Trimmer Guard Attachment (continued)
Maintenance
To Define Beard Line
1.Hold Trimmer vertically with front of Trimmer fac- ing you.
2.Start with trimmed edge of beard and with down- ward motions trim area directly under the beard line.
To Thin and Taper Beard
1.Use a small comb to hold hairs in place while trim- ming.
2.Hold Trimmer with front of Trimmer facing away from you.
3.Trim hair ends using an upward motion.
4.Turn Trimmer OFF.
To Trim Moustache with Trimmer Guard Attachment
• Be certain Trimmer Guard |
Attachment is on to pre- |
•Hold Trimmer vertically with front of Trimmer fac- ing you.
•Trim hairs using a down- ward motion following the direction of your hair growth or you may trim against your hair growth— whichever is preferred.
NOTE: Since all hairs do not grow in the same direction, you may want to try different trimming positions (i.e. upwards, downwards or across). Practice is best for opti- mum results.
To Trim Moustache without Trimmer Guard Attachment
1. | Remove Trimmer Guard |
| Attachment. |
2. | Place a finger on upper lip |
| to lift hair up, away from |
| skin. |
NOTE: Use a slow and gentle pressure. Too much pressure may trim more hair than desired.
5. Turn Trimmer OFF.
To Trim Sideburns
1.Comb sideburns following the direction of your hair growth.
2.Be certain Trimmer Guard Attachment is ON.
3.Hold Trimmer vertically with front of Trimmer fac- ing you.
4.Trim sideburns using a downward motion.
5.Turn Trimmer OFF.
To Achieve The
“Stubble” Look
•The Trimmer Guard Attachment is unique because it has a small slot between the two rows of teeth enabling you to trim hairs to only .06 in./1.5mm in length.
1.Be certain Trimmer Guard Attachment is ON and Zoom Ring is on the low- est setting (#1).
2.Hold Trimmer horizontally with front of Trimmer fac- ing downwards or upwards.
3.Trim hairs using a down- ward or upward motion, whichever is more com- fortable, following the direction of your hair growth (Fig. 11).
4.Turn Trimmer OFF.
IMPORTANT
•Always switch Trimmer OFF before cleaning.
•Never clean, remove or replace Trimmer Guard Attachment with motor on.
•Do NOT apply pressure to cutters.
•Do NOT touch cutters with hard objects as this may damage them.
•If Trimmer is not used reg- ularly, remove batteries to prevent possible damage due to chemical leakage.
•DO NOT use while bathing, showering or immerse the unit in water or other liquids as damage to Trimmer may occur.
•NEVER use harsh or cor- rosive cleaners such as benzene or bleach.
During Use
•If cut hairs have accumu- lated in the comb area, pull Trimmer Guard Attachment off Trimmer (Fig. 13) and remove hairs by shaking and/or blowing (Fig. 14).
Once A Week
1.Be certain Trimmer is in OFF position.
2.Remove Trimmer Guard Attachment.
3.Hold Trimmer as shown and gently push cutter tab (located beneath the cut- ters) backwards (Fig. 15).
4.Lightly brush out cutters, hair chamber and Trimmer Guard Attach- ment (Fig. 16 &17) with cleaning brush provided.
To Replace Cutters
If your cutters become dam- aged or worn, do not contin- ue using the Trimmer.
Replace cutters immediately.
1.Remove the old cutters by pushing cutting unit back- wards (see Fig. 15) and then pull it upwards off Trimmer.
2.Place the two notches of the new cutting unit into the guide slots (Fig. 18).
15 |
3.Push the cutting unit back until it “clicks” into place (Fig. 19).
17 |
18 |
vent trimming off too |
many hairs. |
1.Comb hairs outward so they are at their maximum height and in the same direction.
2.Set Zoom Ring to desired setting.
3. | Trim hairs using an |
| upward motion. |
4. | After achieving desired |
| length, use a downward |
| motion to blend mous- |
| tache hairs (Fig. 10). |
10
11
13 |
14 |
16 |
1 |
2 |
19 |
2 |
CLICK |
1 |
1 |