Introduction, Step One, Step Two | Radio Shack 43-3261 instruction

13-Number Memory Big Button Phone

43-3261

Introduction

Thank you for purchasing the RadioShack

13-Number Memory Big Button Phone. The ringer volume and listening volume can be adjusted using the included AC adapter and the sliding VOLUME control. Up to 10 standard phone numbers can be stored in memory, as well as three emergency numbers (fire, police, ambulance).

Handset

Coiled Handset Cord — Connects handset to base.

AC Adapter — For amplified ringer volume, connect the adapter’s barrel plug to the phone’s DC 9V jack. Connect the other end to a standard AC outlet. When the adapter is connected, the keypad lights when you lift the handset.

Base

Memory/Index Card —

Write down important numbers for quick reference. You can also write in the names and/or numbers stored in memory.

Mounting

Bracket

Long Line Cord

Short Line Cord

Step One

Attach the Mounting Bracket

1.Position the mounting bracket as shown.

2.Align the bracket tabs with the slots on the phone’s base.

3. Snap the bracket into place.

Step Two

Mount and Connect the Phone

On a Wall

Your telephone connects directly to a modular telephone line jack. If your telephone wiring does not have a modular jack, you can update the wiring yourself using jacks and adapters (available at your local RadioShack store), or have the telephone company update the wiring for you. You must use compatible modular jacks that are compliant with Part 68 of FCC Rules and the requirements adopted by the ACTA. The telephone cord and modular plug provided is Part 68 compliant for connecting to the telephone company network.

What’s Included

• Telephone Base

• Coiled Handset Cord

MEMORY — Press MEMORY, then	FLASH — Press to answer an incoming call while
press the memory location number	you are talking (if you have Call Waiting service).
to automatically dial from memory.	Press again to return to the previous call. If you do not
Or, press after entering a phone	have Call Waiting, pressing FLASH can disconnect
number to store.	the current call.
STORE — Press		REDIAL — Press to
STORE, then enter a		REDIAL — Press to
number to store in		automatically dial the last
memory. Press again		phone number you
after you enter the phone		called.
number to confirm.
LOUD — To adjust listening level,		HOLD — Press to place a call
press LOUD, and then slide VOLUME		HOLD — Press to place a call
to the desired listening level setting		on hold. HOLD lights. To
during a call. When you hang up and		resume the call, press the
make or receive another call, you must		switchhook or lift the handset.

press LOUD again before adjusting

VOLUME.

1.Drill two vertical holes 315/16 inches apart.

Base	Wall or
	Wall Plate

2.Thread a screw (not supplied) into each hole, letting the heads extend about 3/16 inch from the wall.

3.Fit the keyhole slots over the screw heads and slide the phone downward to secure it.

On a Wall Plate

•	Telephone Handset	•	Long Line Cord
•	Mounting Bracket	•	Short Line Cord
•	AC Adapter	•	Memory/Index Card

WARNING: To reduce the risk of fire or shock hazard, do not expose this product to rain or moisture.

TONE PULSE — Slide to TONE or PULSE to select the desired dialing mode (depends on you phone service). Press * during a call to switch from pulse to tone dialing.

Ring Indicator — Flashes when an incoming call is received.

LINE Jack — Connect line cord here.

Fit the keyhole slots over the wall plate studs. Slide the phone downward to secure it.

Connections

1. Connect the coiled handset cord to the jacks on

the base and the handset.


	..CAUTION..	!
	RISK OF ELECTRIC SHOCK	!
	DO NOT OPEN

The lightning symbol is intended to alert you to the presence of

uninsulated dangerous voltage within this product’s enclosure that might be of sufficient magnitude to constitute a risk of electric shock. Do not open the product’s case.

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER OR BACK. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO

QUALIFIED PERSONNEL.

The exclamation symbol is

!intended to inform you that important operating and

maintenance instructions are included in the literature accompanying this product.

DC 9V Jack — Connect adapter here for amplified ringer volume, and to activate the lighted keypad.

HI LO OFF RINGER —

Slide to the desired setting to set the ringer volume.

2.	If your phone is mounted on the wall, connect
	the long line cord to the phone’s LINE jack.
	Connect the other end to a wall jack.
3.	If your phone is mounted on a wall plate,
	connect the short line cord to the phone’s LINE
	jack. Connect the other end to a wall jack.