Braun service manual Maintenance and Lubrication Schedule, 750

Page 15

Maintenance and Lubrication Schedule

Proper maintenance is necessary to ensure safe, troublefree operation. Inspecting the lift for any wear, damage or other abnormal conditions should be a part of all transit agencies’s daily service program. Simple inspections can detect potential problems.

The maintenance and lubrication procedures specified in this schedule must be performed by a Braun autho- rized service representative at the scheduled intervals according to the number of cycles.

Braun dual parallel arm lifts are equipped with hard- ened pins and self-lubricating bushings to decrease wear, provide smooth operation and extend the service life of the lift.

following the scheduled “4500 Cycles” mainte- nance. These intervals are a general guideline for scheduling mainte- nance procedures and will vary according to lift use and conditions. Lifts exposed to severe conditions (weather, envi- ronment, contamination, heavy usage, etc.) may require inspection and maintenance procedures to be performed more often than specified.

WARNING

Maintenance and lubrication procedures must be performed as specified by an authorized service technician. Failure to do so may result in serious bodily injury and/or property damage.

When servicing the lift at the recommended intervals, inspection and lubrication procedures specified in the previous sections should be repeated. Clean the components and the surrounding area before apply- ing lubricants. LPS2 General Purpose Penetrating Oil is recommended where Light Oil is called out. Use of improper lubricants can attract dirt or other contaminants which could result in wear or damage to the components. Platform components exposed to contaminants when lowered to the ground may require extra attention.

Lift components requiring grease are lubricated during assembly procedures. When these components are replaced, grease must be applied during installation procedures. Specified lubricants are available from The Braun Corporation (part numbers provided above).

All listed inspection, lubrication and maintenance procedures should be repeated at “750 cycle” intervals

Maintenance Indicator: The Lift Ready green LED mounted on top of the pump cover will begin to blink after every 750 cycles. The blinking LED will not affect the functions of the lift, but is a reminder to complete necessary maintenance and lubrication.

Once the lift has been serviced, fully stow the lift. Once stowed, press the UP button on the hand pendant and the Floor Level Set button on the back side of the pump cover until the Lift Ready green LED stops blinking.

Discontinue lift use immediately if maintenance and lubrication procedures are not properly performed, or if there is any sign of wear, damage or improper opera- tion. Contact your sales representative or call The Braun Corporation at 1-800-THE LIFT®. One of our national Product Support representatives will direct you to an authorized service technician who will inspect your lift.

 

Outer barrier hinge pivot points (2)

Apply Light Oil - See Lubrication Diagram

 

Outer barrier latch (pivot/slide points)

Apply Light Oil - See Lubrication Diagram

 

Outer barrier latch lever pivot points

Apply Light Oil - See Lubrication Diagram

 

Lift-Titelatches (tower pivot points - 2)

Apply Light Oil - See Lubrication Diagram

 

Lift-Titelatch gas (dampening) spring pivot

Apply Light Oil - See Lubrication Diagram

750

points (2 springs - 4 points)

 

Cycles

Inspect Lift-Titelatches and gas springs for wear

Resecure, replace defective parts or otherwise

 

or damage (bent, deformed or misaligned), posi-

correct as needed. Note: Apply Light Grease to

 

tive securement (external snap rings) and proper

Lift-Titelatch tower pivot point if replacing latch.

 

operation

 

 

Inspect outer barrier for proper operation

Correct or replace defective parts.

 

Inspect outer barrier latch for proper operation,

Correct or replace defective parts and/or relubri-

 

positive securement, and detached or missing

cate. See Lubrication Diagram

 

spring

 

 

 

 

Page 13

Image 15
Contents CA Congratulations Warranty and Registration InstructionsContents Platform Lift TerminologySwitch and Sensor Locations Certification Checklist Diagnostic Procedures Outer Barrier Fold Pressure Adjustment Platform Fold Pressure AdjustmentPlatform Angle Adjustment Millennium NL SeriesCentury NCL Series Vista NVL Series Platform Stop Blocks Platform Floor Level Adjustment Bridging Microswitch Adjustment Bridging MicroswitchAdjustment Guidelines LCD Lift Codes Troubleshooting ProceduresFlashing Numbers Non-Flashing NumbersLG Light Grease Maintenance and LubricationLO Light Oil DE Door-Ease750 Maintenance and Lubrication Schedule750 Cycles 1500 Page Lift Electrical Schematic Unfold Lift Wiring DiagramDescription Symbol Hydraulic SchematicHydraulic Fluid Hydraulics Parts ListHydraulics Diagram Part Numbers of Items Dedicated per Lift Model Pump Module Parts ListPump Mounting Bolts Pump Module DiagramFloor-to-Ground Lift Repair Parts List Part Numbers of Items Dedicated per Lift ModelPart Numbers of Items Identical on All Lift Models Floor-to-Ground Lift Exploded View ExplodedView NL916IB NL916FIB NL917IB NL917FIB NL919IB NL919FIB Page Providing Access to the World CA
Related manuals
Manual 32 pages 39.92 Kb

5 specifications

The Braun 5 series is a standout in the realm of electric shavers, showcasing a blend of performance, comfort, and innovative technology designed for the modern man. Renowned for its ergonomic design and user-friendly features, the Braun 5 has become a reliable grooming companion for those seeking an efficient and smooth shaving experience.

One of the most notable features of the Braun 5 is its FlexMotionTec technology. This advanced system allows the shaver head to move with the curves of the face, ensuring optimal contact with the skin. This flexibility significantly reduces skin irritation while providing a thorough shave, making it particularly beneficial for individuals with sensitive skin.

The shaver's Adaptive Shaving Technology is another key characteristic. It intelligently adapts to the density of the beard hair, adjusting its power and speed accordingly. This ensures a consistent, close shave, even in challenging areas, without the need for multiple passes. The precision trimmer, located on the back of the shaver head, adds versatility, allowing for neatly defined sideburns and mustaches.

Additionally, the Braun 5 comes with a waterproof design, making it suitable for both dry and wet shaving. Users can enjoy the convenience of using gels or foams for a more comfortable glide, or simply opt for a quick, dry shave when time is of the essence. The shaver is easy to clean under running water, further enhancing its user-friendly appeal.

Battery performance is another highlight of the Braun 5 series. With a powerful Li-Ion battery, the shaver provides robust performance with up to 50 minutes of cordless shaving on a single charge. A quick 5-minute charge offers enough power for one full shave, making it a practical choice for those always on the go.

In summary, the Braun 5 series electric shaver combines precision engineering with thoughtful features aimed at delivering an exceptional shaving experience. The blend of FlexMotionTec and Adaptive Shaving Technology, coupled with its ergonomic design and robust battery life, makes the Braun 5 an indispensable tool for modern grooming. For those in search of quality, comfort, and efficiency in their daily shave, the Braun 5 stands out as a top choice in the electric shaving market.