Philips T-4000 To Insert Batteries, To Remove Batteries, To Trim Beard, To Replace

Batteries

One Stroke Comb Adjustment

Trimmer Guard Attachment

•Your new Trimmer requires 2 “AA” 1.5 V alkaline or carbon zinc batteries.

To Insert Batteries

1.Be certain Trimmer is in the OFF position.

2.Hold Trimmer horizontally and press the release tabs located at base of Trimmer. Gently slide bat- tery compartment out of Trimmer housing until it stops (Fig. 1)

NOTE: Battery compart- ment is not removable.

3.Insert the batteries as shown making sure the (+) and (-) markings on the batteries match those on inside compartment of Trimmer (Fig. 2).

4.Slide the battery compartment back into Trimmer housing (Fig. 3).

NOTE: Trimmer will not operate if batteries are inserted incorrectly. If you do not intend to use the appliance for a long time, remove the batteries. Leaking batteries can cause damage to the product.

To Remove Batteries

1.Follow steps 1-2 above. Push the batteries out of the holder as shown (Fig. 4).

•	Trimmer Guard
	Attachment must be in
	place on the Trimmer in
	order to use the One
	Stroke Comb Adjustment
	feature.
•	One Stroke Comb
	Adjustment with Trimmer
	Guard Attachment
	ensures precise trimming
	and has 4 adjustable
	positions (see chart
	below).
• Slide One Stroke Comb
	Adjuster to desired set-

into position.

•Start at a longer setting (#4) to prevent accidental- ly trimming hairs too short (Fig. 5).

•Trim against the direction of hair growth (Fig. 6)

•As you become familiar with the settings, slide Adjuster to desired trim- ming length.

To Remove

•Remove Trimmer Guard Attachment if you are:

•Defining hair lines

•Trimming nape of neck

•Removing single, unwant- ed hairs

1.	Be certain Trimmer is in
	the OFF position.
2.	Hold Trimmer base with
	one hand, grasp sides of
	Trimmer Guard Attach-
	ment and gently slide

2.Hold Trimmer in one hand and replace Attachment back onto Trimmer until it “clicks” into position.

NOTE: The Trimmer Guard Attachment can be placed on Trimmer only one way. If it does not fit properly, reverse it.

To Trim Beard

1.	Comb hairs outward so
	that they are at their maxi-
	mum height and in the
	same direction.
2.	With Trimmer Guard

Trimmer without Trimmer Guard Attachment, use a slow, very light “skim- ming” technique to prevent trimming off more than the desired amount of hair.

To Trim Outer Edge of Beard

& Add Definition

1.	Remove Trimmer Guard
	Attachment.
2.	Hold Trimmer diagonally
	with front of Trimmer fac-
	ing away from you (Fig. 9).
3.	Turn Trimmer ON.

2

ting. Adjuster will “click”

#1	Stubble Length or Closely Cropped	.06 in./1.5 mm
#2	Short	.12 in./3 mm
#3	Medium	.2 in./5 mm
#4	Long	.28 in./7 mm

Attachment off Trimmer

(Fig. 7).

NOTE: Attachment can be removed while it is on any setting.

To Replace

1.Be certain Trimmer is in the OFF position.

	Attachment in place, set
	One Stroke Comb
	Adjuster to desired set-
	ting.
3.	Slide On/Off switch to the
	ON position and begin
	trimming (Fig. 8).
4.	Turn Trimmer OFF.
	IMPORTANT: If using

4.	Start at chin and work
	back toward ear.
5.	Follow line of jawbone to
	cut away longer hairs on
	outer edge of beard.
6.	Turn Trimmer OFF.
	NOTE: Practice is best for
	optimum results.

1 3

CLICK

5	4
	3
	2
	1
	4
2
	1

6
4
		3	4
	2
1

7	8
	4

9