Black & Decker RB-3675, RB-3612 manual BATTERY RUNTIME INDICATOR Figure a Optional Feature only

Page 1

RB-3675 / RB-3612 36 volt lead acid BATTERY

The battery is a 36-volt sealed lead acid system. There is no liquid contained within the battery and the mower/battery can therefore be stored in any position without fear of leakage.

It is recommended that the battery be recharged after use to prolong the battery life. Frequent charging will not harm your battery, and will ensure that the battery is fully charged and ready for its next use. Storing battery not fully charged will shorten battery life.

• For optimal performance the battery should be kept on constant charge when not in use.

• The battery should be charged in its proper orientation.

• The battery prefers to be charged in a cool, dry place.

• The battery does not need to be fully discharged before recharging.

• 2 to 3 initial charging cycles may be required after purchase to achieve maximum run time capacity.

• A fully charged battery can be safely stored down to -40°F (-40°C).

• The battery is maintenance free.

• The battery is intended for use in the CM1936, CM1936Z and SPCM1936 mowers only, and the CTL36 garden tiller, and should not be used for any other purpose.

BATTERY RUNTIME INDICATOR - FIGURE A

A

 

(OPTIONAL FEATURE ONLY)

 

Your battery pack is equipped with an integral Battery Runtime

1

Indicator. When you push the “i” button A-1, the indicator will give the

 

battery runtime level.

 

At full charge, if you push the “i” button, all three LED’s will light up

 

 

indicating maximum runtime.

 

 

If you want to check the runtime during your cutting:

 

 

1. Release bail handle to turn mower off, wait until the blade stops and

 

 

remove safety key.

 

 

2. Push the “i” button to get an indication of runtime.

 

 

All three LED’s lit indicate maximum runtime available.

 

 

Two LED’s lit indicate approximately one-third to two-thirds of runtime

 

 

available.

 

 

One LED lit indicates less than one-third runtime available. You may

 

 

need to charge your battery soon. Refer to Charging Procedure.

 

A1

Inserting / removing BATTERY - Figure A1

 

NOTE: Removal of the battery pack from the Tiller is identical to the description below for the Mower.

The battery can be removed from the mower for storage/charging or left in the mower for charging.

 

Prior to removing battery, place mower on level ground.

 

 

Release bail handle to turn mower off, wait for blade to stop, and remove safety key. Prior to the

 

installation of the battery pack, ensure that the mower is clear of debris and the charger plug is

 

disconnected from the battery pack.

 

 

Insert the battery into the mower battery cavity and lift the lever A1-1to lock it in place.

 

To remove the battery, lift the lever A1-1, and then rotate back away from battery pack to unlatch

 

clasp A1-2. Lift battery pack out.

 

 

charger safety rules

NOTE: Applies to Tiller as well as Mower.

1. Plug charger directly into an electrical outlet. DO NOT ABUSE THE CORD. Never carry charger by cord. Do not disconnect the charger from the outlet, mower or battery by pulling it by the cord.

2. WARNING: To reduce the risk of fire, electrical shock, or personal injury do not attempt to use this charger with any other product. Likewise, do not attempt to charge the battery with any other charger.

3. Do not service mower with charger, safety key or battery pack installed.

4. Do not operate a damaged charger. Replace damaged cords or charger immediately at an authorized Black & Decker service center.

5. Always charge the mower in a dry area protected from the weather. Do not expose the mower, battery or charger to rain. Do not charge in wet locations. Do not charge battery when temperature is above 104°F (40°C) or below 41°F (5°C). Remove battery and charge indoors if above or below these temperatures. Charge the battery in a well ventilated location.

6. Keep the mower, battery and charger away from water, heat sources, (such as radiators, heaters, stoves, etc.) flames, or chemicals. Be careful not to damage the charger cord, by keeping cord away from sharp edges.

7. Prior to reinstalling the battery into the mower, disconnect charger plug from battery, or damage may occur.

WARNING: FIRE HAZARD

ALWAYS DISCONNECT THE CHARGER FROM THE POWER SUPPLY (WALL OUTLET) BEFORE REMOVING THE CHARGER CONNECTOR. UNDER CERTAIN CONDITIONS, WITH THE CHARGER PLUGGED IN TO THE POWER SUPPLY, THE EXPOSED CONNECTOR CAN BE SHORTED BY FOREIGN MATERIAL AND MAY CAUSE A FIRE.

FOREIGN MATERIALS OF A CONDUCTIVE NATURE, SUCH AS, BUT NOT LIMITED TO, STEEL WOOL, ALUMINUM FOIL, OR ANY BUILD-UP OF METALLIC PARTICLES, SHOULD BE KEPT FROM THE CONNECTOR. ALWAYS UNPLUG CHARGER BEFORE ATTEMPTING TO CLEAN.

Page 1 Page 2
Image 1
Page 1 Page 2
Contents Inserting / removing Battery Figure A1 BATTERY RUNTIME INDICATOR Figure a Optional Feature onlyCharger safety rules BATTERY SERVICE Charging PROCEDURE- Figure B, C, DRbrc Seal Battery Recycling Remove safety key B-1INSERTION/RETRAIT DE LA Batterie Figure A1 Fonction Optionnelle SeulementRègles DE Sécurité Pour LE Chargeur Procédure DE Charge Illustrations B, C, DLE Sceau Srprcmc Recyclage DES Piles Rechargeables Entretien DE LA PileCaracterística Opcional Únicamente Inserción / Retiro DE LA Batería Figura A1Procedimiento DE Carga Figura B, C, D Normas DE Seguridad DEL CargadorMantenimiento DE LA Batería EL Sello Rbrc Reciclado DE Baterías

RB-3612, RB-3675 specifications

Black & Decker, a well-known name in the world of power tools and home improvement equipment, offers a range of high-quality products that cater to both professional and DIY enthusiasts. Among its notable offerings are the RB-3612 and RB-3675 models, designed to enhance efficiency and performance in various tasks.

The Black & Decker RB-3612 is a versatile and efficient power tool that stands out due to its lightweight design and ergonomic grip, making it easy to handle during extended use. This model features a robust 36V lithium-ion battery, providing a longer run time and quick recharge capabilities, ensuring that users can complete their tasks with minimal downtime. The RB-3612 boasts a high-performance motor that delivers consistent power, ideal for tackling tough materials or intricate details.

One of the standout technologies in the RB-3612 is its automatic torque adjustment feature. This technology allows the tool to adapt its power output based on the material being worked on, ensuring optimal performance without stalling or damaging the workpiece. Additionally, the RB-3612 is equipped with a built-in LED light that illuminates the workspace, enhancing visibility in dimly lit areas and allowing for precision work.

Moving on to the Black & Decker RB-3675, this model is designed for users seeking added functionality and versatility. Like the RB-3612, it features a powerful motor and a 36V lithium-ion battery. However, the RB-3675 includes advanced features such as a variable speed control function, enabling users to adjust the speed settings according to their specific task requirements. This makes it suitable for a wider range of applications, from delicate tasks requiring finesse to heavy-duty jobs demanding high power.

In terms of design, the RB-3675 is engineered with a composite frame that enhances durability while remaining lightweight, which is essential for job site flexibility. It also includes a safety grip, promoting better control and reducing the risk of accidents.

Both models incorporate Black & Decker’s intelligent battery management system, which monitors battery health and enhances overall longevity. With their blend of innovative technology and user-centric features, the Black & Decker RB-3612 and RB-3675 stand out as reliable choices for anyone looking to enhance their toolkit with strong, efficient, and user-friendly tools.
Top Page Image Contents