Polk Audio 265-LS Paint Recommendation, To paint the Sheer-Grille, Surround Speaker Placement

Important information Should YOu Choose to Paint your grilles

Because of its ultra-thin profile, the Vanishing Series Sheer-Grille™requires a specific painting procedure to ensure smooth, even coverage. The grille scrim and perforated grille come assembled and require no disassembly.

Paint Recommendation

We highly recommend you use a can of spray paint matched to the wall color you want the Sheer-Grilles to blend with.

Important Note: Never use a brush or roller to paint the grilles, as this will clog the perf holes.

To paint the Sheer-Grille

1.Elevate the Sheer-Grille off of a flat surface. This will ensure even coverage of the grille frame and make it easier to pick up.

Mounting Idea: Two spray can caps will raise the grille high enough.

2.Hold the spray paint about 12" from the grille and at a 45° angle.

3.Apply one light, thin coat, moving evenly side to side over the grille, then work your way around the perimeter of the grille

to ensure you cover the grille frame.

4.After each application of paint, wait approximately 1 minute, rotate the grille 90°, and apply the next thin coat. Important Note: You must rotate the grille

90°. Use your hands to define the next 90° rotation and always rotate the grille in the same direction of travel.

5.Three light, even applications should cover the grille and frame adequately. Remember to work your way around the grille frame to cover it evenly and completely.

Surround SPEAKER PLACEMENT

Polk Audio F/X® surround loudspeakers give you nearly endless placement options. But remember that where you place your surround speakers requires some careful thought, as installation requires that you cut a hole in your wall or ceiling.

tV

Diagram shows speaker locations for 5.1 and 7.1 systems, when two additional in-wall speakers are installed in the rear wall.

Left/Right Orientation: F/X® surround loud- speakers have a left/right orientation, and each speaker is clearly marked on the serial number label on the back of the magnet for installation on either the right or left. Right and left are defined from your listening area as you face your system’s center channel.

Center Channel Speaker Placement

Install the 255c-lsor 255c-rtas close as possible to ear level. If the speaker needs to be installed higher, aim the tweeter down as required.

Do not block the center channel with your TV or furniture.

Please Note: For more on speaker placement go

to: www.polkaudio.com/education/article.php?id=15 or www.polkaudio.com/downloads/hthandbook.pdf

Room Environment Controls

Imaging

Diffuse / Solid

Imaging (65f/x-lsmodel only)

F/X Surround Loudspeakers offer switchable “Diffuse” and “Solid” imaging patterns

to create the surround effect you desire.

A “Diffuse” image is defined as one which creates a “cloud” of sound; think of the effect as ambient sounds which fill the environment all around you, but are less localizable.

A “Solid” image is one which creates a more pin- point sound; sound is more localized. The location of sounds in the sound field is more identifiable.

Tweeter

Filter / Norm

Tweeter Switch

(LS and RT models except F/X models) Filter—If your listening room is very reflective, with smooth sheetrock walls, hardwood floors, and non-cushioned furniture, the sound will be overly “bright” and unnatural. Selecting the “Filter” setting compensates for the effect of reflectiv-

ity in a hard room. Tweeter attenuation flattens room response, without hindering higher frequency response, for warmer, more realistic sound

and more accurate imaging.

Norm—If your room is not reflective, with curtains, artwork, lots of cushioned furniture and carpeting, sound will be absorbed by the room, resulting in more realistic reproduction and more accurate imag- ing. In this case, select the tweeter “Norm” setting.

Wall Dist.

<2' >2'

(60cm) (60cm)

Wall Distance Switch (65f/x-rtand all LS Models except the Center Channel)

In-wall loudspeakers excel when placed more than 2’ (60cm) from side walls. If position limitations demand that in-wall loudspeakers be installed closer than 2’ (60cm) from side walls or ceiling, the proximity of the surface can result in a response “bump” between 50 and 200Hz. This can cause in-wall speakers to sound “boomy.” The “Wall Distance” switch flattens response and eliminates “boominess” without sacrificing deep bass response, for more lifelike sound.

For more information visit our website at www.polkaudio.com 3