Invacare 1160852 specifications Patient Height Specifications, Product Note

Page 1

Knee Walker

Assembly, Installation and Operating Instructions

SAVE THESE INSTRUCTIONS

NOTE: DEALER ‐ These instructions MUST be given to the user of this product.

NOTE: Check ALL parts for shipping damage. If shipping damage is noted, DO NOT use. Contact carrier/dealer for further instruction.

WARNING

DO NOT install or use this equipment without first reading and understanding this instruction sheet. If you are unable to understand the Warnings, Cautions or Instructions, contact a healthcare professional, dealer or technical personnel before attempting to install this equipment - otherwise, injury or damage may occur.

Each individual should ALWAYS consult with their physician or therapist to determine proper adjustment and usage.

A physical/occupational therapist should assist in the height adjustment of the knee walker for maximum support.

Care should be taken to ensure that all parts of the knee walker are secure and the casters are in good working order before use.

DO NOT sit on the knee walker. DO NOT use the knee walker as a wheelchair or transport device.

ALWAYS observe the weight limit on the labeling of your product. Check that all labels are present and legible. Replace if necessary.

If the push handle is exposed to extreme temperature (above 100°F or below 32°F), high humidity and/or becomes wet, prior to use, ensure the handgrip DOES NOT twist on the push handle - otherwise damage or injury may occur.

DO NOT attempt to reach objects that are out of your immediate reach while using this device. DO NOT reach for objects if you have to lean or shift position on the knee pad.

DO NOT hang anything from the frame of the knee walker. Items should be placed in the basket. Items should not protrude from the knee walker basket - otherwise, injury or damage may occur. The basket can hold up to 10 lbs.

ACCESSORIES WARNING

Invacare products are specifically designed and manufactured for use in conjunction with Invacare accessories. Accessories designed by other manufacturers have not been tested by Invacare and are not recommended for use with Invacare products.

Patient Height Specifications

MODEL

PATIENT HEIGHT MIN. / MAX

65960

5' 2" - 5' 10"

Product Note

The Knee Walker is designed to enhance user stability.

Installing the Rear Caster Assemblies

NOTE: For this procedure, refer to FIGURE 1.

NOTE: To remove the rear caster assemblies, reverse this procedure.

1.Remove the plastic from around the rear casters.

2.Press the snap buttons on the rear caster tube.

NOTE: When installed properly, the caster and brakes will face outward.

3.Insert the rear caster tube into the frame tube and slide the snap buttons to one of five height adjustment holes.

NOTE: There will be an audible “click”.

4. Install the other rear caster assembly into the opposite frame tube.

Installing the Front Casters

NOTE: For this procedure, refer to FIGURE 1.

NOTE: To remove the front casters, reverse this procedure.

1.Remove the plastic from around the front casters.

2.Press the snap buttons on the front caster tube.

NOTE: The front caster with the colored marking MUST be installed on the same side of the knee walker as the user’s injury.

Height

Adjustment

Holes

 

 

 

 

 

 

 

 

 

 

Knee Pad

 

 

 

 

 

 

 

 

 

 

Colored

 

 

Height

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Marking

 

 

 

 

 

 

 

 

 

 

 

 

 

Adjustment

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Front

 

 

Holes

 

 

 

 

 

 

 

 

 

 

 

Caster

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CAUTION

The front caster with the colored marking MUST be installed on the same side as the user’s injury. The front casters MUST be adjusted to the same height adjustment hole that the rear caster assemblies are adjusted to.

3.Insert the front caster with the colored marking into the frame tube on the same side as the user’s injury. Slide the snap buttons to the same height adjustment hole as the rear caster assemblies.

NOTE: There will be an audible “click”.

4. Install the other front caster into the opposite frame tube.

Adjusting the Knee Walker Height

NOTE: For this procedure, refer to FIGURE 1.

1.Press the snap buttons on the caster tube.

2.Slide the snap button to one of five height adjustment holes. NOTE: There will be an audible “click”.

CAUTION

The front casters MUST be adjusted to the same height adjustment hole that the rear caster assemblies are adjusted to.

3. Adjust the front and rear caster assemblies to the same height.

Rear Caster Assembly

(caster and brake on the

outside of the knee walker)

FIGURE 1 Assembling the Knee Walker

For more information regarding Invacare products, parts, and services, please visit www.invacare.com

 

 

 

 

Part No 1160852

1

Knee Walker

Image 1
Contents Installing the Rear Caster Assemblies Patient Height SpecificationsInstalling the Front Casters Adjusting the Knee Walker HeightInstalling/Removing the Basket Installing/Adjusting the Push HandleUsing the Knee Walker Care and MaintenanceLimited Warranty One Invacare Way USA