Quantum 6000Z manual Seat Position, Manual Recline Seatback Adjustment, Seatback Angle Adjustment

Page 25

V . C O M F O R T A D J U S T M E N T S

10.Reinstall the retaining clips.

11.Reinstall the seat.

12.Reconnect the controller to the power base.

13.Reinstall the rear shroud and tighten the fasteners.

Seat Position

You can move the seat forward or rearward by chang- ing the extrusion mounting position.

To change the position:

1.Turn off the power to the controller.

2.Make sure the power chair is in drive mode.

3.Loosen the rear shroud fasteners and remove the rear shroud.

4.Unplug the controller connector(s) from the power base.

5.Remove the seat from the power base.

6.Remove both extrusions from the bottom of the seat.

7.Reposition the extrusions on a different set of mounting holes. You must move both extrusions the same number of holes either forward or back- wards. See figure 17.

8.Fasten the extrusions back onto the bottom of the seat.

9.Reinstall the seat.

10.Reconnect the controller to the power base.

11.Reinstall the rear shroud and tighten the fasteners.

Manual Recline Seatback Adjustment

If your power chair is equipped with a reclining seat, you can adjust the seatback angle with the seatback release lever. The lever is located on the right side of the seat base.

To adjust the recline angle:

1.Pull up on the seatback release lever.

2.Lean forward or backwards to the desired position.

3.Release the lever.

Seatback Angle Adjustment

If your power chair is equipped with an adjustable seat- back, you can adjust it to four (4) different angles: 90°, 102°, 105°, or 107°.

To adjust the seatback angle:

1.Remove the adjusting screws from each seat hinge.

See figure 18.

2.Set the seatback at the desired angle.

3.Reinstall the adjusting screws to each seat hinge and tighten.

SEAT MOUNTING

HOLES

Figure 17. Seat Position Adjustment

JAM NUT

ARMREST

ANGLE

ADJUSTING

SCREW

ARMREST

HEIGHT

ADJUSTING

SETSCREWS

SEATBACK ANGLE

ADJUSTING

SCREW

ARMREST KNOB

Figure 18. Seatback/Armrest Adjustment

Quantum 6000Z Series

www.pridemobility.com

25

Image 25
Contents Quantum Quick Reference Information F E T Y G U I D E L I N E SLanguage Usage IIIN T R O D U C T I O N SafetyPURCHASER’S Agreement Shipping and DeliveryS a F E T Y Product Safety SymbolsS a F E T Y S a F E T Y S a F E T Y General Guidelines Pre-Ride Safety CheckModifications Tire Inflation Weight LimitationsIncline Information Braking Information Freewheel ModeCornering Information Public Streets and Roadways Outdoor Driving Surfaces Inclement Weather PrecautionsStationary Obstacles Steps, Curbs, etc Doors Stairs and EscalatorsElevators Lift Systems/Elevation ProductsBatteries Positioning BeltsRemovable Parts Transfers Preventing Unintended Movement Reaching and BendingAlcohol/Smoking Prescription Drugs/Physical LimitationsQuantum 6000Z Series I . Y O U R P O W E R C H a I RSee figures 5, 6, Electrical Components Quantum 6000Z Series Power BaseQuantum 6000Z Series Electrical Components To operate the dual manual freewheel levers Dual Manual Freewheel LeversHammer Motor Package A S S E M B L Y Initial AssemblyTo install the seat Seat InstallationTo install the power seat Power Elevating Seat InstallationTransit Securement System Optional You may need the following to make comfort adjustments Comfort AdjustmentsSeat Height and Seat Angle Adjustment O M F O R T a D J U S T M E N T SSeatback Angle Adjustment Manual Recline Seatback AdjustmentSeat Position Armrest Height Adjustment Armrest Width AdjustmentArmrest Angle Adjustment Controller PositionFoot Platform Depth Adjustment Foot Platform Height AdjustmentTo adjust the foot platform depth To raise or lower the foot platformPositioning Belt Foot Platform Angle AdjustmentBatteries and Charging B a T T E R I E S a N D C H a R G I N GCharging the Batteries Frequently Asked Questions FAQs Battery Break-inHow often must I charge the batteries? Why do my new batteries seem weak?Daily Use Infrequent UseHow should I store my power chair and its batteries? How can I ensure maximum battery life?What about public transportation? What about shipping?Should your power chair come in contact with water Care and MaintenanceTemperature I . C a R E a N D M a I N T E N a N C EWeekly Checks Daily ChecksTo check the brakes Monthly ChecksCleaning and Disinfection Disposal of Your Power ChairWheel Replacement StorageQuantum 6000Z Series Drive Wheel Battery ReplacementI . C a R E a N D M a I N T E N a N C E Corrective Maintenance When to See Your Quantum Rehab Provider for ServiceTo replace the batteries Page Product Serial # Quality Control Quantum 6000Z Series
Related manuals
Manual 2 pages 24.44 Kb

6000Z specifications

The Quantum 6000Z represents a significant advancement in quantum computing, offering remarkable features that push the boundaries of what is possible in this revolutionary field. Designed with state-of-the-art technologies, it stands out due to its comprehensive architecture tailored for complex quantum calculations.

One of the key features of the Quantum 6000Z is its qubit design. Utilizing topological qubits, this system enhances error correction capabilities compared to traditional qubit systems. Topological qubits are more resistant to environmental disturbances, which is crucial for maintaining coherence during calculations. This innovation leads to increased stability and reliability in quantum computations, paving the way for longer computational tasks without significant error rates.

Another prominent technology integrated into the Quantum 6000Z is its advanced cryogenic cooling system. Operating at near absolute zero, this cooling mechanism minimizes thermal noise, optimizing qubit performance and ensuring the system functions effectively. The innovative cooling design contributes to the overall efficiency of the machine, allowing it to maintain optimal conditions for prolonged periods.

The Quantum 6000Z also boasts a highly scalable architecture, making it suitable for both small-scale laboratory experiments and large-scale industrial applications. With a modular design, users can easily upgrade or expand their systems as needed, promoting longevity and adaptability in an ever-evolving technological landscape. This scalability extends to software compatibility, as the Quantum 6000Z supports leading quantum programming languages, providing accessibility for developers and researchers alike.

In terms of connectivity, the Quantum 6000Z features an intuitive interface for seamless integration with existing computational infrastructures. This versatility allows organizations to harness quantum computing power without the need for an entire system overhaul. The built-in cloud access further enables users to run complex simulations and algorithms remotely, democratizing access to quantum technology.

Lastly, a key characteristic of the Quantum 6000Z is its focus on security. Quantum key distribution protocols are embedded into the architecture, providing a robust solution against cyber threats. This feature not only protects data during transmission but also establishes a pathway for secure communication channels in the post-quantum world.

In summary, the Quantum 6000Z stands at the forefront of the quantum computing revolution with its resilient qubit design, advanced cooling technologies, scalable architecture, and emphasis on security. Its capabilities promise to redefine industries, allowing for breakthroughs across sectors such as cryptography, materials science, and artificial intelligence.