GE 29297 Alarm Operation, Radio Operation, Caller ID CID, Message Indicators, Memory, Service

Page 2

Alarm Operation

The 29297 is equipped with two alarms. The alarms can be set independently to either radio or buzzer.

Setting the Alarm Time

1.Press ALARM 1 or ALARM 2.

2.Press the SET button.

3.Use the CID orbutton to set the wake time. Press and hold for 3 seconds to quickly increase or decrease the time setting in 15 minute increments.

4.Press SET to confirm.

Set alarm tone

1.Press the ALARM 1 or ALARM 2 button to review the setting.

2.Press and release the desired ALARM button to choose radio, buzzer, or off.

3.A music note icon on the display indicates that the alarm is set to radio, a bell icon indicates that the alarm is set to buzzer.

Turning Off the Alarms

To turn off an alarm, press the ALARM OFF, ALARM 1, or ALARM 2 buttons.The alarm setting is retained and comes on the next day.

Snooze Timer

After the wake mode is activated, you can silence it by pressing the snooze button.

You may use the snooze feature repeatedly.

Setting the Snooze Timer

1.Press and release the SET button.

2.Press and release the snooze button. SNOOZETIME shows in the display.

3.Press and release the CID orbutton to set the snooze time in 1 minute increments or press and hold to scroll quickly. (The default is 9 minutes.)

4.Press SET to confirm.

Using the Sleep Timer

Use the sleep timer to play the radio for a desired amount of time (increments of 15 minutes up to two hours), and then have it shut off automatically.The default sleep time is 59 minutes.

1.Press the SLEEP button repeatedly to select the desired sleep timer setting. Each press of the button will decrease the setting by 15 minutes.

2.The radio turns on automatically and the timer starts after you’ve selected the desired setting.

NOTE: To review the current sleep timer setting, press and release SLEEP.

3.To cancel the sleep timer and turn the radio off, press snooze or

RADIO ON/OFF.

Radio Operation

1.Press and release the RADIO ON/OFF button to turn the radio on.

2.Press the AM/FM button to the select the desired broadcast band.

3.Rotate the tuning knob to select a radio station / frequency.

4.Rotate the volume control wheel to adjust the listening level.

5.To turn the radio off, press and release RADIO ON/OFF.

NOTE: You can also turn on the radio after lifting up the handset by pressing the RADIO ON/OFF button.

Built-in AFC

The built-in Automatic Frequency Control (AFC) works only on FM mode. It helps keep the radio locked onto the FM stations/frequencies.

FM stereo is a built in function.

AM Antenna

A built-in antenna eliminates the need for an outside antenna for AM reception. Moving the unit slightly may improve reception of distant AM signals.

FM Antenna

The power cord acts as your FM antenna.The power cord picks up moderate to strong signals and eliminates the need for an external antenna in most strong signal areas. Be sure the power cord is stretched to its longest length. Do not coil or bunch the cord together. Changing position of the power cord may improve reception.

Caller ID (CID)

Caller ID (CID) is a service available from your local telephone company. For Caller ID to work on this system, you must subscribe to Caller ID service.

This unit receives and displays information transmitted by your local phone company and can store up to 70 calls for later review.

VERY IMPORTANT: The Caller ID feature of this product requires a subscription to Caller ID service from your telephone company.

Summary Screen

The summary screen (display) shows the current time, current date and number of new calls to be reviewed. It is displayed until any button is pressed. Within 60 seconds of receiving a new call, the summary screen is displayed and the NEW CALL indicator comes on.

NOTE: Check with your local phone company regarding name service availability.

Receiving and Storing CID Records

When you receive a call, the information is transmitted by the phone company to your Caller ID telephone between the first and second ring. When memory is full, a new call automatically replaces the oldest call in memory. NEW appears in the display for calls received that have not been reviewed.

Reviewing CID Records

As calls are received and stored, the display is updated to let you know how many calls have been received.

Press the CID orbutton to scroll through the call records.

After all of the records are viewed, START/END appears in the display.

Deleting CID Records

To delete the record showing in the display, press the DELETE button once.

To delete all records (while reviewing), press and hold the DELETE button. DELETE ALL? appears in the display. Press DELETE again to confirm.

Dialing Back

When reviewing CID records, you may dialback the number showing in the display by pressing the DIAL button.

If you programmed your local area code in the set up menu

1.Use the CID orbutton to display the number you want to dial.

If you see a number with 7 digits (i.e. 555-1234), then the call was received from within your area code. However, this does not guarantee the call is a local call.

If you see a number with 11 digits (i.e. 1-234-555-1234), then the call received was not from your area code.

2.Press the DIAL button and the display shows PICKUP/ADJ.You have 10 seconds to adjust the number and pick up the handset to dial, otherwise the unit returns to the currently reviewed call.

3.To adjust the phone number, press the DIAL button. Press the DIAL button repeatedly to scroll through the 7, 10, and 11-digit numbers.

7-digits: 7-digit telephone number (i.e. 555-5555)

10-digits:3-digit area code + 7-digit telephone number (i.e. 425-555-5555)

11-digits:long distance code 1 + 3-digit area code + 7-digit telephone number (i.e. 1-425-555-5555)

4.To dial the displayed number, pick up the handset within 10 seconds. NOW DIALING shows in the display and the number is dialed.

If you did not program your local area code in the set up menu

1.Use the CID orbutton to display the number you want to dial.

2.See steps 2 through 4 in the above section to complete the dialback sequence.

NOTE: If the CID record has a 7-digit or 10-digit number, adjusting only adds “1” digit to the dialed number. Press the DIAL button repeatedly to scroll through the 11,10,7 digit sequence, otherwise no adjustment may be made and the number is dialed as received.

Message Indicators

The following messages show the status of the phone, provide Caller ID information, or help you set up and use your phone.

NO CALLS

Indicates there is no record in memory.

UNKNOWN

The incoming call is from an area not

CALLER

serviced by CID or CID information is not sent.

BLOCKED CALL

Caller information is blocked from transmission.

ERROR

Caller information has been interrupted

 

 

 

 

during transmission.

NO DATA

Caller information is interrupted during

 

 

 

 

transmission or the phone is excessively noisy.

START/END

Indicates you are at the beginning or the end of the

 

 

 

 

call record log.

 

 

 

 

Battery power is low.

Memory

The following buttons can be used as memory locations for storing data: 0-9 keys and memory buttons A, B, or C.

Storing a Number in Memory

1.Pick up the handset.

2.Press STORE.

3.Enter the telephone number, up to 16 digits (the phone number will not be dialed in this mode).

4.Press STORE.

5.Press the desired memory location button (0-9 or A, B, or C.)

6.Hang up the handset.

NOTE: If you make a mistake, hang up the handset and repeat the procedure for storing a number from the beginning.

Changing a Stored Number

Repeat the storage sequence in the Storing a Number in Memory section.The new number replaces the old number in the memory location.

NOTE: When the unit is first powered up, unwanted digits may be randomly created in memory locations. See Erasing a Stored Number to delete unwanted digits.

Erasing a Stored Number

1.Pick up the handset.

2.Press STORE.

3.Press REDIAL.

4.Press STORE again.

5.Press the location (A, B, C, 0-9) to be erased.

Dialing a Number Stored in One-Touch Memory Location A, B or C

1.Pick up the handset.

2.Press the memory location button A, B, or C.The number in that memory location dials automatically.

Dialing Stored Numbers

1.Pick up the handset.

2.Press MEMORY.

3.Press memory location 0-9.The number dials automatically.

Inserting a Pause in the Dialing Sequence

The REDIAL button becomes a pause function when the STORE button is pressed first. It is valid only when storing numbers into memory locations.

Use the REDIAL button to insert a pause when a delay is needed in an automatic dialing sequence. For example, when you must dial a

9 to get an outside line or when you enter codes to access your long distance company.

Chain Dialing from Memory

Use this feature to make calls which require a sequence of numbers, for instance if you use a calling card for a frequently called long distance number. Each part of the sequence is dialed from memory.The following example shows how you can use chain dialing to make a call through a long distance service:

The Number For

Memory Location

Long distance access number

7

Authorization code

8

Frequently called long distance number

9

1.Pick up the handset.

2.Press the MEMORY button and then press 7.

3.When you hear the access tone, press MEMORY and then press 8.

4.At the next access tone, press MEMORY and then 9.

Troubleshooting Tips

Telephone Solutions

No DialTone

Check all cabling to make sure that all connections are secure and not damaged.

Check the hook switch: It should fully extend from the base when the handset is lifted from the cradle?

Phone Does Not Ring

Make sure the ringer is turned on.

There may be too may extension phones connected to your line. Try disconnecting an extension phone.

See solution for ”NO DIALTONE. ”

Incoming and Outgoing Voice Volume Low

Are other phones off hook at same time? If so, this is normal condition as volume drops when additional phones are used at once.

Caller ID Solutions

No Information is Shown After the Phone Rings

To receive CID data, you must subscribe to Caller ID service from your telephone company.

Wait until the second ring before answering. CID data is received after the 1st ring.

Error Message is Displayed

ERROR appears in the display if the unit detects anything other than valid Caller ID information during the silent period after the first ring.This message indicates either the presence of noise on the line, or that an invalid message has been sent from the telephone company.

Wait until the second ring before answering.

General Product Care

To keep your unit working and looking good, follow these guidelines:

Avoid putting it near heating appliances and devices that generate electrical noise (for example, motors or fluorescent lamps).

DO NOT expose to direct sunlight or moisture.

Avoid dropping answerer and/or other rough treatment.

Clean with a soft cloth.

Never use a strong cleaning agent or abrasive powder because this will damage the finish.

Retain the original packaging in case you need to ship it at a later date.

Service

If trouble is experienced with this equipment, for repair or warranty information, please contact customer service at 1-800-448-0329. If the equipment is causing harm to the telephone network, the telephone company may request that you disconnect the equipment until the problem is resolved.

This product may be serviced only by the manufacturer or its authorized service agents. Changes or modifications not expressly approved by ATLINKS USA, Inc. could void the user’s authority to operate this product. For instructions on how to obtain service, refer to the warranty included in this guide or call customer service at 1- 800-448-0329.

Or refer inquiries to: ATLINKS USA, Inc.

Manager, Consumer Relations P O Box 1976 Indianapolis, IN 46206

Attach your sales receipt to the booklet for future reference or jot down the date this product was purchased or received as a gift.This information will be valuable if service should be required during the warranty period.

Purchase date ___________________________________________

Name of store ___________________________________________

Limited Warranty

What your warranty covers:

Defects in materials or workmanship.

For how long after your purchase:

One year, from date of purchase.

(The warranty period for rental units begins with the first rental or 45 days from date of shipment to the rental firm, whichever comes first.)

What we will do:

Provide you with a new or, at our option, a refurbished unit.The exchange unit is under warranty for the remainder of the original product’s warranty period.

How you get service:

Properly pack your unit. Include any cables, etc., which were originally provided with the product. We recommend using the original carton and packing materials.

”Proof of purchase in the form of a bill of sale or receipted invoice which is evidence that the product is within the warranty period, must be presented to obtain warranty service.” For rental firms, proof of first rental is also required. Also print your name and address and a description of the defect. Send via standard UPS or its equivalent to:

ATLINKS USA, Inc. c/o Thomson

11721 B Alameda Ave. Socorro,Texas 79927

Pay any charges billed to you by the Exchange Center for service not covered by the warranty.

Insure your shipment for loss or damage. ATLINKS accepts no liability in case of damage or loss.

A new or refurbished unit will be shipped to you freight prepaid.

What your warranty does not cover:

Customer instruction. (Your Owner’s Manual provides information regarding operating instructions and user controls. Any additional information, should be obtained from your dealer.)

Installation and setup service adjustments.

Batteries.

Damage from misuse or neglect.

Products which have been modified or incorporated into other products.

Products purchased or serviced outside the USA.

Acts of nature, such as but not limited to lightning damage.

Product Registration:

Please complete and mail the Product Registration Card packed with your unit. It will make it easier to contact you should it ever be necessary.The return of the card is not required for warranty coverage.

Limitation of Warranty:

THE WARRANTY STATED ABOVE ISTHE ONLY WARRANTY APPLICABLE TOTHIS PRODUCT. ALL OTHER WARRANTIES, EXPRESS OR IMPLIED (INCLUDING ALL IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE) ARE HEREBY DISCLAIMED. NO VERBAL OR WRITTEN INFORMATION GIVEN BY ATLINKS USA, INC., ITS AGENTS, OR EMPLOYEES SHALL CREATE A GUARANTY OR IN ANY WAY INCREASETHE SCOPE OFTHIS WARRANTY.

REPAIR OR REPLACEMENT AS PROVIDED UNDERTHIS WARRANTY ISTHE EXCLUSIVE REMEDY OFTHE CONSUMER. ATLINKS USA, INC. SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROMTHE USE OFTHIS PRODUCT OR ARISING OUT OF ANY BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ONTHIS PRODUCT. THIS DISCLAIMER OF WARRANTIES AND LIMITED WARRANTY ARE GOVERNED BYTHE LAWS OFTHE STATE OF INDIANA. EXCEPTTOTHE EXTENT PROHIBITED BY APPLICABLE LAW, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ONTHIS PRODUCT IS LIMITEDTOTHE APPLICABLE WARRANTY PERIOD SET FORTH ABOVE.

How state law relates to this warranty:

Some states do not allow the exclusion nor limitation of incidental or consequential damages, or limitations on how long an implied warranty lasts so the above limitations or exclusions may not apply to you.

This warranty gives you specific legal rights, and you also may have other rights that vary from state to state.

If you purchased your product outside the USA:

This warranty does not apply. Contact your dealer for warranty information.

Image 2
Contents No Worry Battery Backup Important Installation InformationInstalling the Phone Set UpTroubleshooting Tips Alarm OperationMessage Indicators Service

29297 specifications

The GE 29297 is an innovative and highly regarded product from General Electric, known for its reliability and state-of-the-art features. Designed for industrial applications, the GE 29297 offers advanced technology that enhances performance while ensuring operational efficiency.

One of the main features of the GE 29297 is its robust build quality. Constructed with durable materials, it is designed to withstand harsh environmental conditions, making it suitable for various industrial settings. The unit is engineered for high performance, boasting a powerful motor that can handle demanding tasks with ease.

Incorporating cutting-edge technology, the GE 29297 includes digital controls and advanced monitoring systems. This allows for precise adjustments and real-time performance tracking, ensuring optimal operation at all times. The unit is equipped with smart sensors that monitor vital parameters, providing valuable data that can help in preemptive maintenance and troubleshooting.

Energy efficiency is another hallmark of the GE 29297. The device is designed to minimize energy consumption without compromising on performance. This not only contributes to cost savings for businesses but also aligns with global sustainability initiatives. The integration of energy-saving technologies helps reduce the overall carbon footprint of operations.

Additionally, the GE 29297 features versatile compatibility with various industrial systems and machinery. Its design allows for easy integration into existing workflows, making it an ideal choice for companies looking to upgrade their equipment without major overhauls. The intuitive interface simplifies operation, allowing personnel of varying skill levels to use it effectively.

Safety is prioritized in the design of the GE 29297. With built-in protective mechanisms and compliance with industry standards, the device ensures a safe working environment. Features such as overload protection, temperature monitoring, and emergency shut-off systems are included to safeguard both the equipment and the personnel.

Overall, the GE 29297 stands out as a versatile and powerful solution for industrial applications. With its combination of robust construction, advanced technology, energy efficiency, and user-friendly design, it is well-suited to meet the needs of modern industries, providing reliability and performance that businesses can count on.