Mounting on Door Mounting on Window | Linear DXT-31 specification

MOUNTING ON DOOR

MOUNTING ON WINDOW

MOUNT PLATE

TO FRAME

1/2" MAXIMUM SPACE BETWEEN TRANSMITTER AND MAGNET PLATES

SNAP TRANSMITTER ONTO MOUNTING PLATE

ALIGN MAGNET PLATE NEXT TO TRANSMITTER PLATE AND ATTACH TO DOOR

MOUNT TRANSMITTER

PLATE TO FRAME

SPACE BELOW

PLATE IS REQUIRED

TO SNAP TRANSMITTER

ONTO PLATE

1/2" MINIMUM

SNAP TRANSMITTER ONTO MOUNTING PLATE

ALIGN MAGNET PLATE NEXT TO TRANSMITTER PLATE AND ATTACH TO WINDOW

OPTIONAL MAGNET SPACER

FOUR HEIGHT

POSITIONS

USE SNAP-ON MAGNET

SPACER WHEN MORE

HEIGHT IS REQUIRED

SQUEEZE SIDE TABS

TO ADJUST MAGNET

HEIGHT

HOOK SPACER TO

MAGNET PLATE

AND ROTATE TO

LOCK IN PLACE

OPTION JUMPER POSITIONS

SELECTS INTERNAL	SELECTS EXTERNAL
SWITCH	SWITCH
(INSIDE POSITION)	(MIDDLE POSITION)

	SELECTS GLASS	SELECTS BOTH
		INTERNAL AND
	BREAK SENSOR ONLY
		EXTERNAL SWITCHES
	(EDGE POSITION)
		(NO JUMPER)

NOTE: GLASS BREAK INPUT

TERMINALS ARE ALWAYS ACTIVE

CONNECTING EXTERNAL CONTACTS

WIRE EXTERNAL NORMALLY

	CLOSED CONTACTS TO	THIS IS THE FACTORY SET
		JUMPER POSITION IT SELECTS
	TERMINALS 1 & 2
		THE INTERNAL SWITCH

PUT JUMPER ON THE MIDDLE PINS TO USE EXTERNAL SWITCH

- OR -

CONNECTING EXTERNAL GLASS BREAK SENSOR

MOVE JUMPER FROM

THESE PINS (SELECTS

CONNECT NORMALLY OPENINTERNAL SWITCH)

GLASS BREAK SENSOR

WIRES TO TERMINALS 2 & 3

TO THESE PINS

(SELECTS GLASS

ROUTE SENSORBREAK SENSOR) WIRES UP THROUGH

WIRING SLOT

IMPORTANT NOTE:	TAKE JUMPER
IMPORTANT NOTE:	OFF TO USE
WHEN USING BOTH	BOTH
INTERNAL AND EXTERNAL	EXTERNAL
SWITCHES BOTH SWITCHES MUST	& INTERNAL
BE CLOSED TO ARM THE TRANSMITTER	SWITCH

NOTE: THIS TRANSMITTER IS DESIGNED FOR USE WITH THE UNITED SECURITY PRODUCTS "WINDOW BUG" GLASS BREAK SENSOR. OTHER SENSORS HAVE NOT BEEN TESTED.

CHANGING BATTERIES

WHEN BATTERIES ARE LOW, OPEN SENSOR CASE AND GENTLY LIFT UP END OF BATTERY CLAMP,

SLIDE BATTERIES OUT

NOTE: USE OF EXCESSIVE FORCE ON

BATTERY CLAMP WILL RESULT IN DAMAGE

LINEAR LIMITED WARRANTY

This Linear product is warranted against defects in material and workmanship for twelve (12) months. The Warranty Expiration Date is labeled on the product. This warranty extends only to wholesale customers who buy direct from Linear or through Linear’s normal distribution channels. Linear does not warrant this product to consumers. Consumers should inquire from their selling dealer as to the nature of the dealer’s warranty, if any. There are no obligations or liabilities on the part of Linear corporation for consequential damages arising out of or in connection with use or performance of this product or other indirect damages with respect to loss of property, revenue, or profit, or cost of removal, installation, or reinstallation. All implied warranties, including implied warranties for merchantability and implied warranties for fitness, are valid only until Warranty Expiration Date as labeled on the product. This Linear Corporation Warranty is in lieu of all other warranties express or implied.

For warranty service on Linear equipment return product, at sender’s expense to: Linear Corporation Repairs Department

LIFT

REMOVE BATTERIES

IF NECESSARYFROM THIS END PUSH IN SLOT TO REMOVE

SENSOR FROM MOUNTING PLATE

INSTALL TWO DURACELL TYPE DL 2032 BATTERIES (+)

SIDE UP

2580 Pioneer Avenue, Suite C

Vista, CA 92083

IMPORTANT !!!

Linear radio controls provide a reliable communications link and fill an important need in portable wireless signalling. However, there are some limitations which must be observed.

For U.S. installations only: The radios are required to comply with FCC Rules and Regulations as Part 15 devices. As such, they have limited transmitter power and therefore limited range.

A receiver cannot respond to more than one transmitted signal at a time and may be blocked by radio signals that occur on or near their operating frequencies, regardless of code settings.

Changes or modifications to the device may void FCC compliance.

Infrequently used radio links should be tested regularly to protect against undetected interference or fault.

A general knowledge of radio and its vagaries should be gained prior to acting as a wholesale distributor or dealer, and these facts should be communicated to the ultimate users.

211694 A