Radio Shack 20-164 manual Fleet Maps, To program a fleet map

Page 34

Fleet Maps

For Motorola Type I and hybrid systems, you must program a fleet map before saving Talk Group IDs.

To program a fleet map:

1.Press PGM then TRUNK.

2.Press FUNC, then press  or  to select the bank.

3.If necessary, repeatedly press MODE to select “Motorola.”

4.Press FUNC, then press 8. “Size Code Setting” appears, with Block 0 selected.

5.Enter the size code for Block 0, supplied with the Type I system information, or try one of the following common fleet maps.

	Size				BLOCKS
	Codes
	Codes	0	1	2	3	4	5	6	7
		0	1	2	3	4	5	6	7

	1	S11	S11	S11	S11	S11	S11	S11	S11

	2	S4	S4	S4	S4	S4	S4	S4	S4

	3	S4	S4	S4	S4	S4	S4	S12	––

	4	S12	––	S4	S4	S4	S4	S4	S4

	5	S4	S4	S12	––	S4	S4	S4	S4

	6	S3	S10	S4	S4	S12	––	S12	––

	7	S10	S10	S11	S4	S4	S4	S4	S4

	8	S1	S1	S2	S2	S3	S3	S4	S4

	9	S4	S4	SO	SO	SO	SO	SO	SO

	10	SO	SO	SO	SO	SO	SO	S4	S4

	11	S4	SO	SO	SO	SO	SO	SO	SO

	12	SO	SO	SO	SO	SO	SO	SO	S4

	13	S3	S3	S11	S4	S4	SO	SO	SO

	14	S4	S3	S10	S4	S4	S4	S12	––

	15	S4	S4	S4	S11	S11	SO	S12	––

	16	S3	S10	S10	S11	SO	SO	S12	––

6

7

B

T t b t

(

b f

Y f

U T f

1

2

3

4

5

34

Image 34

Contents What’s Included Triple TrunkingContents Contents Volume / OFF Your ScannerAttaching the Belt Clip Connecting the AntennaTo attach the supplied antenna Powering Your Scanner BatteriesTo install batteries To charge batteriesExternal Power To use an external power sourceHeadphones and Speakers To set the keytone Keytones and KeylockBacklight and Contrast To lock the keypadTo turn on the backlight To change the backlight modeSquelch and Attenuator To change the display contrastTo set the attenuator mode To set squelchDelay Scanner SetupTo turn the delay on / off Defining a Channel To define a channelCopying a Frequency To copy a frequencyTo delete a saved frequency Deleting Saved FrequenciesTo delete all saved frequencies in a bank To define a channel’s Ctcss or DCS code Scanner CloningTo save a Ctcss or DCS code To clone the scanner data SearchingSeek Search To activate Seek SearchSearch Banks To search preprogrammed search banksZeromatic To search banks SR0-SR2To activate Zeromatic Signal StalkerProgramming a Search Range To program the search range of Bank SR7Special Signal Stalker To use Signal StalkerTo lock out a frequency To use Special Signal StalkerLocking Out Frequencies To review and unlock frequenciesTo unlock all frequencies in a search bank Saving Found FrequenciesTo save a frequency found during a search To scan ScanningLocking Out Channels To locked out a channelPriority Scanning To turn on the priority featureTo review all locked out channels To make an existing channel a Priority channel Weather AlertsTo modify the Priority channel To program a weather channel into priority channel Same Standby ModeTo perform a weather scan To program a Fips codeCode. The format of a Fips code is To review stored Fips codesTo enter Same standby SkywarnTo test the weather alert To monitor a channel MonitoringTo use Skywarn To find a frequency to monitorDefining a Trunking Bank Trunking SetupTo set a default tuning frequency To define a Trunking BankTo set Open or Closed mode for a bank Motorola Trunking SetupTrunking Modes Fleet Maps To program a fleet mapBase and Offset Frequencies For Motorola Type II, enterEdacs Trunking Setup UHF-Hi 806-960 MHz To program 800 MHz Motorola trunkingLTR Trunking Setup To save a correct Home RepeaterSaving a Talk Group ID Searching for Talk Group IDsTo search for Talk Group IDs Deleting Talk Group IDs To define a Talk Group IDTo delete a Talk Group ID Saving Trunking ChannelsTo delete ALL talk group IDs in a bank Trunk Scanning To change the scanning direction, press  or Locking Out Talk Group IDs Trunking DelayTo set a Talk Group ID delay To lock out Talk Group IDsTo turn off a sub-bank Turning Off Sub-BanksTo review locked-out Talk Group IDs To turn off a sub-bank while scanningText Tags Scanner MaintenanceTalk Group ID Hold To set Talk Group ID HoldPage Scanner is not TroubleshootingTo display the Talk Group ID Working at allScanner is on but Scanner does notReceive any stations Or reception is poor Does not scanBirdie Frequencies Initializing the Scanner Service and RepairTo initialize the scanner Scanning Legally FCC Notice Appendix a Glossary ReferencesAppendix B Search Banks Search bank SR1 CB band Receive mode AM Search bank SR2 FRS/GMRS/MURS band Search bank SR4 Aircraft Receive mode AM, FM Appendix C Ctcss / DCS Codes Ctcss CodesAll Band Appendix D Signal Stalker BandsDCS Codes PubSafety Band Motorola Appendix E Talk Group FormatTo use AFS format Appendix F Specifications 406-512 MHz 764-960 MHz9V DC Limited One-year Warranty

Related manuals

Manual 68 pages 17.08 Kb