Pride Mobility INFMANU3267 I . D I S a S S E M B L Y a N D a S S E M B L Y, Frame Separation

Page 35

 

V I I . D I S A S S E M B L Y A N D A S S E M B L Y

7.

Unfasten the battery tie-down strap and remove

REAR LIGHTING

 

8.

the batteries from the battery wells.

HARNESS

 

Squeeze the tiller adjustment lever and lower

 

 

 

the tiller to its lowest point. Adjust the tiller

 

 

 

console if necessary.

 

 

 

WARNING! Failure to unplug both

 

 

 

battery harnesses, the front-to-rear

 

 

 

harness, and rear lighting harness

 

 

 

prior to separating the front and

 

 

 

rear sections could result in

 

 

 

permanent damage to the scooter.

 

 

Frame Separation

 

 

1.

Squeeze the tiller adjustment lever and lower

 

 

 

the tiller to its lowest point.

BATTERY HARNESSES

FRONT-TO-REAR HARNESS

2.

Lift up on the frame release lever. See figure 23.

3.

Lift the front section up until the frame hooks of

Figure 22. Harness Connections

 

the front section separate from the rear section.

 

 

 

 

See figure 24.

 

 

NOTE: Stabilize the rear section with your free

FRAME RELEASE LEVER

FRAME LOCK

 

 

hand by holding onto the upper frame tube. See

 

 

 

figure 24.

 

 

 

4. Slowly separate the two sections. See figure 24.

ASSEMBLY

 

1.

Position the front and rear sections of your

 

 

scooter as shown in figure 24.

 

2.

Use the frame release lever to lift the front sec-

 

 

tion as you align the frame hooks of the front

 

 

section with the lower frame tube of the rear

FRAME HOOK

 

section. See figure 23.

 

3.

Once the frame hooks are over the lower frame

Figure 23. Frame Release

 

tube, lower the front section completely. This

 

4.

will engage the frame lock. See figure 23.

LOWER FRAME TUBE

Raise the tiller.

UPPER FRAME TUBE

5.

Reinstall both batteries and secure with the tie-

 

 

down strap, making sure the strap is positioned over

 

 

the frame release lever to ensure proper securement.

 

6.

Connect the front-to-rear harness, rear lighting

 

 

harness, and both battery harnesses. See figure 22.

 

7.

Reinstall the rear shroud.

 

8.

Reinstall the seat and rotate it into place.

 

9.

Unlock the front wheel by turning the tiller lock

 

 

knob 90° counterclockwise. See figure 21A.

 

 

WARNING! After assembly, make

FRAME HOOK

 

absolutely certain the tiller lock

 

knob is in the unlocked position

Figure 24. Frame Separation

 

before riding your scooter.

Celebrity XL

www.pridemobility.com

35

Page 34 Page 36
Image 35
Page 34 Page 36
Contents Celebrity XL F E T Y G U I D E L I N E S N T E N T S Shipping and Delivery SafetyN T R O D U C T I O N PURCHASER’S AgreementS a F E T Y Product Safety SymbolsS a F E T Y S a F E T Y Modifications Removable Parts PRE-RIDE Safety CheckGeneral Incline Information Weight LimitationsTire Inflation Maximum Recommended Incline Angle Braking Information Cornering InformationCorrect Curb Approach Outdoor Driving SurfacesDoors Inclement Weather PrecautionsFreewheel Mode Stairs and EscalatorsBatteries Battery Disposal and RecyclingElevators LIFT/ELEVATION ProductsReaching and Bending Motor Vehicle TransportGetting Onto and OFF of Your Scooter ALCOHOL/SMOKING Positioning BeltsPrescription DRUGS/PHYSICAL Limitations Electromagnetic and Radio Frequency Interference EMI/RFI Tiller Console I . Y O U R S C O O T E RThrottle Control Lever Lights SwitchHazard Lights Switch Speed Adjustment DialManual Freewheel Lever Motor/Transaxle AssemblyBatteries Anti-tip WheelsMain Circuit Breaker Reset Button Safety Flag BracketInstallation Rear Securement Points Securement PointsCharging Your Batteries Reading Your Battery VoltageB a T T E R I E S a N D C H a R G I N G Batteries and ChargingFrequently Asked Questions FAQs How can I get maximum range or distance per charge? How can I ensure maximum battery life?What type and size of battery should I use? Battery Removal/Installation How do I change a battery in my scooter?What about public transportation? Why do my new batteries seem weak?Getting Onto Your Scooter PRE-RIDE Adjustments and ChecksP E R a T I O N Before Getting Onto Your ScooterGetting OFF Your Scooter Power Down Timer FeatureSeatback Adjustment Tiller Angle AdjustmentTiller Console Angle Adjustment Armrest Angle AdjustmentSeat Height Adjustment Seat Rotation AdjustmentFRONT-TO-BACK Seat Adjustment Positioning Belt Optional Mirror PositionTo operate the power seat Power Seat AdjustmentI . D I S a S S E M B L Y a N D a S S E M B L Y DisassemblyFrame Separation I . D I S a S S E M B L Y a N D a S S E M B L YWhat if all the systems on my scooter seem to be dead? I I . B a S I C TroubleshootingDiagnostic Beep Codes What if the main circuit breaker repeatedly trips? C a R E a N D M a I N T E N a N C E Wheel Replacement ABS Plastic Shrouds Wiring HarnessesNylon Lock NUT Replacement Fuse ReplacementDisposal of Your Scooter Storing Your ScooterA R R a N T Y Implied Warranties Warranty ExclusionsService Checks and Warranty Service Exclusions also include components with damage caused byP E N D I X I Specification S P E N D I X I Specification S T E S Page INFMANU3267
Top Page Image Contents