GM MANTS420 manual Operating Modes, Calibration

Page 20

Model TS420

4.2Operating Modes

The TS420 has four distinct operating modes: Start-up, Normal Operation, Calibration and Fault. The mode is indicated by both the analog output and the LCD display. See Figures 5 and 6.

4.3Calibration

Activating the “CAL” switch will automatically disable the external alarm circuits by fixing the analog output current to 3.75mA.

General Monitors recommends that the TS420 be calibrated within the first twenty-four (24) hours after initial start-up, and that calibration be checked at least every ninety (90) days to ensure the integrity of the system.

NOTE: A calibration check consists of applying a 20.9% V/V O2 (“normal” ambient air) of full- scale concentration of gas to the sensor and observing the reading on the display device being used.

General Monitors is not implying that the customer should expect problems with sensor life or stability. “Frequent” calibration checks merely ensure the integrity of the life protecting equipment, and are recommended for problem environments (i.e. sensors accidentally being painted over, etc, see Appendix 5.4).

A calibration schedule should be established and followed. A logbook should also be kept showing calibration dates and dates of sensor replacement.

Calibration Procedure:

1.If it is suspected that the air is not at “normal” levels (20.9% O2), it will be necessary to calibrate the sensor with clean air. The 20.9% O2 gas cylinder (GMI P/N 1400262-11) can be used. Apply the clean air source prior to entering calibration mode and allow the sensor to stabilize for at least one (1) minute before proceeding.

2.Place the magnet over the GMI Logo on the body of the unit and hold it there until the “CAL” LCD indicator appears, then remove the magnet. The analog output current will drop to 3.75mA.

4. The “CAL” and “MODE” LCD indicator will flash, indicating that the unit is now calibrating.

4.After approximately 30 seconds, the display will change from a flashing “CAL” and “MODE” LCD to a solid “MODE” LCD, indicating that the calibration is complete and the unit has re- entered “OPERATE” mode. Remove any calibration gas.

6.The unit is now calibrated and the new values have been stored in the NOVRAM (non- volatile memory).

Figure 6 shows a flow diagram of the codes that will appear in the display window during the calibration procedure.

If there is a problem and the TS420 cannot complete the calibration sequence, a fault indicator will be displayed, and the analog output current will drop to 3.5mA.

9

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Model TS420 Warranty Statement Commissioning Safety Systems System Integrity VerificationPeriodic Testing/Calibration of Field Devices Periodic System VerificationMount and Wire the Detector pages 5 through Figure Q-A Outline and Dimensional DrawingFigure Q-B Wiring Diagram Intrinsically Safe BarriersPower-up After Initial Calibration Apply power to the detectorInitial Power-up Calibration Procedure Calibrate the DetectorViii Table of Contents Table of Figures Plastic Junction Box, NPT 45160-2 Plastic Junction Box, M20Features and Benefits IntroductionGeneral Description ApplicationsThis page left intentionally blank Detector Assembly Sensor AssemblyControl Electronics LCD Display LocationDetector Location Considerations InstallationReceipt of Equipment Installation Instructions MaintenanceWiring Connections Wiring DiagramApplying Power OperationOperating Modes CalibrationFlow Diagram Calibration EquipmentSensor Replacement Procedure Sensor Alignment Remove paper liner from gasket, if present Fault Codes are Sensor Care and MaintenanceFault Codes & The Remedies Specifications AppendixInput Power Status IndicatorEnvironmental Specifications Operating Temperature Range Storage Temperature RangeIntrinsically Safe System Requirements CapacitanceInductance Sample CalculationØ1.75 2-20 UN-2A Outline & Dimensional Drawing NPTEngineering Documentation Control Drawing Sample Installation Safearea10252 Round Aluminum Junction Box 31305-2 Aluminum Junction Box70631-2 Splash Guard Accessories Calibration AccessoriesOrdering Information Calibration Schedule for Problem Environments Spare Parts & Accessories

MANTS420, TS420 specifications

The GM TS420 and MANTS420 represent a breakthrough in agricultural technology tailored for enhancing both efficiency and productivity in farming operations. As versatile solutions, they are designed to meet the demands of contemporary agricultural practices.

One of the primary features of the GM TS420 is its powerful engine, which ensures robust performance across various terrains. The engine is specifically engineered to provide optimal fuel efficiency while minimizing emissions, aligning with modern environmental standards. This is crucial for farmers focused on maintaining a sustainable operation while reducing operational costs.

The MANTS420, on the other hand, stands out for its advanced precision farming technologies. Equipped with cutting-edge GPS and navigation systems, the MANTS420 allows for precise planting and harvesting. This precision is essential for maximizing yields and minimizing waste, as it enables farmers to apply inputs such as seeds, fertilizers, and pesticides more effectively and economically.

Both models feature a user-friendly interface, which streamlines operation and reduces the learning curve for new users. The touchscreen displays provide real-time data on machine performance, field conditions, and crop status, allowing farmers to make informed decisions quickly and efficiently.

In terms of durability, the GM TS420 and MANTS420 are built with high-quality materials designed to withstand the rigors of agricultural environments. Their sturdy chassis and high-ground clearance enhance maneuverability in challenging landscapes, making them ideal for diverse farming tasks.

Furthermore, the technology in both units includes telemetry and remote monitoring capabilities. This allows farmers to track performance metrics and receive maintenance alerts, minimizing downtimes and optimizing machine longevity.

The implement compatibility of the GM TS420 and MANTS420 is another noteworthy characteristic. Both models can accommodate a wide range of attachments, making them versatile tools for various agricultural tasks, from tilling and plowing to seeding and harvesting.

In conclusion, the GM TS420 and MANTS420 embody the synthesis of advanced engineering and technology in the agricultural sector. Their combination of robust power, precision farming capabilities, ease of use, durability, and versatility make them indispensable assets for modern farmers seeking to enhance productivity while adhering to sustainable practices.
Top Page Image Contents