—— INSTALLATION ——
TABLE/DESK INSTALLATION
Use the
!
WARNING:
Do not plug the handset cord into the line jack or the data jack on your telephone since it could damage your handset and the telephone.
1.Turn the telephone upside down so that you can see the bottom of the telephone. See Figure 2.
Desktop stand
Line jack
4 holes for 
wall mounting
6.Turn the telephone
7.Plug one end of the coiled handset cord into the handset jack on the side of the telephone.
8.Plug the other end of the handset cord into the handset.
9.Hang up the handset.
10.Plug the free end of the line cord into a modular wall jack.
11.Lift the handset and listen for dial tone.
12.Set the Ringer volume control (labeled 
) to the setting you want.
WALL INSTALLATION
Use the following directions to mount the telephone on a standard wallphone jack with mounting studs.
NOTE: For wall installation, use an
(PEC:
1.You must reverse the handset tab (which holds the handset when you hang up). See Figure 5.
•Hold down the switchhook and slide the handset tab up and out of its slot.
•Turn the tab so that the curved end is facing up.
•Insert the tab back into its slot.
Figure 2. The Bottom of the 6200 Series Telephones
2.Remove the desk stand by sliding it to the left until it is free of the telephone base. See Figure 3.
a. Handset | b. Press to release |
retainer | and then remove |
in place | handset retainer |
Desktop |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Slide stand |
stand |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| to left and lift |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Figure 3. Sliding the Base from the Bottom of the Set
3.Plug one end of the line cord into the line jack on the bottom of the telephone.
4.Align the other end of the line cord so that it is threaded through the slot at the top of the stand. See Figure 4.
5.Reattach the stand to the telephone by sliding the stand into the appropriate tabs and to the right.
Line cord
Desktop stand
c. Reposition |
| d. Replace handset |
handset | (up | retainer |
retainer |
| |
position) |
| |
down |
|
(down
position)
Figure 5. Reversing the Handset Hook
2.Turn the telephone upside down so that you can see the bottom of the telephone.
3.Remove the mounting base by sliding the base to the left until it is free of the telephone. See Figure 3.
4.Turn the base so the larger end is down.
5.Plug one end of the
6.Slide the reversed base onto the telephone, to the right, until it snaps into place. See Figure 6.
Invert stand
Line jack |
LINE
Figure 4. Attaching the Line Cord and Threading It Through the Slot at the Top of the Desktop Stand
Holes for wall mounting
Position stand over 4 holes, push stand down, and slide to left
Figure 6. Installing the Stand for Wall Mounting
2