Multiquip manual WC-42S Concrete Mixer Mixer Basic Components

Page 13

WC-42S CONCRETE MIXER — MIXER BASIC COMPONENTS

Figure 2. Mixer Major Components

1.Steel Mixing Drum — The MQWhitemanWC-42S uses a 4 cu. ft steel mixing drum. This drum is to be used for mixing of concrete. Always clean the drum after each use. DO NOT use this mixing drum for the mixing of volatile liquids.

2.Dump Latch — To rotate the mixing drum, this latch must be in the up position.To lock the drum, place the latch in the down position.

3.Dump Gear Guard NEVER operate the mixer with this guard removed. Its purpose is to prevent dirt and debris from entering the dump gear. In addition operator clothing could become entangled in the dump gear, causing severe injury and bodily harm.

4.Handwheel — Turn this wheel clockwise or counter- clockwise to rotate the mixing drum. Remember the dump latch must be in the up position in order for the mixing drum to be rotated.

5.Zerk Fittings — There is, at the bottom and engine side of the yoke, and center of the handwheel grease zerk fittings. Lubricate these fittings as referenced in the maintenance section of this manual.

6.Safety Chain — This mixer uses a 3/16-inch thick, 72- inches long zinc-plated saftey chain. ALWAYS connect the safety chain when towing.

7.Tow Bar — This mixer uses various towing bars, please reference the frame assembly drawing and parts list in this manual to determine which tow bar meets your requirements.

8.Leaf Suspension — This mixer uses a leaf type suspension. Check the mounting hardware for bolt hole elongation and tightness. See maintenance section of this manual for recommended maintenance.

9.Chock Blocks — Place these blocks (not included as part of the mixer package) under each mixer wheel to prevent rolling, when mixer is not connect to the towing vehicle.

10.Tires Ply — The tire ply (layers) number is rated in letters; This mixer uses 13-inch 2-ply tires. Replace with only recommended type tires.

11.ON/OFF Switch (gasoline only) —This switch is provided on mixerwith gasoline engines only and is located on the side of the mixer frame. When activated it will shut down the engine. Pull out when starting the engine.

12.Cabinet/Latch — Encloses engine and electric motor. NEVER run mixer with cabinet removed. Use latches to secure engine compartment cabinet.

13.Mixing Blades (Steel) — Used for the mixing of concrete. When blades show signs of wear, entire steel mixing drum assembly must be replaced. See steel mixing drum assembly in the parts section of this manual.

WC-42S CONCRETE MIXER — PARTS & OPERATION MANUAL — REV. #8 (12/16/05) — PAGE 13

Image 13
Contents Whiteman Series Concrete Mixer Page Heres HOW to GET Help WC-42S Concrete Mixer Table of Contents Warranty Department Service DepartmentParts Department Technical AssistanceBaldor 34F324-5596 ModelWC-42S Concrete Mixer Dimensions Mixer Foryour Safety and the Safety of Others WC-42S Concrete Mixer Safety Message Alert SymbolsWC-42S Concrete Mixer Rules for Safe Operation Emergencies WC-42S Concrete Mixer Rules for Safe OperationWC-42S Mixer Decals Machine Safety DecalsWC-42S Concrete Mixer General Information WC-42S Concrete Mixer Mixer Basic Components Starting, OFF position stops engine operations WC-42S Concrete Mixer Basic Engine ComponentsHandwheel Assembly AssemblyMixer Tow Bar Vehicle Connection Pentile and Loop Tow Bar to Vehicle Connection Coupler OnlyTow Bar to Mixer Connection Tow Bar and Safety Chain InstallationElectric Motor Connection Electric MotorWC-42S Concrete Mixer Electric Motor Single Phase Electric Motor with 12 inch Pigtail CableWC-42S Concrete Mixer PRE-INSPECTION GAS Engine Fuel Shut-OFF Lever Starting the Engine Gasoline OnlyStarting the Electric Motor Initial Start-up Instructions Electric Motor StartingOperation WC-42S Concrete Mixer OperationStopping the Mixer Electric WC-42S Concrete Mixer Maintenance Engine Maintenance WC-42S Concrete Mixer Maintenance EngineWC-42S Concrete Mixer Maintenance Mixer Suspension Components WC-42S Concrete Mixer Maintenance MixerTo tighten wheel lug nuts Page Engine Troubleshooting WC-42S Concrete Mixer Troubleshooting EngineWC-42S Concrete Mixer Troubleshooting ENG./MIXER Items Found In the Remarks Column Explanation of Code in Remarks ColumnWC-42S Concrete Mixer Suggested Spare Parts Name Plate and Decals See Operation and Safety Decals DECAL, Safety InstructionsDECAL, MQ Whiteman Logo CIPDCL160 DECAL, Crush Warning DECAL, Emergency StopSteel Barrel Assy CAP Housing JackshaftKing PIN Ring GearMain Frame Assy GUARD, Gear Wheel Connector LinkWASHER, Lock 1/4 Dump GearAxle Assy OIL Seal Lock NUT 5/8 NCBearing CONE, 7/8 Spindle Bearing CONE, 1-1/16 SpindleCabinet Assy WASHER, Flat 5/16 Rubber Protector Includes Item WLatch ASSY., Complete WASHER, Lock 5/16GAS Engine Mounting Plate Assy RING, Retaining ENGINE, Honda 4.0 HPSquare KEY Upper PulleyElectric Motor Mounting Plate Assy Drive Pulley MOTOR, Electric .5 HPAIR Cleaner Assy COLLAR, AIR Cleaner GROMMET, AIR CleanerCollar B, AIR Cleaner GASKET, ElbowCamshaft Assy ROD, Push SPRING, Weight ReturnARM, Valve Rocker LIFTER, ValveCarburetor Assy Gasket SET PLATE, Lever SettingValve SET, Float Float SETControl Assy ROD, Governor ARM, GovernorSPRING, Governor SPRING, Throttle ReturnCrankcase Cover Assy GASKET, OIL Filler CAP GASKET, Case CoverBEARING, Radial Ball PIN A, DowelCrankshaft Assy CRANKSHAFT, H-TYPE Cylinder Barrel Assy PIN, Governor Weight WEIGHT, GovernorSLIDER, Governor SHAFT, Governor ARMCylinder Head Assy CLIP, Valve Guide GUIDE, Valve OS OptionalGASKET, Cylinder Head COVER, HeadFAN Cover Assy WIRE, Stop Switch 370MM GROMMET, Adjusting CoverCOVER, FAN *NH1* Black PLATE, Side OIL AlertFlywheel Assy PULLEY, Starter FAN, CoolingFlywheel NUT, Special 14MMFuel Tank Assy JOINT, Fuel Tank RUBBER, Supporter 107MMTANK, Fuel *NH1* Black GASKET, Fuel Filler CAPIgnition Coil Assy Coil ASSEMBLY, Ignition Muffler Assy PROTECTOR, Muffler MufflerGASKET, Muffler SCREW, TappingPiston Assy Ring SET, Piston Standard BOLT, Connecting RODPISTON, Standard PISTON, OSRecoil Starter Assy REEL, Recoil Starter SCREW, SettingRATCHET, Starter GUIDE, RatchetNo Artwork Available Gasket KIT Assy Honda GX120K1QX2 Engine Gasket KIT AssyEngine Labels Assy Label Caution Labels AssyMark Choke MARK, OIL AlertEffective October 1, 2002 Terms and Conditions of Sale Parts Page Multiquip INC

WC-42S specifications

The Multiquip WC-42S is a versatile and robust walk-behind concrete saw, specifically designed for precision cutting and user efficiency. This machine is particularly beneficial to contractors involved in the construction and maintenance of roads, pavements, and other concrete structures. Its durability and high-performance specifications make it a popular choice for both commercial and residential projects.

One of the standout features of the WC-42S is its powerful engine. Powered by a reliable Honda GX390 engine, the saw offers impressive performance, delivering ample power for both wet and dry cutting applications. The engine's fuel efficiency ensures longer operational periods, minimizing downtime for refueling, and its ease of use is a significant advantage for operators of all skill levels.

The WC-42S is equipped with a robust cutting assembly that accommodates a variety of blade sizes, with a maximum cutting depth of up to 4 inches. This adaptability allows users to customize their operations according to specific project requirements. The machine can support blades up to 14 inches in diameter, offering added versatility for various cutting tasks across different materials, including asphalt and reinforced concrete.

A notable technological feature of the WC-42S is its inflexible frame design, which enhances stability and support, ensuring straight cuts even under demanding conditions. The saw also features a user-friendly depth adjustment system that allows for quick changes between cutting depths, providing operators with unparalleled control.

Safety and comfort have also been prioritized in the design of the WC-42S. It is fitted with ergonomic handles that reduce operator fatigue during prolonged use. The saw’s low-profile design allows for better visibility and control, particularly when cutting in tight spaces or intricate patterns.

Moreover, the WC-42S includes an integrated water system for cooling the blade and minimizing dust, contributing to cleaner worksite conditions. This feature not only enhances performance but also improves operator safety by reducing silica dust exposure.

In summary, the Multiquip WC-42S walk-behind concrete saw stands out with its powerful engine, versatile cutting capabilities, user-friendly design, and integrated safety features. Its blend of technology and robust engineering makes it a favorite among professionals looking for reliability and high performance in concrete cutting solutions. With the WC-42S, contractors can achieve precise cuts efficiently and effectively, making it a worthy investment for any concrete project.