Charging the BHT-2000
Before using the for the first time, it must charge for 14-16 hours.
1.Make sure the groomer is turned off.
2.Connect the cord to the unit, then plug the charging adapter into the electrical outlet. A charging indicator will light up.
3.Your groomer cannot be over charged so you can leave it plugged in and charged between uses, but if the unit is not going to be used for an extended period of time (2-3 months) unplug it and fully recharged when you want to use it again.
4.Only use the charging adapter supplied with the unit.
5.Charging should be done at temperature between 4ºC and 35ºC, or it could decrease the battery’s life.
6.To preserve the life of the batteries, let them run out every 6 months, than recharge them for 24 hours.
7.This product is intended for cordless use only.
Before using your groomer: The High Precision Body Hair Trimmer Shaver is washable so it can be used in the shower or rinsed under water during cleaning. Therefore, to maintain the performance of the cutters, oil before each use and after rinsing. Turn the trimmer on to distribute the oil evenly. Prior to using, wipe off any excess oil. Be sure that the groomer is truned off when applying the oil.
Take a moment
Be patient when first using your BHT-2000. As with any new product, it may take a little while to familiarize yourself with it, especially if you are using a trimmer for all the first time or are using a different brand.
Take the time to acquaint yourself with your new trimmer, as we are confident you will receive years of enjoyable use and complete satisfaction.
Trimming
■Use the thumb wheel to set the trimmer comb to the desired length setting. It’s a good idea to begin trimming at one of the longest settings (4 or 5) to avoid accidentally trimming hair too short. As you become familiar with the settings, you can then select your desired length setting.
■Turn the unit on.
■Place the flat top of the trimmer comb against the skin.
■If hair builds up in the trimmer comb during the trimming process, switch the unit off, pull off the adjustable trimmer comb and brush/rinse it off.
■For an even closer look and precise shaping, remove the adjustable trimmer comb and trim the hairs along the outer edge.
■When you are finished, turn the trimmer off, clean it, and return it to its storage pouch.
Adjusting the trim length
The trimmer comb can be adjusted to give you 5 different trim lengths simply by by turning the thrmb wheel to the desired setting. Turn the thumb wheel clockwise for a shorter length, counter-clockwise for longer length. The wheel will click into place as it reaches each setting, and the setting number will appear on the length position indicator. Here’s what the length settings mean:
Setting | Length |
1 | 3mm |
2 | 5mm |
3 | 7mm |
4 | 8mm |
5 | 12mm |
!Trimmer comb must be attached to the trimmer in order to use the hair length selector.
Edging and shaping
■ Remove the trimmer comb attachment. ■ Hold the trimmer at a right angle to
your skin and press down gently. ■ Edge and shape the area as desired.
Using the shaver attachment
■Hold the shaving head to your skin.
■Stretch your skin with your free hand so hairs stand upright.
■Only apply light pressure on the shaving head while shaving.
■Shave against hair growth.
!The Microscreen shaving technology with circular foil holes is developed to give a controlled close cut.
Removing the trimmer comb and cutting assembly
■ Be sure trimmer is off. The trimmer comb may be on any setting.
■ Hold the trimmer in one hand with your thumb firmly on the thumb wheel to keep it from turning.
■ With your other hand, gently pull the trimmer comb attachment off the trimmer.
■Remove the cutting assembly by firmly pushing up on the blade with your thumb. The cutting assembly rests on a gentle spring. Use your other hand to cover the cutting assembly to prevent accidents.
Removing the shaver attachment
■Ensure the trimmer is off.
■Hold the trimmer in one hand with your thumb firmly on the thumb wheel to keep it from turning.
■With your other hand, gently pull the shaver attachment off the trimmer.
Removing the shaver cover
■Ensure the trimmer is off.
■Gently push the buttons either side of the shaving foil. With the other hand lift the shaver cover. Clean then replace.
Replacing the cutter assembly
■Ensure the trimmer is off.
■Hold the trimmer in one hand. With your
other hand, insert the lower part of the cut- ter assembly into the trimmer, push down the cutter until firmly attached.
Replacing the trimmer comb and shaver attachment
■Hold the trimmer in one hand with your thumb firmly on the thumb wheel to keep it from turning. Ensure that the length position indicator is at 1.
■Slide the comb/shaver down the grooves until it clicks into place.
!The trimmer comb and shaver attachment can only be attached in one way. If it does not go on correctly, turn it around and try again.
