Changing the blade assembly, Tighten | Andis Company AG instruction

changing the blade assembly

If your clipper blades no longer cut properly (be sure to try more than one blade, since blade currently being used may be dull), it could be that your blade drive assembly needs replacement.

To change the blade drive assembly:

1. Unplug your clipper. 2. Remove blade set.

3. Remove four housing screws with philips screwdriver.

4.Turn clipper over and

remove cover.

5.Before attempting to

	remove the blade drive	SPRING
	assembly, you must	SPRING
	assembly, you must
	remove the blade hinge
	first. Remove the
	two blade hinge screws
	(Diagram H). When
	removing the blade hinge,	DIAGRAM I
	you will notice a small
	spring set in between
	the hinge and the lower
	housing (Diagram I).
	Make sure that this part
	does not get lost when
	replacing the blade drive
	assembly.

6. Remove blade drive mounting screws

(Diagram J).

7. NOTE: Before removing blade drive assembly, note the way it is posi- tioned (this will help you in reassembly). Remove blade drive assembly (Diagram K).

8.Drive bearing should be at its lowest position, if not, move it with your finger to lowest position (Diagrams L and M).

9.Align screw holes of new

blade drive assembly and

press down level at the screw holes (Diagram N).

10. Reassemble blade drive mounting screws (Diagram J).

11. Be sure the hinge spring is in its place before attempting to replace the

blade hinge and screws (Diagram O). When replac- ing the hinge screws, place screw in the screw hole and slowly turn counter-clockwise until

you feel the screw drop

into place. This assures the screw is properly aligned within the hole

threads. Turn screw clock- wise to tighten, just until snug. DO NOT OVER-

TIGHTEN.

12. Replace cover and turn clipper over.

13. Replace housing screws (Short screws in back by cord—long screws in front by blade).

DIAGRAM O

factory repair service

When the blades of your Andis Clipper become dull after repeated use, it is advised to send your blades to an Andis Authorized Service Station mentioned below for resharpen- ing. If you wish your clipper to be serviced as well, they should be carefully packed and mailed either Parcel Post Insured, or U.P.S.

To find an Authorized Service Station near you log on to www.andis.com or contact our customer service department: 1-800-558-9441 (U.S.) 1-800-335-4092 (Canada)

LIMITED WARRANTY

This Andis product is warranted against defective material or workmanship for one year from the date of purchase. All implied warranties arising and by virtue of State law shall also be limited to one year. Any Andis product determined to be defective in material or workmanship during the warranty period will be repaired or replaced without cost to the consumer for parts and labor. The defective product must be returned with proof of purchase and $6.50 to cover cost of handling, to any Authorized Andis Repair Station or to: Andis, 1800 Renaissance Blvd., P.O. Box 085005, Racine WI 53408-5005 USA or IN CANADA to: A & AG AGENCIES (CANADA), INC. 10050 Côte de Liesse, Lachine, Québec, H8T 1A3 CANADA. Enclose or attach a letter describing the nature of the problem. Due to foreign matter sometimes found in hair, clipper blades or resharpening of blades are not subject to the one year warranty. The blade set has a 10 Day Limited Warranty. If the blade set fails to cut, it will be resharpened free of charge if returned within 10 days of purchase. Send your blade set postage prepaid with the original purchase receipt to: ANDIS COMPANY, ATTENTION: Service Department, 1800 Renaissance Blvd, Sturtevant, Wisconsin 53177 (U.S. & Canada only). Andis will not be liable under this warranty for any defect, failure or malfunction of any of its products caused by normal wear, abuse, misuse, unauthorized adjustments or disassembling. Andis will not be liable for any consequential damages resulting from any defect in material or workmanship of any of its products. Some States do not allow limitations on how long an implied warranty lasts or exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you. The Warranty gives you specific legal rights, and you may also have other rights which may vary from State to State.

Date Purchased	Model	––––––––––––
–––––––––––––––––––		––––––––––––

Detachable Plus®

MODEL AG

Clipper

Andis Model AG Detachable Blades are compatible with Oster Model A5

Congratulations –

keep this for your records

you just went First Class when you bought this Andis Clipper. Careful workmanship and quality design have been the hallmarks of Andis products since 1922.

Form # 27074 Rev. P

Printed in U.S.A.