Before using read the important safety instruction section in front of the manual.
Charging
Your new Smooth&Silky® Titanium should be charged for 24 hours before it can be used for the first time. It can be charged in the cleaning base or by plugging the cord into the shaver directly.
Preparing the System
Adding the cleaning solution:
1.Press the latch buttons on the sides
of the cleaning base and lift off the top
| section. You will | |
| 1 |
| need to keep the |
| buttons pressed in | |
| as you lift. | |
| 2. The cleaning solu- | |
| tion tank is in the | |
| bottom section. | |
| Remove the filter | |
| from the tank and | 2 |
| set aside. | |
| 3. Pour the bottle of | |
| cleaning solution | |
| into the base of the | |
| unit through the | |
| |
| opening where the | |
| filter was removed. | |
| 3 |
| Fill the tank to the |
| |
| bottom of the fill | |
| tab. | |
| 4. Return the filter | |
| back to its original | |
| position. | |
NOTE: It is important to make sure the filter is in place to keep the unit operating properly. The filter collects hair clippings and debris that could permanently clog the system and render it inoperable. Make sure to replace the filter whenever you replace the cleaning solution.
5.Return the top section of the cleaning base by lining up the three tall posts with the three holes in the tank. Push down the top until the two latches click into place.
6.You can dispose of the cleaning solution bottle and cap with your normal trash, or recycle where local ordinances apply.
Operating the Charging/Cleaning System
Plug the power cord into the cleaning base and then into an electrical outlet.
Remove the shaver’s clear plastic head guard and place the shaver into the unit, head side down. Push the shaver down and slide its “tail” toward the “neck” of the base until it clicks into place.
Charging
Your shaver automatically begins to recharge as soon as it clicks into place in the cleaning base. While it is charging, the green indi- cator light will flash; when it is fully charged the green light will stop blink- ing and glow steadily.
Cleaning
To activate cleaning mode, simply press the CLEAN button on the cleaning base. The yellow indicator light flashes through the entire cleaning cycle, which lasts approxi- mately 25 minutes. When the cleaning cycle has been completed, the yellow light will stop blinking and glow steadily. The unit then returns to charging mode.
!Wait until the cleaning cycle has finished before removing the shaver from the base. If the shaver is removed during the clean- ing cycle it will be covered with the special cleaning/lubricating solution and will be unusable.
Solution levels
The cleaning solution will slowly evaporate with use. When the solution levels get low, the red replacement indicator light will begin to flash. This means you have enough cleaning solution left for approxi- mately 5 more cleanings. If the red light stops blinking and glows steadily, the unit will not operate until the solution and filter have been replaced.
Replacing the Filter and Solution
Remington® cleaning solution and filters were specially designed for the WDF- 7000CS. The cleaning solution contains a high percentage of alcohol and a special oil that lubricates your shaver each time it is cleaned. The filter is specially designed to collect hair debris to keep solution clean.
To refill the cleaning solution and replace the filter, follow the steps for "Preparing the System" above. But before replacing the top of the unit, rinse out the tank with fresh water and allow it to air dry to remove any sediment.
Wipe off the base periodically with a damp cloth and remove any hair debris that has collected where the shaver sits.
!To avoid damage to the cleaning system, use only Remington® special cleaning solution. The Remington® replacement solution and filter, model #CC-100, is sold at many major retailers and online at www.remington-products.com. It can also be ordered by phone at 800-736-4648 in the U.S. or 800-268-0425 in Canada.
To Charge Your Shaver
(out of cleaning base)
The WDF-7000CS can also be recharged by plugging the cord into the shaver directly.
■Make sure your shaver is turned off.
■Use only the charging adapter supplied with the shaver.
■Connect the cord to the shaver, then plug the charging adapter into the electrical outlet. The shaver’s charging indicator will light.
■Your shaver cannot be overcharged, so you can leave it plugged in and charging between shaves.
■To preserve the life of the batteries, let them fully run out every six months, then recharge them for a full 24 hours.
NOTE: If your shaver battery is completely discharged or the shaver has not been used for a long time, charge the shaver for approximately one to two hours before shaving. After done charge for 16 hours for full charge.
