CONNECTING THE OPAL
Included with the Opal are (one each): | | |
• | Base unit | • | Coiled handset cord | • | User guide |
• | Handset | • | Clear plastic overlay | • | Line cord |
Contact your supplier or Teledex for information on ordering custom designed and printed faceplates to enhance the look of your Teledex telephone.
1)Located on the left side of the Opal (as the phone is facing you) is a modular jack. Insert one end of the coiled handset cord into this jack (you should hear the coil cord click when properly inserted).
2)Insert the other end of the coiled handset cord into the modular jack on the handset.
3)Turn the telephone so the back panel is facing you. Insert either end of the line cord into the jack on the back of the telephone labeled LINE.
4)Insert the other end of the line cord into a telephone wall outlet jack.
5)Once your telephone is connected, remove the plastic overlay and place the paper faceplate over the keys. Replace the plastic overlay by hooking the tabs on the overlay into the recessed slots located on both sides. The overlay is easiest to insert when; the left or right side tabs are inserted first, and the middle of the overlay is slightly bowed to allow for insertion of the other tabs.
PLACING A CALL
1)Lift the handset.
2)Listen for dial tone. Dial the desired number, or press an AUTO DIAL key to automatically dial a number.
3)To end the call, hang up by placing the handset back in the cradle.
RECEIVING A CALL
An audible ring and flickering red message waiting light will indicate an inbound call.
1)Lift the handset. The Opal will engage the ringing line.
2)To end the call hang up the handset.
ADJUSTING THE RING VOLUME
Locate the adjustment control on the back of the telephone labeled RINGER LOW/HI. Slide the switch to the desired LOW or HI ring vol- ume.
REDIAL (models Opal 1003/1005/1010 only)
To REDIAL the last telephone number dialed:
1)Lift the handset from the cradle.
2)Press the REDIAL key.
ADJUSTING THE HANDSET VOLUME
The HANDSET VOLUME key has three levels. When the handset is first lifted, the handset volume is NORMAL.
Locate the HANDSET VOLUME key below the keypad. Press the key once and the volume level will increase one level (to MEDIUM vol- ume). Press the key once more and the volume level will increase an additional level (to HIGH volume). To return the handset volume to NORMAL, press the handset volume key again.
The handset volume will always return to NORMAL when the hand- set is replaced in the cradle.
FLASH KEY (models Opal 1003/1005/1010 only)
Pressing the FLASH key initiates a 600ms hookflash. Typical usage is to access PBX features like call waiting.
AUTO DIAL KEYS
The Opal has programmable AUTO DIAL keys. These keys can be programmed to automatically dial telephone numbers, or activate telephone system features.
Programming AUTO DIAL keys:
The telephone must be connected to a telephone line. 1) Lift the handset from the cradle.
2)Press the recessed STORE key and release it. (Please see diagram on the next page).
3)Enter the telephone number including PAUSE* as required. The sequence can be up to 15 digits.
4)Press the AUTO DIAL key where the number is to be stored.
5)Place the handset back in the cradle.
*A 3.6 second pause is entered in a dialing sequence by pressing the REDIAL key for each PAUSE required.
RMA PROCEDURES
The following procedure should be followed with all Teledex tele- phone products prior to sending the telephone to the factory for repair.
1)Please perform the tests listed below:
a.Test the telephone on a different telephone jack.
b.Test telephone with a different line cord.
c.Test with a different handset cord (coiled cord).
d.For two line products, please ensure that one of the line buttons is pressed (if both line buttons are in the UP position, the telephone will not operate).
2)If the steps listed above do not provide a remedy for the suspect telephone, please place a tag on the individual telephone describing the defect. Next, call the Teledex Repair Department at 1 (800) 875-8539for an RMA number. You must have an RMA number to return products to Teledex.
3)Kindly note: An RMA number is unique to each return shipment. Do not duplicate this number on any future shipments.
SHIPPING INSTRUCTIONS:
Please print the RMA number clearly on the outside of your shipping carton(s). Please ship to the following address:
Teledex LLC / RMA#___________
6311 San Ignacio Avenue
San Jose, CA 95119
FREIGHT CHARGES:
The Customer is responsible for shipping products for repair to Teledex. After repair, Teledex will return telephone products to the Customer freight prepaid in the same manner in which is was sent (i.e. Freight sent to Teledex UPS Blue, will be returned via 2 day ship- ping).
**Please note: When telephones are returned for repair due to misuse (i.e. liquid spills, abuse, or Customer modification - warranty label broken), the Customer will be charged the standard repair fee, regard- less of warranty status.
CONVERTING FROM DESK TO WALL MOUNT
The Opal Telephone can be changed for wall mounting applications. The conversion is easiest when the handset and line cords are not connected.
1)Located on the top of the telephone above the speaker grill is the wall/desk mount clip. Remove this clip by firmly pushing upward (towards the hookswitch).
2)Flip the clip over (top to bottom) so that the protruding edge is towards the top of the phone. This edge will hold the handset.
3)Turn the Opal over so the bottom is up facing you. Place the Opal on a nonabrasive surface to prevent scratching.
4)Locate and remove the mounting bracket, firmly push back and pull up to remove two of the four retaining tabs.
5)Rotate the mounting bracket 180 degrees clockwise so that the mounting eyelet on the bracket is facing in the same direction as the other mounting eyelet located on the bottom of the telephone.
6)Insert the top two retaining tabs of the mounting brackets into the mounting bracket slots (located near the middle of the tele- phone). Then firmly push down to insert the retaining tabs on the opposite side of the mounting bracket.
7)Connect a short modular line cord into the jack on the back of the phone (labeled LINE). Route the line cord thought the line cord channel. Connect the other end of line cord to the phone jack on the wall mounting plate.
8)Turn the telephone over, and slide the Opal down onto the
