Radio Shack Digital Spread Spectrum Cordless Telephone with Digital Answering System Operation

Page 13

43-3805.fm Page 13 Wednesday, May 17, 2000 3:48 PM

ˆOperation

MAKING AND

RECEIVING CALLS

To make a call, lift the handset and press TALK. The TALK/BATT indicator on the handset and the CHARGE/IN USE indicator on the base light. When you hear a dial tone, dial the number.

To answer a call, simply lift the handset. If the handset is away from the base, press any key.

To end a call, place the handset on the base or press TALK.

Note: If you press TALK to hang up and the phone does not disconnect, press TALK again while holding the handset closer to the base, or place the handset on the base.

SELECTING THE CHANNEL

The phone scans 20 channels and automati- cally selects a clear channel each time you make or receive a call.

If you hear other conversation or excessive noise during a call, press CH to select a dif- ferent channel. The TALK/BATT indicator blinks, followed by a brief pause as your phone searches for a clear channel.

Note: If the handset is too far from the base, the channel might not be clear. Move closer to the base and try making the call again.

SETTING THE

HANDSET VOLUME

You can choose one of four volume settings (low, medium, high, or maximum) for the handset. To change the volume, press VOL

8or 9 during a call.

ANSWERING CALLS USING THE SPEAKERPHONE

To answer a call using the speakerphone, press SPEAKER on the base. The SPEAKER indicator lights.

To adjust the speakerphone’s volume, re- peatedly press VOLUME 8 or 9 on the base. The volume setting from 1 (lowest) to 10 (highest) appears in the message counter window.

Note: When you press VOLUME 8 while the volume is set to the maximum or VOLUME 9 while the volume is set to the minimum, the setting does not change and the phone beeps several times.

To end a speakerphone call, press SPEAKER again.

SWITCHING BETWEEN THE HANDSET AND SPEAKERPHONE

To switch to the speakerphone while you are using the handset, press SPEAKER on the base. When you hear the conversation on the speakerphone, press TALK on the hand- set.

To switch to the handset while you are using the speakerphone, lift the handset off the base. If the handset is away from the base, press TALK, then press SPEAKER.

Operation

13

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Image 13
Contents Digital Spread Spectrum Cordless Telephone Contents Troubleshooting Read this Before InstallationFCC Statement Important Safety InstructionsFCC Wants YOU to Know LightningFm Page 5 Wednesday, May 17, 2000 348 PM Telephone Features FeaturesSave These Instructions Spread Spectrum Technology spreadsAnswering System Features Mounting the Phone InstallationOn a Desk Top On a Wall Plate or Wall Connecting Charging Battery Pack Turning the BASE’S Ringer on and OFF Setting Dialing ModeSetting the RINGER’S Tone and Volume Setting the Number of RingsSetting the DAY/TIME Quick Look AT the HandsetOperation Using Tone Services on a Pulse Line Using Both the Handset and SpeakerphoneUsing Redial Using MuteMemory Dialing Chain-Dialing Service NumbersStoring a Number in Memory Entering a PauseTesting Stored Emergency Num- bers Using a HeadsetAnswering System Operation Selecting the Outgoing MessageSetting the Answering System to Answer Calls Setting the Record TimeRECORDING/DELETING AN Outgoing Message Screening CallsRecording a Memo Adjusting the Answering SYSTEM’S VolumeRecording a Conversation Playing MessagesUsing the TOLL-SAVER Setting the Remote Operation PINUsing Remote Commands Remote OperationPhone on the same phone line Remote CommandsTroubleshooting Care Fm Page 23 Wednesday, May 17, 2000 348 PM Limited One-Year Warranty