00 mm, 270, Important Note | Radio Shack PBT55D specification

400.00 mm

7.Transfer call

a.To transfer a call from the Headset to your mobile phone

If the mobile phone is enabled with the Hands-free profile, press the button while the call is in session and it will be transferred to your mobile phone.

If the mobile phone is enabled with the Headset profile, follow the instructions of your mobile phone manual to do call transfers.

b.To transfer a call from your mobile phone to the Headset

Follow the instructions of the mobile phone manual to do call transfers

	Volume
	up
	+
Backward	Forward
	Forward

Volume

down

II.[ B ] Stereo Headset paired with Stereo Audio Adaptor Guide

1.Pairing

a. While the Headset is powered off, press and hold button for 4 seconds. The LED will flash red and green alternatively, which indicates the Headset in Pairing Mode. The Pairing Mode will last for one minute.

b. While the Stereo Audio Adaptor is powered off, press and hold button. The LED will flash red and green alternatively, which indicates the Audio Adaptor is in Pairing Mode. The Pairing Mode will last for one minute.

c.Put the Headset and the Audio Adaptor close to each other, 0.5 to 3 meters. After a few seconds, their LED’s will turn into flashing green, which indicates successful pairing. Both units are in Standby Mode and ready to transmit audio signal, or music from the audio source.

2.Listening to music

a.After successful pairing, plug the jack of the Audio Adaptor to the 3.5 mm socket of any audio source such as iPod, MP3, CD player, Notebook PC, or others.

b.Put the earpiece on.

c.Play the music on the audio source as normal; you will listen to the stereo music from the earpiece.

IV. [ D ] Stereo Headset paired with Bluetooth enabled PDA Guide

1.Pairing

a.While the Headset is powered off, press and hold button for 4 seconds. The LED will flash red and green alternatively, which indicates the Headset in Pairing Mode. The Pairing Mode will last for one minute.

b.Put the Headset and the Bluetooth enabled PDA (with A/V profile) close to each other, 0.5 to 3 meters.

c.Follow the operation instructions of your Bluetooth enabled PDA (with A/V profile) to start the pairing process. Typically, this has to be done by going to a setup or connect menu to discover the Headset. It may take some time to search it depending on the number of Bluetooth devices nearby.

d.Your PDA will display the model name “PBT55D” if it has found the Headset; and ask for a passkey. Enter a sequence of “0000”. After successful pairing, follow the instructions to establish the Bluetooth connection with the Headset.

e.If the pairing is successful, the LED will flash green, which indicates it is in Standby Mode and ready to receive audio signals from the PDA. If pairing does not occur as expected, turn the Headset and the PDA off. Wait for 10 seconds and repeat the pairing process from the beginning.

2.Listening to music

a.Put the earpiece on.

b.Play the music on the PDA as normal; you will listen to the stereo music from the earpiece.

c.The speaker volume of the earpiece can be adjusted by pressing the VOL+/ VOL- buttons.

d.While listening to music (for example, song 2), press the Headset’s FORWARD >> button will skip to next song (for example, song 3); press the BACKWARD << button will replay the current song (for example, song 2). Double press the BACKWARD button will play the last song (for example, song 1). This remote control function is supported only by the AVRCP profile of your Bluetooth application program.

e.Turn the Headset off after use.

VI. [ A & C ] Stereo Headset paired with

USB Bluetooth dongle and Bluetooth mobile phone Guide

	Bluetooth
USB Bluetooth dongle	Stereo Headset	Bluetooth mobile phone
USB Bluetooth dongle		Bluetooth mobile phone
[ C ]		[ A ]

1.Pairing

a.Follow the Pairing process [ C ] to pair the Headset and the USB Bluetooth dongle.

b.After successful pairing, turn the Headset off.

c.Follow the pairing process [ A ] to pair the Headset and the Bluetooth mobile phone.

d.After successful pairing, please follow the PC Bluetooth application program instructions to re-establish the Bluetooth connection between the Bluetooth dongle and the Headset.

e.All three devices are in Standby Mode and the LED’s should flash green.

2.Listening to music

a.Follow the Listen to music process [ C ] to enjoy the music.

3.Monitoring mobile phone calls

a.Follow the [Advance function] in [ A ] to monitor phone calls

Federal Communication Commission

Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.

IMPORTANT NOTE:

FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

FCC ID: NV6-CS8076

Bluetooth Qualified Design ID: B011669

.00 mm

d.The speaker volume of the earpiece can be adjusted by pressing and releasing the VOL + / VOL- buttons.

e.Turn the Headset off after use. The Audio Adaptor will be turned off automatically. Next time, you don’t need to pair them again. Turn them on, and then they will be paired automatically and ready to transmit music from the audio source.

III.[ C ] Stereo Headset paired with USB Bluetooth Dongle Guide

1.Pairing

b.Put the Headset, the USB Bluetooth dongle and the PC close to each other, 0.5 to 3 meters.

c.Insert the USB Bluetooth Dongle into a USB port of your Notebook PC / desktop PC to start the pairing process. Typically, this has to be done by executing a Bluetooth application program supporting the Audio Visual (A/V) Profile, to discover the Headset. It may take some time to search it depending on the number of Bluetooth devices nearby.

d.Your PC will display the model name “PBT55D” if it has found the Headset; and ask for a passkey. Enter a sequence of “0000”. After successful pairing, follow the instructions to establish the Bluetooth connection with the Headset.

e.If the pairing is successful, the LED will flash green, which indicates it is in Standby Mode and ready to receive audio signals from the dongle. If pairing does not occur as expected, turn the Headset and the PC off. Wait for 10 seconds and repeat the pairing process from the beginning.

2.Listening to music

a.Put the earpiece on.

b.Start a music application such as Windows Media Play or RealOne Player and play the music; you will listen to the stereo music from the earpiece.

c.The speaker volume of the earpiece can be adjusted by pressing the VOL + / VOL - buttons.

e.Turn the Headset off after use.

Advance functions: The following user scenarios provide you a true wireless freedom to monitor the mobile phone call status while you are enjoying stereo music at the same time. You don't even need to put down your earpiece.

*Advance functions are not supported in Sony Ericsson T610, T630

V.[ A & B ] Stereo Headset paired with Audio Adaptor and Bluetooth mobile phone Guide

Bluetooth Audio Adaptor	Bluetooth
		Bluetooth mobile phone
[ B ]	Stereo Headset
		[ A ]

1.Pairing

a.Follow the Pairing process [ B ] to pair the Headset and the Audio Adaptor.

b.After successful pairing, turn the Headset off. The Audio Adaptor will turn off automatically.

C.Follow the pairing process [ A ] to pair the Headset and the Bluetooth mobile phone.

d.After successful pairing, turn on the Audio Adaptor.

e.All three devices are in Standby Mode and the LED’s should flash green.

2.Listening to music

a.Follow the Listen to music process [ B ] to enjoy the music.

3.Monitoring mobile phone calls

a.Follow the [Advance function] in [ A ] to monitor phone calls.

VII. [ A & D ] Stereo Headset paired with

Bluetooth enabled PDA and Bluetooth mobile phone Guide

Bluetooth enabled PDA	Bluetooth	Bluetooth mobile phone
[ D ]	Stereo Headset	[ A ]
[ D ]		[ A ]

1.Pairing

a.Follow the Pairing process [ D] to pair the Headset and the Bluetooth enabled PDA.

b.After successful pairing, turn the Headset off.

c.Follow the pairing process [ A ] to pair the Headset and the Bluetooth mobile phone.

d.After successful pairing, please follow the PDA Bluetooth application program instructions to re-establish Bluetooth connection between the PDA and the Headset.

e.All three devices are in Standby Mode and the LED’s should flash green.

2.Listening to music

a.Follow the Listen to music process [ D ] to enjoy the music.

3.Monitoring mobile phone calls

a.Follow the [Advance function] in [ A ] to monitor phone calls.