•Avoid dropping the product or treating it roughly.
•Clean with a soft cloth.
•DO NOT immerse the parent unit and the baby unit in water and do not clean them under the tap.
•DO NOT use cleaning spray or liquid cleaners.
•Make sure the baby unit and parent unit are dry before you connect them to the mains again.
Storage
When you are not going to use the baby monitor for some time, remove the rechargeable battery from the parent unit. Store the parent unit, the baby unit and the adapters in a cool and dry place.
Frequently asked questions
Below are the questions most frequently asked about the baby monitor. If you cannot find the answer to your question, contact customer service by visiting our
website at www.vtechphones.com or calling 1 (800) 595-9511.
Why does the | Try the following (in the order |
baby monitor not | listed) for common cure: |
respond normally? | 1. Disconnect the power to |
| the baby units and the |
| parent unit. |
| 2. Remove the batteries in the |
| parent unit. Then install the |
| batteries again. |
| 3. Wait a few minutes before |
| connecting power back |
| to the baby units and the |
| parent unit. |
| 4. Turn on the baby units and |
| the parent unit. |
| 5. Wait for the parent unit |
| to synchronize with the |
| baby units. Allow up to one |
| minute for this to take place. |
Why don’t the | Perhaps the rechargeable |
power-on light of | battery of the parent unit is |
the baby unit and | empty and the parent unit is |
parent unit go on | not connected to the mains. |
when I switch on | Insert the appliance plug |
the units? | into the parent unit and put |
| the adapter in a wall socket. |
| Then press to switch on the |
| parent unit and to establish |
| connection with the baby unit. |
| |
| Perhaps the baby unit is |
| not connected to the mains. |
| Connect the baby unit to the |
| mains. Then set ON/OFF |
| switch to ON to switch on the |
| baby unit and to establish |
| connection with the parent unit. |
| |
| Why is my screen | The screen is in black and |
| in black and | white when the infrared LEDs |
| white? | are on during nighttime or in a |
| | dark room. This is normal due |
| | to external light sources. |
| | |
| Why does the | The units may be too close |
| baby monitor | to each other. Make sure the |
| produce a high- | parent unit and the baby unit |
| pitched noise? | at least 1 metre/3 feet away |
| | from each other. |
| | |
| Why does the | The baby unit also picks up |
| parent unit react | other sounds than those |
| too quickly to | of your baby. Adjust the |
| other sounds? | sensitivity level to a lower |
| | level or adjust the speaker |
| | volume on the parent unit. |
| | |
| Why don’t I hear a | The volume of the parent unit |
| sound/Why can’t | may have set too low. Press |
| I hear my baby | /VOL+ to increase the |
| cry? | volume level. |
| | You may have set a low |
| | sound sensitivity level. See |
| | Adjust the sound sensitivity |
| | of the baby unit to change |
| | the setting. |
| Why does the | The baby units may be out of |
| parent unit beep? | range. Move the parent unit |
| | closer to the baby units (but |
| | not less than 3 feet). |
| | |
| | If the parent unit is powered by |
| | the provided battery, it may not |
| | have enough charge for the |
| | parent unit to perform normally. |
| | Charge the battery in the |
| | parent unit for up to 12 hours. |
| | |
| Why can’t I | The baby units may be out of |
| establish a | range. Move the parent unit |
| connection? Why | closer to the baby units (but |
| is the connection | not less than 3 feet). |
| lost every now | |
| Other electronic products may |
| and then? Why |
| cause interference with your |
| are there sound |
| baby monitor. Try installing |
| interruptions? |
| your baby monitor as far away |
| |
| | from these electronic devices |
| | as possible. |
| | |
Important safety instructions
When using your equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury, including the following:
1.Follow all warnings and instructions marked on the product.
2.Adult setup is required.
3.This product is intended as an aid. It is not a substitute for responsible and proper adult supervision and should not be used as such.
4.This product is not intended for use as a medical monitor.
5.Do not use this product near water. For example, do not use it next to a bath tub, wash bowl, kitchen sink, laundry tub or swimming pool, or in a wet basement or shower.
6.CAUTION: Use only the batteries indicated in this manual. There may be a risk of explosion if a wrong type of battery is used for the parent unit. Use only the supplied rechargeable battery or replacement battery pack (BT185645/BT285645) for the parent unit. Do not dispose of batteries in a fire. They may explode. Dispose of used battery according to the information in The RBRC® seal.
7.Use only the adapters included with this product. Incorrect adapter polarity or voltage can seriously damage the product.
Baby unit power adapter: Input 100-240V
AC 150mA 50/60Hz; Output: 6V DC 600mA
Parent unit power adapter: Input 100-240V
AC 150mA 50/60Hz; Output: 6V DC 600mA.
8.The power adapters are intended to be correctly oriented in a vertical or floor mount position. The prongs are not designed to hold the plug in place if it is plugged into a ceiling, under-the-table or cabinet outlet.
9.Unplug this product from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning.
10.Unplug the power cords before replacing batteries.
11.Do not cut off the power adapters to replace them with other plugs, as this causes a hazardous situation.
12.Do not allow anything to rest on the power cords. Do not install this product where the
cords may be walked on or crimped.
13.This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply in your home, consult your dealer or local power company.
14.Do not overload wall outlets or use an extension cord.
15.Do not place this product on an unstable table, shelf, stand or other unstable surfaces.
16.This product should not be placed in any area where proper ventilation is not provided. Slots and openings in the back or bottom of this product are provided for ventilation. To protect them from overheating, these openings must not be blocked by placing the product on a soft surface such as a bed, sofa or rug. This product should never be placed near or over a radiator or heat register.
17.Never push objects of any kind into this product through the slots because they may touch dangerous voltage points or create a short circuit. Never spill liquid of any kind on the product.
18.To reduce the risk of electric shock, do not disassemble this product, but take it to an authorized service facility. Opening or removing parts of the product other than specified access doors may expose you to dangerous voltages or other risks. Incorrect reassembling can cause electric shock when the product is subsequently used.
19.You should test the sound reception every time you turn on the units or move one of the components.
20.Periodically examine all components for damage.
21.Be aware of possible loss of privacy while using public airwaves. Conversations may be picked up by other nursery monitors, cordless phones, scanners, etc.
22.Children should be supervised to ensure
that they do not play with the product.
23.The product is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
SAVE THESE INSTRUCTIONS
Cautions
1.Use and store the product at a temperature between 32oF and 104oF.
2.Do not expose the product to extreme cold, heat or direct sunlight. Do not put the product close to a heating source.
3.Batteries should not be exposed to excessive heat such as bright sunshine or fire.
4.Make sure the baby unit(s) and the adapter cord(s) are always out of reach of the baby, at least 3 feet away from the baby or crib, to avoid a possible strangulation hazard.
5.Never place the baby unit(s) inside the baby’s crib or playpen. Never cover the baby unit(s) or parent unit with anything such as a towel or a blanket.
6.Other electronic products may cause interference with your baby monitor. Try installing your baby monitor as far away from these electronic devices as possible: wireless routers, radios, cellular telephones, intercoms, room monitors, televisions, personal computers, kitchen appliances and cordless telephones.
Precautions for users of implanted cardiac pacemakers
Cardiac pacemakers (applies only to digital cordless devices):
Wireless Technology Research, LLC (WTR), an independent research entity, led a multidisciplinary evaluation of the interference between portable wireless devices and implanted cardiac pacemakers. Supported by the U.S. Food and Drug Administration, WTR recommends to physicians that:
Pacemaker patients
•Should keep wireless devices at least six inches from the pacemaker.
•Should NOT place wireless devices directly over the pacemaker, such as in a breast pocket, when it is turned ON.
WTR’s evaluation did not identify any risk to bystanders with pacemakers from other persons using wireless devices.
Electromagnetic fields (EMF)
This VTech product complies with all standards regarding electromagnetic fields (EMF).
If handled properly and according to the instructions in this user’s manual, the product is safe to be used based on scientific evidence available today.
The RBRC® seal
The RBRC® seal on the nickel-metal battery indicates that VTech Communications, Inc. is voluntarily participating in an industry program to collect and recycle these batteries at the end of their useful lives, when taken out of service within the United States and Canada.
The RBRC® program provides a convenient alternative to placing used nickel-metal batteries into the trash or municipal waste, which may be illegal in your area.
VTech’s participation in RBRC® makes it easy for you to drop off the spent battery at local retailers participating in the RBRC® program or at authorized VTech product service centers. Please call
1 (800) 8 BATTERYTM for information on Ni-MH battery recycling and disposal bans/restrictions in your area. VTech’s involvement in this program is part of its commitment to protecting our environment and conserving natural resources.
RBRC® is a registered trademark of Rechargeable Battery Recycling Corporation.
FCC and IC regulations
FCC Part 15
This equipment has been tested and found to comply with the requirements for a Class B digital device under Part 15 of the Federal Communications Commission (FCC) rules. These requirements are intended to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications to this equipment not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
(1)this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
To ensure safety of users, the FCC has established criteria for the amount of radio frequency energy that can be safely absorbed by a user or bystander according to the intended usage of the product. This product has been tested and found to comply with the FCC criteria. The baby unit shall be installed and used such that parts of all persons’ body are maintained at a distance of approximately
8 in (20 cm) or more.
This Class B digital apparatus complies with Canadian requirement:
CAN ICES-3 (B)/NMB-3(B)
Industry Canada
This device complies with Industry Canada licence- exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and
(2)this device must accept any interference received, including interference that may cause undesired operation.
Privacy of communications may not be ensured when using this product.
The term ‘’IC:‘’ before the certification/registration number only signifies that the Industry Canada technical specifications were met.
This product meets the applicable Industry Canada technical specifications.
RF radiation exposure statement
The baby unit complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. The baby unit should be installed and operated with a minimum distance of 8 in (20 cm) between the baby unit and all persons’ body. Use of other accessories may not ensure compliance with FCC RF exposure guidelines. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment complies also with Industry Canada RSS-102 with respect to Canada’s Health Code 6 for Exposure of Humans to RF Fields.
California Energy Commission battery charging testing mode
This baby monitor meets the California Energy Commission (CEC) regulations for energy consumption. Your baby monitor is set up to comply with the energy-conserving standards right out of the box.
Follow the instructions to install and charge the battery. The CEC battery charging testing mode is activated while charging.
Even if the parent unit is paired to baby units, the CEC battery charging testing mode is activated while it is powered off and charging.
For cETL compliance only
Mesures de sécurité importantes
Lorsque vous utilisez votre appareil, vous devriez toujours suivre certaines mesures de précaution de base afin de réduire les risques d’incendie, d’électrocution et de blessures corporelles, dont ceux qui suivent :
1. | Observez toutes les instructions et mises en |
| garde inscrites sur l’appareil. |
2. | L’installation par un adulte est requise. |
3. | Ce produit a été conçu pour être un dispositif |
| d’appoint seulement. Il n’est pas le remplacement |
| d’une supervision responsable et adéquate par un |
| adulte et ne devrait pas être utilisé comme telle. |
4. | Ce produit n’est pas conçu pour être utilisé en |
| tant que moniteur médical. |
5. | N’utilisez pas cet appareil près de l’eau ni de toute |
| autre source d’humidité, par exemple, près d’une |
| baignoire, cuve à lessive, évier de cuisine, dans |
| un sous-sol humide ni près d’une piscine, dans un |
| soussol humide ou une douche. |
6. | MISE EN GARDE: Il peut y avoir un risque |
| d’explosion si vous utilisez le mauvais type de |
| piles pour l’unité du parent. N’utilisez que le |
| bloc-piles rechargeable inclus ou le bloc-piles de |
| rechange (BT185645/BT285645). N’incinérez pas |
| les piles. Celles-ci risqueraient d’exploser. Jetez |
| les piles usées selon les renseignements suivant |
| le sceau du RBRC®. |
7. | N’utilisez que les adaptateurs inclus avec ce |
| produit. L’utilisation d’un adaptateur dont la |
| polarité ou la tension serait inadéquate risque |
| d’endommager sérieusement le produit et mettre |
| votre sécurité en péril. |
| Adaptateur de l’unité du bébé : |
| Entrée 100-240V CA 150mA 50/60 Hz; |
| Sortie : 6 V CC 600 mA |
verticale ou au plancher. Les broches n’ont pas été conçues pour supporter le poids du bloc d’alimentation et le maintenir en place si celuici est branché dans une prise au plafond, sous une table ou dans un meuble.
9. | Débranchez ce produit de la prise de courant |
| avant de procéder au nettoyage. N’utilisez pas de |
| nettoyants en aérosols. Utilisez un chiffon humide |
| pour le nettoyer. |
10. | Débranchez les cordons d’alimentation avant de |
| remplacer le bloc-piles. |
11. | Ne coupez pas les cordons d’alimentation pour |
| remplacer les fiches, car ceci peut présenter un |
| danger potentiel. |
12. | Ne laissez aucun objet reposer ni appuyer sur |
| le cordon d’alimentation. N’installez pas cet |
| appareil dans un endroit où l’on risque d’écraser |
| le cordon d’alimentation ou de le piétiner. |
13. | Ne faites fonctionner cet appareil qu’avec le |
| type d’alimentation indiqué sur l’étiquette. Si |
| vous ne connaissez pas le type d’alimentation |
| que vous possédez à votre domicile, consultez |
| votre marchand ou votre compagnie locale |
| d’électricité. |
14. | Ne surchargez pas les prises de courant murales |
| ni les rallonges électriques. |
15. | Ne placez pas cet appareil sur un chariot, |
| meuble, trépied, support de montage ni table |
| chancelants. |
16. | Les trous et ouvertures du boîtier, situés à |
| l’arrière de l’appareil ou sous celui-ci, servent à |
| aérer l’appareil. Pour l’empêcher de surchauffer, |
| ne bloquez sous aucun prétexte ces ouvertures |
| et n’empêchez pas l’aération adéquate de |
| l’appareil en le plaçant sur un lit, divan, tapis ou |
| toute autre surface similaire. De même, ne le |
| positionnez pas à proximité ni au-dessus d’une |
| source de chaleur ou d’un calorifère. De plus, |
| ne placez pas l’appareil dans un endroit avant |
| de vous assurer qu’il y ait une bonne circulation |
| d’air. |
17. | N’enfoncez jamais d’objets à travers les |
| ouvertures de cet appareil, car ils pourraient |
| entrer en contact avec des points de tension |
| dangereux ou causer des courts-circuits qui |
| peuvent dégénérer en incendies ou en risques |
| d’électrocution. Ne renversez jamais de liquide |
| dans ce produit. |
18. | Afin de réduire les risques d’électrocution, ne |
| démontez pas cet appareil, mais apportez-le |
| dans un centre de service autorisé. L’ouverture |
| du boîtier ou le retrait de toutes pièces que |
| contient cet appareil, à l’exception de l’accès |
| autorisé à certaines portes ou ouvertures, |
| risque de vous exposer à des points de tension |
| dangereux ou d’autres dangers. Un remontage |
| incorrect peut par la suite présenter des risques |
| d’électrocution. |
lorsque vous utilisez les ondes publiques. Les conversations peuvent être entendues par d’autres moniteurs de bébé, des téléphones sans fil, des scanneurs, etc.
22.Les enfants devraient être supervisés afin de vous assurer qu’ils ne jouent pas avec l’appareil.
23.Le produit n’est pas conçu pour être utilisé par des personnes (incluant des enfants) aux capacités physiques, sensorielles ou mentales réduites ou qui manquent d’expérience et de connaissances, à moins qu’on leur ait donné suffisamment de supervision ou d’instructions relativement à l’utilisation de l’appareil par une personne responsable de leur sécurité.
CONSERVEZ CES INSTRUCTIONS
Mises en garde
1.Utilisez et entreposez le produit à une température entre 0˚ C (32˚F) et 40˚C (104˚ F).
2.N’exposez pas cet appareil à des froids ou des chaleurs extrêmes, ainsi qu’à la lumière directe du soleil. Ne l’installez pas près d’une source de chauffage.
3.Le bloc-piles ne doit pas être exposé à la chaleur excessive telle que la lumière du soleil ou au feu.
4.Assurez-vous que le moniteur et le cordon de l’adaptateur sont toujours hors de portée des enfants, à au moins 1 mètre (3 pieds) de l’enfant ou du berceau, pour éviter tout risque de strangulation.
5.Ne jamais placer le moniteur à l’intérieur du berceau ou du parc de bébé. Ne jamais couvrir le moniteur ou l’unité (s) portative avec un article tel une serviette ou une couverture.
6.D’autres équipements électroniques peuvent produire des interférences sur votre moniteur vidéo et audio. Tentez d’installer votre moniteur vidéo ou audio à l’écart des appareils électroniques tels que des routeurs sans fil, radios, téléphones cellulaires, interphones, moniteurs, téléphones, ordinateurs personnels, électroménagers et téléphones sans fil.
Stimulateurs cardiaques implantés dans l’organisme
Les simulateurs cardiaques (ne s’applique qu’aux dispositifs numériques sans fil) :
L’organisme ‘Wireless Technology Research, LLC (WTR)’, une firme de recherche indépendante,
a mené une évaluation pluridisciplinaire des interférences entre les téléphones sans fil portatifs et les stimulateurs cardiaques implantés dans l’organisme. Appuyée par l’Administration des aliments et drogues (FDA) des États-Unis, la firme WTR recommande aux médecins:
Avis aux détenteurs de stimulateurs cardiaques
L’étude effectuée par l’organisme WRS n’a pas identifié de risque pour les détenteurs de simulateurs cardiaques causés par les gens qui utilisent dispositifs sans fil à proximité de ceux-ci.
Champs électromagnétiques (EMF)
Ce produit de VTech est conforme à toutes les normes se rapportant aux champs électromagnétiques (EMF) standard. Si vous le manipulez correctement en suivant les instructions de ce guide, son utilisation sera sécuritaire pendant de nombreuses années, selon les meilleures évidences scientifiques dont nous disposons aujourd’hui.
Limited warranty
What does this limited warranty cover?
The manufacturer of this VTech Product warrants to the holder of a valid proof of purchase (“Consumer” or “you”) that the Product and all accessories provided in the sales package (“Product”) are
free from defects in material and workmanship, pursuant to the following terms and conditions, when installed and used normally and in accordance with the Product operating instructions. This limited warranty extends only to the Consumer for Products purchased and used in the United States of America and Canada.
What will VTech do if the Product is not free from defects in materials and workmanship during the limited warranty period (“Materially Defective Product”)?
During the limited warranty period, VTech’s authorized service representative will repair or replace at VTech’s option, without charge, a Materially Defective Product. If we repair the Product, we may use new or refurbished replacement
parts. If we choose to replace the Product, we may replace it with a new or refurbished Product of the same or similar design. We will retain defective parts, modules, or equipment. Repair or replacement of the Product, at VTech’s option, is your exclusive remedy. VTech will return the repaired or replacement Products to you in working condition. You should expect the repair or replacement to take approximately 30 days.
How long is the limited warranty period?
The limited warranty period for the Product extends for ONE (1) YEAR from the date of purchase. If VTech repairs or replaces a Materially Defective Product under the terms of this limited warranty, this limited
What is not covered by this limited warranty?
This limited warranty does not cover:
1.Product that has been subjected to misuse, accident, shipping or other physical damage, improper installation, abnormal operation or handling, neglect, inundation, fire, water or other liquid intrusion; or
2.Product that has been damaged due to repair, alteration or modification by anyone other than an authorized service representative of VTech; or
3.Product to the extent that the problem experienced is caused by signal conditions, network reliability, or cable or antenna systems; or
4.Product to the extent that the problem is caused by use with non-VTech accessories; or
5.Product whose warranty/quality stickers, product serial number plates or electronic serial numbers have been removed, altered or rendered illegible; or
6.Product purchased, used, serviced, or shipped for repair from outside the United States of America or Canada, or used for commercial or institutional purposes (including but not limited to Products used for rental purposes); or
7.Product returned without a valid proof of purchase (see item 2 on the next page); or
8.Charges for installation or set up, adjustment of customer controls, and installation or repair of systems outside the unit.
How do you get warranty service?
NOTE: Before calling for service, please review the user’s manual - a check of the Product’s controls and features may save you a service call.
Except as provided by applicable law, you assume the risk of loss or damage during transit and transportation and are responsible for delivery or handling charges incurred in the transport of the Product(s) to the service location. VTech will return repaired or replaced Product under this limited warranty. Transportation, delivery or handling charges are prepaid. VTech assumes no risk for damage or loss of the Product in transit. If the Product failure is not covered by this limited warranty, or proof of purchase does not meet the terms of this limited warranty, VTech will notify you and will request that you authorize the cost of repair prior
to any further repair activity. You must pay for the cost of repair and return shipping costs for the repair of Products that are not covered by this limited warranty.
What must you return with the Product to get warranty service?
1. Return the entire original package and |
3.Provide your name, complete and correct mailing address, and telephone number.
Other limitations
This warranty is the complete and exclusive agreement between you and VTech. It supersedes all other written or oral communications related to this Product. VTech provides no other warranties for this Product. The warranty exclusively describes all of VTech’s responsibilities regarding the Product. There are no other express warranties. No one
is authorized to make modifications to this limited warranty and you should not rely on any such modification.
State/Provincial Law Rights: This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state or province to province.
Limitations: Implied warranties, including those of fitness for a particular purpose and merchantability (an unwritten warranty that the Product is fit for ordinary use) are limited to one year from the date of purchase. Some states/provinces do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. In no event shall VTech be liable for any indirect, special, incidental, consequential, or similar damages (including, but not limited to lost profits or revenue, inability to use the Product or other associated equipment, the cost of substitute equipment, and claims by third parties) resulting from the use of this Product. Some states/provinces do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.
Please retain your original sales receipt as proof of purchase.
Technical specifications
Frequency | Crystal controlled PLL synthesizer |
control | |
| |
Transmit | Baby unit: 2407.5 - 2475 MHz |
frequency | Parent unit: 2407.5 - 2475 MHz |
|
| |
Channels | 21 |
| |
LCD | 2” Color LCD |
| (QVGA 320x240 pixel) |
| |
Nominal | Maximum power allowed by FCC |
effective | and IC. Actual operating range may |
range | vary according to environmental |
| conditions at the time of use. |
| |
Power | Parent unit: 3.6 V Ni-MH battery |
requirement | Baby unit power adapter: |
|
| Input: 100-240V AC 150mA 50/60Hz |
| Output: 6V DC 600mA |
| Parent unit power adapter: |
| Input: 100-240V AC 150mA 50/60Hz |
| Output: 6V DC 600mA |
| |
