HOW to Operate Your Cleaner | Panasonic MC-CG467 manual

C - HOW TO OPERATE YOUR CLEANER

C-1 Pull out the mains lead and put the plug into the socket outlet.

C-2 Gently press at the centre of the switch pedal to turn ON the vacuum cleaner.

Press the pedal again to turn it OFF.

C-3 Power control

To increase or decrease the power, turn the variable power control button.

C-4 Switching 3 positions.

Flooring (PARQUET): Set position A

Carpet (short): Set position B

Carpet (long or hard to push): Set position C

C-5The curved wand of the hose is attached with a manual suction regulator, which allows you to brieﬂ y reduce the suction level.

C-6 After you ﬁnish vacuuming, remove the plug from the wall socket and press the cord rewind pedal. When rewinding the power cord, press the cord rewind pedal by holding the plug so that it does not become damaged.

C-7 Storage position

Slide the wand holder attached to turbine nozzle pipe straight into the wand supporter on the under side of the main body.

C-8 Park position

For short breaks during vacuuming, slide the wand holder attached to the turbine nozzle pipe into the wand supporter on the rear side of main body.

NOTE: When you use park position, we suggest the appliance is switched off.

D - MAINTENANCE AND SERVICING

CAUTIONS

•The plug must be removed from the socket-outlet before cleaning or maintaining the appliance.

•To avoid injury, keep your ﬁngers and hands away from the beater bar.

•DO NOT use hot air or hot surface to dry ﬁlters. Keep at room temperature for approximately 24 hours.

•IMPORTANT: Before re-installing the washable ﬁlters, make sure they are completely dry to avoid damaging the cleaner.

Indicator for replacing the dust bag

Turn the power control to the highest setting and lift the nozzle off the ﬂ oor. If the dust indicator turns red, the dust bag is full and requires replace the dust bag.

NOTE: If the dust bag is not properly installed, the cover will not close. Be sure to check that the bag is properly installed before operating, otherwise dust will leak out. The dust bag can easily lay on the dust cover packing or clip between bag collar and body, so be sure to properly extend it into the vacuum cleaner body.

Replacing the dust bag

D-1 Lift dust cover catch and raise dust cover until it clicks properly.

D-2 Remove bag collar from bag holder and pull out dust bag.

D-3 Set a new dust bag.

D-4 Close dust cover properly until you hear it click.

Turbine nozzle

D-5After removing the brush cover with a coin, remove the beater bar from the belt.

Then cut across threads, strings, hairs, etc. from the beater bar with a pair of scissors. (Removal as per reverse procedure)

NOTE: Take care not to cut the brush.

Do not wash in water.

Vacuum cleaner body

D-6Wipe with a soft cloth soaked with water.

Maintaining the Pre-motor Filter

Follow the procedure written below when the suction power is not restored after replacing a new bag.

D-7 Open the dust cover.

D-8 Remove the pre-motor ﬁlter.

D-9 Wash gently with water and then allow to dry in a shaded location.

D-10 Replace to its original location.

NOTE: Make sure you remember to replace the ﬁ lter. If the

ﬁlter is not installed, it will cause motor failure.

•Do not wash the ﬁ lter in a washing machine or dry it with a dryer or other source of hot air.

Filter care

D-11 Exhaust ﬁlter

Exhaust ﬁ lter is installed in the rear side of the vacuum cleaner. This ﬁ lter retains any small dust particles which may be present in the expelled air. It is advisable to change the ﬁ lter once or twice a year, depending on use. To change the ﬁ lter, hold the exhaust cover (as illustrated) and pull it out. After changed the ﬁ lter, set the exhaust cover to its position (as illustrated).

NOTE:

IMPORTANT: Never use the cleaner without the correct

ﬁlters properly installed. Failure to do so may result in damage to the motor.

What to do if your cleaner does not work

Check that the appliance is correctly plugged in and that the electrical socket is working. In case that the thermal cut-out device has operated, wait until it resets after approximately

60 minutes. If after having checked the mentioned points, the cleaner does not work, take it to an Authorized Service Centre to be repaired.

What to do when the suction performance reduces

•Stop the cleaner and unplug from the socket.

•Check whether the wands, hose and accessories are blocked or not. If they are blocked, remove the obstruction.

•Check that the dust bag is full. If it is full, replace it to a new one.

•Check that Pre-motor Filter or Exhaust Filter is blocked with dust. If they are blocked, clean them out or replace.

	SPECIFICATIONS	MC-CG467
	POWER SOURCE	AC120V ~ 60Hz
	CURRENT	11Amps
	AUTOMATIC CORD REWIND	YES
	DUST BAG	PAPER
	DUST CAPACITY	3.0L
	CORD LENGTH	5.0m (16Ft.)
	EXTENSION WANDS	METAL TELESCOPIC
	NOZZLE	3 in 1 TURBINE NOZZLE
	WEIGHT (WITH	4.5 kg (9.9lbs.)
	ACCESSORIES)	4.5 kg (9.9lbs.)
	ACCESSORIES)
	DIMENSIONS	280mm×425mm×260mm (11in×16.7in×10.2in)
	(W×L×H)	280mm×425mm×260mm (11in×16.7in×10.2in)
	(W×L×H)
	ACCESSORIES NOZZLE	CREVICE NOZZLE & DUSTING BRUSH

REMINDER FOR CUSTOMER

The model and serial number of this product may be found on the nameplate located at the underside of your cleaner. You should note the model and serial number in the spaces provided and retain this book as a permanent record of your purchase.

Model Number.

Serial No.

Date Purchased.

Where Purchased.

MC-CG467 specifications

The Panasonic MC-CG467 is a powerful and versatile canister vacuum cleaner designed for efficient cleaning around the home. Combines sleek design with advanced technology to ensure a thorough clean on various surfaces. Equipped with features that prioritize convenience and performance, the MC-CG467 is popular among homeowners looking for effective cleaning solutions.

One of the standout features of the Panasonic MC-CG467 is its powerful 12-amp motor. This robust motor provides strong suction power, ensuring the vacuum can tackle even the most stubborn dirt and debris. The motor's efficiency translates into consistent performance, making it suitable for cleaning carpets, hardwood floors, and various fabric surfaces.

The vacuum comes with an adjustable telescoping wand, allowing users to customize the cleaning reach according to their needs. This feature makes it easy to clean hard-to-reach areas such as under furniture or high ceilings. The ergonomic design of the handle enhances user comfort, reducing strain during extended cleaning sessions.

The MC-CG467 is equipped with a large capacity dust bag, which minimizes the frequency of bag replacements. The bag is designed to capture and contain fine dust and allergens, promoting a cleaner and healthier indoor environment. The vacuum also features a bag change indicator, which alerts users when it’s time to replace the dust bag.

Another notable technology integrated into the Panasonic MC-CG467 is the automatic carpet height adjustment. This feature allows the vacuum cleaner to adapt its height based on the type of flooring, ensuring optimal suction and efficiency whether on carpets or hard surfaces.

For added versatility, the MC-CG467 comes with a range of specialized attachments, including a dusting brush, crevice tool, and upholstery nozzle. These tools make it easy to clean various surfaces effectively, from delicate drapes to tight spaces between furniture.

In terms of noise levels, the MC-CG467 operates relatively quietly, making it suitable for use in households where a quieter cleaning operation is preferred. Overall, the Panasonic MC-CG467 is a reliable and efficient vacuum cleaner that effectively meets the diverse cleaning needs of modern households. With its combination of power, adaptability, and user-friendly design, it continues to be a favored choice for those seeking a high-quality cleaning machine.