DCT2800 SERIES USERS GUIDE
1.8 GHz DECT Two-Line Cordless Guestroom Telephone
DCT2800 SERIES DIAGRAM
CONTACTING TELEDEX
Telephone
Main: +1.408.363.3100
Fax:
Internet
www.teledex.com
sales@teledex.com
Mailing Address
6311 San Ignacio Avenue
San Jose, CA 95119 USA
Part Number
Copyright © 2006 Teledex LLC.
ALL RIGHTS RESERVED.
INCLUDED IN YOUR PACKAGE
Cordless Handset | AC Adapter |
Base Unit | User Guide |
NiMH Battery | |
Rubber Battery Screw Cover | |
Phillips Screw | Clear Plastic Overlay |
PREPARING TO USE THE DCT2800 SERIES
1.Prepare to install the battery into the cordless handset by firmly pressing down on the top of the battery cover and sliding it off. If cover is secured with a screw, remove the screw first.
2.Locate the lightly embossed numbers “1” and “2” on the battery’s plastic connector.
3.Insert the battery connector into the handset’s connector with the embossed numbers facing up.
Note: The handset may “beep” when the battery is connected. This is not an indication that the telephone is ready to use. To obtain optimal perform- ance of the telephone, be sure to charge the battery for 15 to 20 hours.
4. Replace the battery compartment cover and retaining screw.
5.Insert the provided rubber screw cover.
6.Turn the telephone base so the back panel is facing you. Insert either end of the
7.Insert the other end of the cable into the jack on the AC adapter labeled PHONE.
8.Insert one end of the
9.Insert the other end of this line cord into a telephone jack.
10.Plug the AC adapter into an unswitched electrical outlet.
11.Once your telephone is connected, remove the plastic overlay and place the paper faceplate over the keys. Replace the plastic overlay by hooking the tabs on the overlay into the recessed slots located on both sides. The overlay is easiest to insert when the left or right side tabs are inserted first, and the middle of the overlay is slightly bowed to allow for insertion of the other tabs.
12.Place the cordless handset on the base unit.
CHARGING THE BATTERY
The rechargeable battery must be fully charged before using the phone for the first time. It is recommended that that battery pack be charged for approximately 15 to 20 hours, without interruption, before use. To charge the battery, place the handset, keypad down, in the base unit. Make sure the CHARGE LED on the base lights.
If the LED does not light:
1.Ensure that the AC adapter is plugged in.
2.Ensure that the AC adapter is not plugged into a switched electrical outlet.
3.Ensure that the handset charging contacts at the bottom of the handset are making good contact with the base unit’s charging contacts.
CLEANING THE BATTERY CONTACTS
To maintain a good charge, it is important to clean all charging contacts on the handset and base unit. Use a pencil eraser or other contact cleaner. Do not use any liquids or solvents.
BATTERY SAFETY INSTRUCTIONS
1.Use only
2.Dispose of used batteries according to local codes pertaining to NiMH batteries.
3.Do not dispose of batteries in fire, as they may explode
4.Charge the telephone's batteries only while in the telephone handset, and only by using the telephone base unit to charge. Do not attempt to remove the batteries and charge them in a separate charging unit.
5.Do not
HANDSET/BASE REGISTRATION PROCEDURE
This procedure establishes an exclusive link between a specific handset and base, thereby allowing no other access to this specific base. To accomplish this procedure, place the handset on the base in the charging position. The LINE indicator will blink while the process is occuring. This process occurs each time the handset is placed on the base in the charging cradle.
ADJUSTING THE RING VOLUME
The up and down volume keys will adjust the ringer volume of the telephone. Additionally, the DCT2800 series telephone has an optional “courtesy” ring mode, wherein the ring volume begins at the lowest setting, then automatically rings louder with each successive ring during an incoming call. To select the courtesy ring mode, follow these steps:
Press the FLASH key; then the 4 key; then the STORE key; then press the number on the keypad that corresponds to the line for which you wish to change to courtesy ring mode, i.e; press the number 1 for line 1, and the number 2 for line 2.
To return to regular ring mode: Press the FLASH key; then the 1 key; then the STORE key; then the number on the keypad that corresponds to the line for which you wish to change regular ring mode.
ADJUSTING SPEAKERPHONE VOLUME
The speakerphone has eight (8) levels. To adjust speakerphone volume, locate the volume up/down keys, located on the front surface of the phone below the keypad. With the speaker active,