Electrical Specifications Outdoor only

ELECTRICAL SPECIFICATIONS (OUTDOOR ONLY):

!Power 24VAC, Class 2 Only

52 watts at 24 VAC (Heater & Blower) Accessory Power Heater: 50 watts

Blower: 1.7 watts

13 watts Camera Power (models WV-CS954 & WV-CS574) Input Connectors (outdoor units):

BNC

(2)4 position Molex connectors (power)

(1)Phone style plug (control)

NOTE: This unit is designed for operation in an upright position. Installing the unit upside down may cause damage to the internal equipment, and will void the warranty.

GENERAL INSTRUCTIONS FOR MOUNTING HOUSING

INSTALLING PENDANT MOUNT (POD9CW/POD9CFW)

1.This unit includes a 1 1/2" NPT coupling for a standard 1 1/2" NPT pipe. The POD9 can be used with other brackets designed with 1 1/2" male pipe threads, such as the Panasonic PWM20G and PWM30G wall mount brackets.

2.Attach the housing coupling (Figure 2).

NOTE: Pipe threads should be clean and rust free. Use a sealer (such as Teflon™ tape or silicone sealer) on the threads.

Add thread sealing tape

Figure 2

INSTALLING THE HOUSING ASSEMBLY FOR WALL MOUNT POD9CW/POD9CFW

1.A wall mount bracket comes standard with this unit, and a template is included to use as a guide for mounting the bracket to a wall. Choose the desired location for installation and mark the drill holes using the template.

NOTE: Be sure the hardware and the mounting surface can sup- port the weight of the wall mount bracket plus the weight of the housing and drive unit. The load will be subjected to vibration from the camera motor and wind.

2.The wall mount bracket provided with the POD9CW includes a location for conduit entry. If you wish to install conduit to the bracket remove the conduit hole plug. Install fitting from below the wall mount and secure with conduit nut from inside the bracket.

3.Open the access door on the bottom of the wall mount by loosening the screw nearest the mounting plate (Figure 1).

1.Mount the housing assembly to the mounting bracket and housing coupling. A safety cable is included with the housing to temporarily hold it while making wiring connections. Loop the safety cable over one of the set screws on the housing coupling and make the appropriate connections using the wiring chart supplied on Page 4.

Make sure set screw is secure before hanging housing from screw

Figure 3

2.Upon completing wiring, undo the safety cable and twist the housing onto the housing coupling. Secure all (3) setscrews provided on the housing coupling (Figure 4).

Access panel

Figure 1

4.Attach the wires from the wall to the connector provided, using the wiring color code chart as a guide.

5.Once all wiring connections are made, place the wires inside the wall mount bracket and close the access door. Secure with the screw removed earlier.

6. Clean the outside of the dome.	- -

Set screws

Figure 4

3. Clean the outside of the dome.

POD9CF(W), Pod9cw specifications

The Panasonic Pod9cw and POD9CF(W) are innovative solutions in the realm of compact, energy-efficient cooling systems. Tailored for both residential and commercial applications, these units are designed to provide optimal comfort without compromising performance or energy savings.

One of the primary features of the Pod9cw and POD9CF(W) is their impressive energy efficiency. With advanced inverter technology, these units can adjust their cooling output based on the desired temperature, which not only enhances comfort but also significantly reduces electricity consumption. The energy-efficient design is complemented by a high Seasonal Energy Efficiency Ratio (SEER), making them an environmentally friendly choice for anyone looking to minimize their carbon footprint.

In terms of design, the Pod9cw model boasts a sleek, modern look that integrates seamlessly into any environment. The compact size and lightweight construction ensure that installation is straightforward, even in tight spaces. The POD9CF(W), on the other hand, features an elegant white finish, making it an ideal choice for both contemporary and traditional interiors.

The advanced air filtration system included in both models is another notable feature. Equipped with a multi-layer filter, these units not only cool the air but also purify it by trapping dust, allergens, and other airborne particles. This ensures that the indoor environment remains fresh and healthy, making it particularly suitable for homes with children or individuals with respiratory issues.

Noise reduction technology is a highlight of the Pod9cw and POD9CF(W). Both models operate quietly, allowing for a peaceful environment in homes, offices, or commercial spaces. The low-noise performance is achieved without sacrificing cooling efficiency, ensuring that users remain comfortable without disruptive background noise.

Additionally, both systems come with intuitive control options. The smart control interfaces allow users to easily set and adjust the temperature, fan speed, and operational modes from a user-friendly panel. Some models also offer remote control capabilities, enabling users to manage their cooling preferences from anywhere in the room.

In summary, the Panasonic Pod9cw and POD9CF(W) represent a sophisticated blend of technology, efficiency, and functionality. Their energy-saving features, stylish design, effective air purification, and quiet operation make them a standout choice for anyone in need of reliable cooling solutions. Whether for a cozy residential setup or a bustling commercial space, these systems are engineered to meet diverse climate control needs while ensuring a reduced environmental impact.