Pride Mobility Quantum 1650 3SPVHD, Jazzy 1650 2EHD manual Seat Installation, To install the seat

Page 23

I V . A S S E M B L Y

Seat Installation

The Quantum Jazzy 1650 seat has four (4) seat towers that connect to the seat receivers on the power base frame. The seat towers have holes that enable you to adjust the seat height. Safety snap pins are inserted through the receiver and through the seat towers to secure the seat.

WARNING! Do not pick up the seat frame by the armrests. They are free to pivot, and you may lose control of the seat if they do so.

WARNING! Removing and installing your seating system should be accomplished by no fewer than two (2) people.

To install the seat:

1.Remove the safety snap pins.

2.Lift the seat over the power base.

3.Align each seat tower with the corresponding seat receiver. See figure 10.

4.Gently allow the seat to slide into each receiver until the seat is at the desired height.

5.Insert the safety snap pins into each seat receiver.

6.Install the armrests (if necessary). See figure 11.

7.Loosen the setscrews on the controller mount. See figures 10 and 14.

8.Slide the controller into the controller mount.

9.Tighten the setscrews to secure the controller.

10.Route the controller harness so that it cannot be pinched in the seat hinge.

MANDATORY! Prevent controller harness damage! Use correct tie-down points for controller harness. Avoid routing the controller harness on the outside of the armrest pad. Route the harness under the armrest or toward the inside of the armrest pad. Use correct tie-down points for the controller harness to prevent the harness from getting caught in the drive tires, pinched in the seat frame, or damaged when passing through doorways.

11.Use a wire tie to secure the controller harness to the armrest. See figure 10.

12.Plug the controller harness into the back of the controller and into the connector on the power base.

SEAT

WIRE TIE

TOWER

 

CONTROLLER

SEAT

MOUNT

 

RECEIVER

 

 

SAFETY

 

SNAP PIN

 

POWER BASE

Figure 10. Seat Installation/Removal (Typical)

Quantum Jazzy 1650 Series

www.pridemobility.com

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Quantum Quick Reference Information F E T Y G U I D E L I N E SIII N T E N T SShipping and Delivery SafetyN T R O D U C T I O N PURCHASER’S AgreementS a F E T Y Product Safety SymbolsS a F E T Y S a F E T Y S a F E T Y S a F E T Y Modifications Pre-Ride Safety CheckGeneral Guidelines Incline Information Weight LimitationsTire Inflation Cornering Information Freewheel ModeBraking Information Stationary Obstacles Steps, Curbs, etc Inclement Weather PrecautionsPublic Streets and Roadways Outdoor Driving Surfaces Lift/Elevation Products Stairs and EscalatorsDoors ElevatorsRemovable Parts Preventing Unintended Movement Motor Vehicle TransportPositioning Belts BatteriesTransfers Reaching and BendingElectromagnetic and Radio Frequency Interference EMI/RFI Prescription Drugs/Physical LimitationsAlcohol/Smoking I . Y O U R P O W E R C H a I R Quantum Jazzy 1650 Series Power ChairElectrical Components Quantum Jazzy 1650 Series Power BaseThermal Fuse To engage or disengage the drive motors Manual Freewheel LeversA S S E M B L Y Initial AssemblyTo install the seat Seat InstallationO M F O R T a D J U S T M E N T S Comfort AdjustmentsYou may need the following to make comfort adjustments Seat Height and Seat Angle AdjustmentHeavy Duty Drop-in Armrests Armrest Position AdjustmentArmrest Height Adjustment Controller Position Foot Platform Height AdjustmentFoot Platform Angle Adjustment Anti-Tip Wheels To adjust the forward/back positionTo adjust the leg rest length Heavy Duty Drop-in Leg RestsPositioning Belt To adjust the anti-tip wheelsTo install the positioning belt To adjust the positioning belt for operator comfortCharging the Batteries B a T T E R I E S a N D C H a R G I N GBatteries and Charging Frequently Asked Questions FAQs Battery Break-inHow can I get maximum range or distance per charge? Why do my new batteries seem weak?„ Daily Use „ Infrequent UseWhat about shipping? How can I ensure maximum battery life?How should I store my power chair and its batteries? What about public transportation?I . C a R E a N D M a I N T E N a N C E Care and MaintenanceShould your power chair come in contact with water TemperatureMonthly Checks Daily ChecksWeekly Checks To check the brakesYearly Checks Disposal of Your Power ChairCleaning and Disinfection Wheel ReplacementI . C a R E a N D Battery ReplacementTo replace the batteries Battery Wiring Diagram 4 BatteriesCorrective Maintenance When to See Your Quantum Rehab Provider for ServiceSpecifications P E N D I X I Specification SQuantum Jazzy 1650 Series Dimensions and Ground Clearance T E S T E S Product Serial # Quality Control Quantum Jazzy 1650 Series

Jazzy 1650 3EHD, Quantum 1650 3SPVHD, Jazzy 1650 2EHD, Quantum 1650 2SPVHD specifications

Pride Mobility has long been recognized as a leader in the field of mobility solutions, delivering products that enhance the quality of life for individuals with mobility challenges. Among its impressive lineup, the Jazzy and Quantum series stand out, particularly the Jazzy 1650 2EHD, Quantum 1650 2SPVHD, Quantum 1650 3SPVHD, and Jazzy 1650 3EHD models. Each of these powerchairs boasts innovative features and cutting-edge technology designed to ensure maximum comfort, safety, and maneuverability.

The Jazzy 1650 2EHD is designed for heavy-duty use, equipped with a robust frame capable of supporting users with a weight capacity of up to 600 pounds. This model features Enhanced Dual Drive technology, providing superior power and performance for tackling diverse terrains. Equipped with advanced suspension, the Jazzy 1650 2EHD offers a remarkably smooth ride, minimizing discomfort over uneven surfaces.

Meanwhile, the Quantum 1650 2SPVHD model showcases superior engineering tailored for exceptional performance and versatility. It is equipped with a patented Mid-Wheel 6 technology that ensures optimal maneuverability, allowing users to navigate tight spaces with ease. With its high-performance motor and heavy-duty components, this powerchair offers an impressive range, making it suitable for both indoor and outdoor use.

The Quantum 1650 3SPVHD elevates the user experience with additional enhancements such as advanced electronics and programmable options. This model not only supports a weight capacity of 600 pounds but also features a 3-speed control system, allowing users to adjust their pace according to their environment. Its sophisticated seating system provides enhanced comfort and adjustability, ensuring personalized support for users with diverse needs.

Lastly, the Jazzy 1650 3EHD takes mobility to the next level with features designed for both durability and sophistication. With its ergonomic design and quality materials, the Jazzy 1650 3EHD ensures that users not only enjoy functionality but also aesthetic appeal. The heavy-duty construction combined with superior performance gives users confidence while navigating various settings.

In conclusion, the Pride Mobility Jazzy and Quantum series, particularly the Jazzy 1650 2EHD, Quantum 1650 2SPVHD, Quantum 1650 3SPVHD, and Jazzy 1650 3EHD models, reflect the commitment to innovation in mobility solutions. With their combination of advanced technology, robust design, and user-centric features, these powerchairs provide individuals with the freedom and independence to lead a fulfilling life.
Top Page Image Contents