Changing the Blade Drive Assembly

If your clipper blades no longer cut properly (be sure to try more than one blade, since the blade currently being used may be dull), it could be that your blade drive assembly needs replacement.

To change the blade drive assembly:

1.Remove blade set (Diagram G).

2.Remove drive cap (Diagram H).

DIAGRAM G

DIAGRAM H

3.Remove blade drive mounting screws (Diagram I).

4.NOTE: Before removing blade drive assembly, note the way it is positioned (this will help you in reassembly). Remove blade drive assembly (Diagram J).

8.Replace drive cap (Diagram H).

9.Replace blade (Diagram M).

DIAGRAM H

DIAGRAM M

MODEL BGC

Clipper

ANDIS AUTHORIZED

REPAIR

SERVICE STATIONS

BLADE

DRIVE

MOUNTING

SCREWS

DIAGRAM I

DIAGRAM J

5. Drive bearing should be at its lowest position, if

not, move it with your finger to lowest position

FACTORY REPAIR SERVICE

When the blades of your Andis Clipper become dull after repeated use, it is advised to send your blades to an Andis Authorized Service Station mentioned above for resharpening. If you wish your clipper to be serviced as well, they should be carefully packed and mailed either Parcel Post Insured, or U.P.S.

Please refer to the service stations listing

on web site for most up-to-date

Listings !

Thanks

Andis® Model BG

Detachable Blades

are compatible with Oster®

(Diagrams K & L).

	CORRECT	INCORRECT
		POSITION
	POSITION
		OF DRIVE
	OF
		BEARING
	DRIVE

	BEARING

DIAGRAM K

DIAGRAM L

6.Put on new drive assembly, align screw holes and press down (Diagram J).

7.Reassemble blade drive by mounting screws (Diagram I).

LIMITED WARRANTY

This Andis product is warranted against defective material or workmanship for one year from the date of purchase. All implied warranties arising and by virtue of State law shall also be limited to one year. Any Andis product determined to be defective in material or workmanship during the warranty period will be repaired or replaced without cost to consumer for parts and labor. The defective product must be returned with proof of purchase and $6.50 to cover cost of handling, to any Authorized Andis Repair Station or to: Andis, 1800 Renaissance Blvd., Sturtevant, WI 53177 U.S.A. or IN CANADA to: A & AG AGENCIES (CANADA), INC. 10050 Côte de Liesse, Lachine, Québec, H8T 1A3 CANADA. Enclose or attach a letter describing the nature of the problem. Due to foreign matter sometimes found in hair, clipper blades or resharpening of blades are not sub- ject to the one year warranty. The blade set has a 10 Day Limited Warranty. If the blade set fails to cut, it will be resharpened free of charge if returned within 10 days of purchase. Send your blade set postage prepaid with the original purchase receipt to: ANDIS COMPANY, ATTENTION: Service Department, 1800 Renaissance Blvd., Sturtevant, WI 53177 U.S.A. (U.S. & Canada only). Andis will not be liable under this warranty for any defect, failure or malfunction of any of its products cause by normal wear, abuse, misuse, unauthorized adjustments or disassembling. Andis will not be liable for any consequential damages resulting from any defect in material or workmanship of any of its products. Some States do not allow limitations on how long an implied warranty lasts or exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you. The Warranty gives you specific legal rights, and you may also have other rights which may vary from State to State.

Date

Purchased______________________________________

Model____________________________

KEEP THIS FOR YOUR RECORDS

Form # 22311 Rev. A

Printed in U.S.A.

Models 76, 10 & 111

Congratulations –

You just went First Class

when you bought this Andis Clipper.

Careful workmanship and quality design have been the hallmarks of Andis products since 1922.