Radio Shack 43-1302, 43-1303, 43-1301 Mounting the Phone, Using the Phone, Desktop Mounting

MOUNTING THE PHONE

Wall Mounting

(With or Without a Wall Plate)

The mounting bracket comes attached to the lower base of the phone for immediate wall mounting.

Adjust the handset holder by sliding the clip up. Then rotate it and slide it back into the slot.

To mount the phone on a

wall plate, connect the supplied short cord to the phone’s line jack and route it through the groove on the base.

To mount the phone without a wall plate, connect the sup- plied long cord. Then use two 3/16-inch (5 mm) screws (not supplied) to mount the phone on the wall.

3 15/16 Inches (100 mm)

USING THE PHONE

Lift out the memory index card and record important phone numbers.

Plug the handset cord into the jacks on the handset and base.

Press REDIAL to dial the last number dialed (up to 31 digits).

MEMORY, STORE, and M1, M2, and M3 —

See “Storing/Dialing Numbers in Memory.”

If you have pulse service, press /TONE to dial num-

	as tone signals. The
	bers *
Press to	phone returns to pulse dial-
	ing when you hang up.
disconnect
a call.	Set to TONE or PULSE
	according to the type
	of service you have.
	Set the RINGER to OFF, LOW or
	HIGHSet the.YouRINGERcan maketo OFFcalls,LOWwithor
	HIGHthe ringer.Youoff,canandmakeyoucallscan with
	receivethe ringercallsoff,ifandyou youhearcananother
	phonereceiveoncallstheifsameyou hearlineanotherringing.

Set VOLUME LOW/MED/HIGH to adjust the volume you hear through the handset.

Mounting with a Wall Plate Mounting without a Wall Plate

Desktop Mounting

To place the phone on a flat surface, remove the mounting bracket by sliding the bracket to the right and then away from the phone.

Insert the tab on the wide end of the bracket into the base’s upper left slot, and the other tab into the base’s upper right slot. Then slide the bracket to the right to snap the bracket into place.

Press FLASH for a timed switchhook signal for special services, like Call Waiting.

Note: If you do not subscribe to any special services, pressing FLASH might disconnect the call.

To make or answer a call using a headset, press HEADSET. Then (if you are making a call), dial the phone number. To end a call, press HEADSET again.

The headset indicator lights when you make and receive a call using a headset, and turns off when you end a call.

The headset jack ()lets you con- nect an optional headset, so you can step away within the cord’s reach to do another job (available from RadioShack).

To connect a headset, insert the headset’s 3/32-inch (2.5-mm) plug into .

STORING/DIALING NUMBERS IN MEMORY

Note: The phone company can charge you for the instal- lation of the necessary jacks. The USOC number of the jack to be installed is RJ11C (RJ11W for a wall jack).

CAUTION

RISK OF ELECTRIC SHOCK.

DO NOT OPEN.

This symbol is intended to alert you that parts inside the telephone present a risk of electric shock.

This symbol is intended to alert you to important operating and servicing

You can store up to 13 numbers (three priority – M1, M2, M3, and 10 standard – one for each number key).

To store a number (up to 16 digits) in memory:

1.Lift the handset. If you wear a headset, press

HEADSET. Then press STORE.

2.Enter the telephone number you want to store. Then press STORE.

3.To store a number in a priority memory, press M1, M2, or M3. For standard memories, enter the 1-digit number (0–9) for the location where you want to store the number.

4.To store more numbers, repeat Steps 1–3.

To dial a number in a priority memory:

1.Lift the handset. If you wear a headset, press

HEADSET.

2.Press the priority button (M1, M2, or M3) for the number you want to call.

To dial a number in standard memory:

1.Lift the handset.

2.Press MEMORY.

3.Enter the 1-digit location number for the number you want to call.

instructions included in the papers with the telephone.

1999 Tandy Corporation.

All Rights Reserved.

RadioShack is a registered trademark used by Tandy Corporation.