Sunrise Medical M11, F11 S e t U p , a d j u s t m e n t & U s e, IX. SET-UP, Adjustment & USE

Page 20

20

E n g l i s h

 

I X . S e t - U p , A d j u s t m e n t & U s e

IX. SET-UP, ADJUSTMENT & USE

NOTES:

1. Work Surface For Set-Up:

Use a flat surface, such as a table, to assemble, adjust and check your chair. This makes the steps easier and helps ensure a correct set-up.

2.Fasteners:

Many of the screws and bolts on this chair are special high-strength fasteners and may have special coatings.

Many nuts are of the Nylock type. They have a plastic insert to help prevent loosening.

1.Use of improper fasteners may cause the chair to fail.

2.Over- or under-tightened fasteners may fail or cause damage to chair parts.

3.If bolts or screws become loose, tighten them as soon as you can. Loose bolts or screws can cause damage to other chair parts causing them to fail.

3.Washers & Spacers:

Note the position of washers and spacers before disassembly.

To avoid damage to the frame, replace all washers and spacers when you reassemble parts.

4.Torque Settings:

A torque setting is the optimal tightening for a particular fastener. Use a torque wrench that measures 120 inch-pounds to secure screws, nuts and bolts on this chair.

NOTE– Unless otherwise noted, use a torque setting of 120 inch-pounds for all fasteners.

TOOLS YOU WILL NEED

1. Basic Tool Kit:

To set-up, adjust and maintain your chair you will need the following tools:

3mm Allen Wrench

5mm Allen Wrench

6mm Allen Wrench

8mm Allen Wrench

13mm Open-end Wrench

Phillips screwdriver #2

17mm Socket Wrench

You can obtain a multi-purpose tool kit from Sunrise, or buy the tools you need from a hardware store.

2. Torque Wrench:

If you plan to adjust and maintain this chair yourself, Sunrise recommends that you use a torque wrench.

NOTE– The wrench must measure inch-pounds. You can buy a torque wrench and proper sockets from a hardware store.

CHECK-OUT

Be sure this chair performs to your chosen operational settings. If it does not, turn the chair off immediately and reprogram with the Quickie QTronix Programmer. if you do not own a Quickie QTronix Programmer have your supplier reprogram your wheelchair as needed. Or, you can order a Quickie QTronix Pad for your own use, from your supplier.

NOTE– Repeat this procedure until the chair performs to your specifications.

When properly set up, this chair will operate smoothly. Check to see that all com- ponents work properly. If you detect a problem, be sure to correct it before use.

930756 Rev. B

Image 20
Contents Aspire N t r o d u c t i o n IntroductionSunrise Listens For Answers to Your QuestionsII. Table of Contents N t sIX. SET UP, Adjustment & USE T a b l e o f C o n t e n t sQuickie Aspire Choose the Right Chair & Safety Options Adjust Chair to Your AbilityT i c e R e a d B e f o r e U s e IV. NOTICE- Read Before USEWhat is EMI? EMI Electromagnetic InterferenceWhat Effect can EMI HAVE? Sources of EMIImmunity Level Report ALL Suspected EMI IncidentsWeight Limit Controller SettingsG e n e r a l W a r n i n g s Motor Vehicle Safety TerrainStreet USE Center of BalanceTransfers Reaching or LeaningIf YOU Must Reach or LEAN, do SO AT Your OWN Risk To Reduce The Risk Of a Fall Or Tip-OverDressing or Changing Clothes ObstaclesDriving in Reverse RAMPS, Slopes & SidehillsTo Reduce the Risk of a FALL, TIP-OVER or Loss of Control Ramps AT Home & WorkWheelchair Lifts Curbs & Single StepsStairs EscalatorsI . W a r n i n g s C o m p o n e n t s & O p t i o n s VII. Warnings Components & OptionsON/OFF Switch Motor LocksPneumatic Tires Positioning BeltsSuspension WiringUpholstery Fabric To Descend a Curb or Single Step E nTo Climb a Curb or Single Step IX. SET-UP, Adjustment & USE S e t U p , a d j u s t m e n t & U s eTools YOU will Need CHECK-OUTFootplate Adjustment S e t U p , a d j u s t m e n tT U p , a d j u s t m e n t & U s e Hanger Adapter OptionalSWING-AWAY Footrests Elevating Legrest OptionalBackrest Armrests AdjustmentSeat Height Adjustment Seat Removal Shroud RemovalPerformance Control Settings R aOperating Guide Quickie Qtronix Programmer PAD OptionalCircuit Breakers Joystick AssemblyE r a t i n g G u i d e Engage Motor Locks Battery Charger B a t t e r i e sXI. Batteries IntroductionConnecting Batteries in Battery Well Acid Burns Unsealed WET Cell BatteriesCharging Batteries Disposing of BatteriesXII. Maintenance CleaningBattery Maintenance Storage TipsI . M a i n t e n a n c e To Repair or Replace a TireMotor Brushes CorrosionCheck Maintenance ChartOrdering Parts I I . W i r i n g D i a g r a m XIII. Wiring DiagramWiring Diagram Detail Integrated Control System XIV. Sunrise Limited Warranty Quickie Aspire M11, F11
Related manuals
Manual 40 pages 50.37 Kb