MTP 15HD RS Series • Setup Guide
|
|
|
|
| ANT: | complete | ||||
|
|
|
| T |
| the | ||||
| IMPOR.com | for |
| and | ||||||
| instructions, |
| ||||||||
| .extr |
|
|
|
| |||||
to |
| on |
|
|
|
| the | |||
,installationoreconnectingce |
| |||||||||
| www |
|
|
|
|
|
|
| . |
|
Go guide |
| bef |
|
| wersour |
| ||||
user |
|
|
| the | po |
|
|
| ||
specifications |
|
|
|
|
|
|
| |||
| product | to |
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
This card provides quick start instructions for an experienced installer to set up and operate any of the MTP VGA video and RS‑232 transmission systems.
Pre-installation — RS-232 Jumper
The receiver’s RS‑232 circuits are
Installation
Step 1 — Mounting
Unjumpered for
JMP3
JMP2
JMP1
Jumpered for
Turn off or disconnect all equipment power sources and mount the MTP transmitter and up to eight receivers as required.
Step 2 — Transmitter Inputs
•Connect a computer (VGA) video source to the Input connector.
•Connect a VGA monitor to the Monitor connector.
•Plug an
Connected | Receive | Tx | MTP | |
Transmit | Rx | |||
Pins | ||||
Device Pins | Ground | Gnd | ||
|
Step 3 — TP Cables Between Units
•Terminate a TP cable as shown at right. Connect it between the transmitter’s Output port and the receiver’s Input port (both ends must match).
NOTE: If the unit is labeled “C7,” only CAT 7 cable should be used.
•For
Tx Rx |
|
|
| INPUT |
| MONITOR | ||||
|
| Pins: |
|
|
|
| |||
12345678 |
|
| Pin | T568A |
| T568B | |||
|
|
|
|
|
| Wire Color |
| Wire Color | |
|
|
|
|
|
| ||||
|
|
|
|
|
| 1 |
| ||
|
|
|
|
|
| ||||
|
|
|
|
|
| 2 | Green |
| Orange |
|
|
|
|
|
| ||||
|
|
|
|
|
| 3 |
| ||
|
|
|
|
|
| 4 | Blue |
| Blue |
|
|
|
|
|
| ||||
|
|
|
|
|
| 5 |
| ||
|
|
|
|
|
| 6 | Orange |
| Green |
|
|
|
|
|
| 7 |
| ||
Insert Twisted | 8 | Brown |
| Brown | |||||
|
|
|
| ||||||
|
|
|
| ||||||
| Pair Wires |
|
|
|
|
NOTE: If you are using Enhanced
Step 4 — Receiver Outputs
•Connect a VGA monitor to the Output connector.
•Plug an
Tx Rx
OUTPUT
Step 5 — Receiver DIP Switches
•H Sync and V. Sync switches — Set these switches up for positive sync or down for negative sync.
•Composite Sync, (SOG), and Video switches — Set these switches as shown in the following table to output the indicated format.
Output Format | C Sync | SOG | Video |
|
|
|
|
|
|
|
|
RGBHV | | | |
RGBS | | | |
RGsB | | | |
Component* | | | |
| | | |
Composite* | | | |
NOTE: * Input video format must match.
•End Unit switch — Set this switch up if either of the following is true:
•The receiver being configured is the only receiver connected to the transmitter.
•The receiver being configured is the last receiver in a
H SYNC + V SYNC + C SYNC SOG VIDEO END UNIT
ON
1 2 3 4 5 6