
			capacities, or chemistries.
Replace the batteries when the low battery icon appears. Press RESET			• If you do not plan to use this product for a
			month, remove the batteries. Batteries can
when you replace the batteries, or if it does not perform normally. All
			leak chemicals that can damage electronic
settings will return to the default values and you will lose all stored
information.	RESET	C°/F° Switch	parts.

Note: Actual product may vary from the images found in this document.

thermometer and stand • thermo-sensor

user’s guide

Please read this user’s guide before

installing, setting up and using your new product.

www.radioshack.com

You can place your thermometer and sensor on a flat surface, using the included stand or you can mount them on a wall. Insert your wire stand into the holes on the back of your sensor and place it in a desired location.

Keyhole Slot	mounting your thermometer
	Drill a hole in the wall.
	Thread a screw (not supplied) into the hole,
	letting it extend about 3/16” from the wall. Be
	sure to use a screw with a head that fits into the
	keyhole slot.
	Slide the thermometer down until it is secure.
mounting your sensor
Drill a hole in the wall.		Keyhole Slot

Thread a screw (not supplied) into the hole, letting it extend about 3/16” from the wall. Be sure to use a screw with a head that fits into the keyhole slot.

Slide the sensor down until it is secure. CHANNEL

Be sure to insert the batteries before you mount your sensor.

Press RESET on the sensor to receive a signal. Then, press and hold MEMORY and CHANNEL on your thermometer to search for the sensor.

º- - º blinks on your thermometer while it is searching. To clear readings in memory, press and hold MEMORY for 2 seconds. A beep sounds to confirm the memory is clear.

If you have more than one sensor, select a different channel for each one. Three signal icons display when at least one channel has been found.

selecting sensor channels

To auto-scan between sensors, press and hold CHANNEL for 2 seconds. Each sensor’s data will be displayed for 3 seconds. To end auto-scan, press CHANNEL or MEMORY. To select a specific channel, press Channel. The following icons display based on the selected channel.

Kinetic Wave Icon

Designated	Indoor Display	Remote Display	Remote Display	Remote Display
Display		Channel 1	Channel 2	Channel 3

￿- Press to increase settings and activate

Trend line - Indicates the trend ofthe Atomic Clock signal reception. temperature and humidity.

Falling	Rising	Steady	￿ - Press to decrease
Current Temperature			the setting.
				MODE - Press to change
				display/settings.
Humidity Reading				3 - Press to view/change
				alarm settings.
MEMORY - Press to view
			CHANNEL - Press to switch
current or saved maximum
and minimum temperature or			to a different sensor.
humidity readings.