Oster Clipper Grease Instructions for Optimal Performance and Care

Page 1

Heavy-Duty Detachable

IMPORTANT SAFEGUARDS

Commercial Clipper • When using an electrical appliance, basic precautions should always be followed, including the following:

Read all instructions before using this appliance.

GETTING FAMILIAR WITH

YOUR CLIPPER

Due to continuous product improvement, product may vary slightly from

AVAILABLE OSTER® LUBRICANTS & CLEANERS,

& REPLACEMENT PARTS

Regular use of the following products will help you enjoy optimum performance from your

USING YOUR CLIPPER

Important:

• Before using your clipper, apply 1 or 2 drops of Oster® Clipper & Blade

Blade Clipper

Instruction Manual

For Commercial Use Only

Model 10 - 76010

DANGER

To reduce the risk of electric shock:

1.Do not reach for an appliance that has fallen into water. Unplug immediately.

2.Do not use while bathing or in a shower.

3.Do not place or store appliance where it can fall or be pulled into a tub or sink.

4.Do not place in or drop into water or other liquid.

5.Always unplug this appliance from the electrical outlet immediately after using.

6.Unplug this appliance before cleaning, putting on or taking off parts.

WARNING

To reduce the risk of burns, fire, electric shock, or injury to persons:

1.An appliance should never be left unattended when it is plugged in.

2.Close supervision is necessary when this appliance is used by, on, or near children or invalids.

3.Use this appliance only for its intended use as described in this manual. Do not use attachments not recommended by the manufacturer.

4.Never operate this appliance if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged, or dropped into water. Return the appliance to a service center for examination and repair.

5.Keep cord away from heated surfaces.

6.Never operate the appliance when air openings are blocked or while on a soft surface (such as a bed or couch).

7.Never drop or insert any object into opening.

8.Do not use outdoors or operate where aerosol spray products are being used or where oxygen is being administered.

9.Do not use this appliance with a damaged or broken comb or blade, as cut or scratched skin may occur.

10.To disconnect, move all controls to “OFF”, then remove plug from outlet.

11.Do not wrap cord around unit when storing. Continuous stress on the cord can damage cord insulation and result in a shock hazard.

12.Avoid contact with moving blades.

13.Avoid tangling or kinking the cord while clipping. Should the cord become tangled or kinked, stop clipping and straighten the cord.

what is illustrated.

1.Blade guard

2.Blade

3.Blade bracket

4.Blade hinge

5.Name plate/gear drive assembly access

6.Carbon brush cap/carbon brush

7.Oiler

8.Power cord

9.On/Off switch

10.Hanging ring

11.Cleaning Brush

12.Oster® Clipper & Blade Lube™ oil

13.Oster Gear Lube® grease

1

11

2

3/4

5

4

12

7

clipper and prolong its functionality.

Oster 5-in-1®

Kool Lube® 3

Spray

Blade Wash®

(076300-107)

76300-101

Disinfectant

Cleaning

All-purpose clipper

Lubricates and

76300-102

Solution 76300-

& blade lubricant

cools down blade.

Minimizes bacteria

103

and disinfectant.

 

 

buildup between

Flushes away

 

 

upper and lower

 

 

accumulated hair

 

 

blades.

 

 

and removes dirt

 

 

 

 

 

 

buildup trapped

 

 

 

between upper

 

 

 

and lower cutting

 

 

 

blades.

 

 

 

 

 

Lube™ Oil to the blade (refer to Taking Care of Your Clipper section).

For best results, hair should be clean and free from styling agents.

During use, apply Kool Lube® coolant occasionally to the blades to keep

 

them cool.

1.Plug unit into an AC electrical outlet.

2.Move On/Off switch to turn clipper on.

3.Remove blade guard.

4.Insert blade. Holding blade sides, slide blade bracket into hinge.

5.Push blade toward the clipper until it snaps into place

STEP 4

STEP 5

6.When finished clipping, turn clipper off and unplug cord from electrical outlet.

7.Cover blade with blade guard to keep it protected.

TAKING CARE OF YOUR CLIPPER

Note: Any other maintenance not explained in this manual must be per- formed by an Oster-Direct®Authorized Service Center.

Important: Make sure clipper is turned off and unplugged from electrical

10-76010_12EM1.indd 1

SAVE THESE INSTRUCTIONS

THE FOLLOWING PARAGRAPH IS FOR 120-VOLT MARKETS ONLY

To reduce the risk of electrical shock, this appliance has a polarized plug (one blade is wider than the other). This plug fits a polarized outlet only one way. This is a safety feature intended to help reduce the risk of electrical shock. If the plug does not fit fully into the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not attempt to defeat this safety feature.

ABOUT YOUR CLIPPER

Although your clipper has been thoroughly tested and inspected at every stage of its manufacturing and assembly, it is recommended that you lubri- cate it, as instructed in this manual, after 4-6 weeks of extensive use. This will ensure you obtain optimum performance and prolong the life of your clipper.

6

66

13

10

9

8

Blade Lube™

Gear Lube®

Replacement carbon brushes

Oil 76300-104

(076300-105)

(076917-710)

Lubricates between

Specially designed

Set of replacement carbon brushes and

upper and lower

to prolong the life of

springs

blades to keep

gears, bearings and

 

them sharper lon-

the motor.

 

ger and produce a

 

 

smoother clipping

 

 

action

 

 

To order any of these products, please call 1-800-830-3678 or visit www.osterstyle.com

outlet before removing, replacing or cleaning any parts. Lubricating Motor

If you hear a “squeal” or a dry bearing noise from the motor, it is a signal that the motor needs lubricating.

Remove cap from Oster® Clipper and Blade

APPLY 1

Lube™ tube and insert tip into oiler to apply 1

drop of oil. Be careful not to over lubricate.

DROP

Greasing Gear Drive Assembly

We recommend checking the gear drive assembly every six months for greasing.

Caution: Grease only when necessary as over-greasing may cause leakage and reduce clipper’s efficiency.

8/7/12 11:03 AM

Image 1
Contents What is illustrated Read all instructions before using this appliance76300-102 103What are the limits on JCS’s Liability? Warranty U.S. and Canada 1 Year Limited Warranty