VTech VT 9114 important safety instructions Important Safety Instructions, Introduction

Page 1

91-005435-020-000

IMPORTANT SAFETY INSTRUCTIONS

When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury, including the following:

1. Read and understand all instructions.

2. Follow all warnings and instructions marked on the product.

3. Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.

4. Do not use this product near water (for example, near a bath tub, kitchen sink, or swimming pool).

5. Do not place this product on an unstable cart, stand, or table. The product may fall, causing serious damage to the product.

6. Slots and openings in the cabinet and the back or bottom are provided for ventilation. To protect it from overheating, these openings must not be blocked by placing the product on the bed, sofa, rug, or other similar surface. This product should never be placed near or over a radiator or heat register. This product should not be placed in a built-in- installation where proper ventilation is not provided.

7. This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your dealer or local power company.

8. Do not allow anything to rest on the power cord. Do not locate this product where the cord will be abused by persons walking on it.

9. Never push objects of any kind into this product through cabinet slots, as they may touch dangerous voltage points or short out parts that could result in a risk of fire or electric shock. Never spill liquid of any kind on the product.

10.To reduce the risk of electric shock, do not disassemble this product. If service or repair work is required, contact VTech Customer Service at 1-800-595-9511. Opening or removing cabinet parts other than specified access doors may expose you to dangerous voltages or other risks. Incorrect reassembling can cause electric shock when the appliance is subsequently used.

11.Do not overload wall outlets and extension cords as this can result in the risk of fire or electric shock.

12.Unplug this product from the wall outlet:

a)When the power supply cord or plug is damaged or frayed.

b)If liquid has been spilled into the product.

c)If the product has been exposed to rain or water.

d)If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions, because improper adjustment of other controls may result in damage and will often require extensive work to restore the product to normal operation.

e)If the product has been dropped and the cabinet has been damaged.

f)If the product exhibits a distinct change in performance.

13.Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning.

14. Do not use the telephone to report a gas leak in the vicinity of the leak.

SAVE THESE INSTRUCTIONS

2

INTRODUCTION

Parts Check List:

To purchase replacement battery

1.

Handset

packs, call VTECH Communications

2.

Base Unit

at 1-800-595-9511. In Canada, call

3.

Telephone Line Cord

VTECH Electronics at 1-800-267-

4.

Battery Pack

7377.

5.

AC Adapter

 

1

INSTALLING/REPLACING THE BATTERY PACK

1. Slide the battery cover off by gently pressing on the recessed area with a downward motion.

2. Unplug and remove the old battery pack. Don't put the old battery pack in a trash compactor or a fire - it could burst.

3. With the red and black wires at the bottom of the pack, angle the top of the battery into the compartment, under the two “claws”. Next, press the lower end of the battery pack down, so it is held in place by the lower claw. Now, plug the connector into the socket, located below the battery. Slip the battery wires into the wire guide, located below and to the left of the socket.

4. Replace the battery cover by sliding it into place.

5.The new battery pack must be charged before using your telephone. Place the handset in the cradle of the base unit to allow it to charge for 16 hours. Maximum battery life between charges is more than 3.75 hours of

continuous talk time or 3.75 days of standby.

CAUTION: To reduce the risk of fire or injury, read and follow these instructions:

1.Use only VTECH battery pack supplied, or equivalent..

2.Do not open or mutilate the battery. Released electrolyte is corrosive and may cause damage to the eyes or skin. It may be toxic if swallowed.

3.Exercise care in handling batteries in order not to short the battery with conducting materials such as rings, bracelets, and keys. The battery or conductor may overheat and cause burns.

4.Do not dispose of the battery in a fire. The cell may explode.

The RBRC™ Seal

The RBRC® Seal on the nickel-cadmium battery indicates that VTech Communications, Inc. is voluntarily participating in an industry program to collect and recycle these batteries at the end of their useful lives, when taken out of service within the United States and Canada.

The RBRC® program provides a convenient alternative to placing used nickel- cadmium batteries into the trash or municipal waste, which may be illegal in your area.

VTech’s participation with RBRC® makes it easy for you to drop off the spent battery at local retailers participating in the RBRC® program or at authorized VTech product service centers. Please call 1-800-8-BATTERY™ for information on Ni-Cd battery recycling and disposal bans / restrictions in your area. VTech’s

involvement in this program is part of its commitment to protecting our environment and conserving natural resources.

RBRC ® is a registered trademark of Rechargeable Battery Recycling Corporation.

3

GETTING STARTED

Setting Up Your VT9114

1.Choose an area near an electrical outlet and a telephone wall jack.

2.Plug the AC power adapter into an electrical outlet and the AC connector to the power jack on the bottom of the Base Unit. Insert the cord in the channel guide.

CAUTION: Use only the AC adapter shipped with your VT9114. It is specifically designed for this product.

NOTE: Connect power to the Base Unit before placing the handset in the

HANDSET FEATURES

 

REDIAL / PAUSE KEY

 

 

• When you hear the dial tone,

 

press REDIAL to call the last

 

number dialed on your phone.

 

• It can also be used to store the

 

last number dialed into the speed

 

dial memory. See Storing a

 

Redial Number into Speed Dial

 

for details.

 

 

 

• You can store pauses into your

 

speed dial numbers. See Storing

 

Pauses in Memory for details.

ON LED

CHAN KEY

 

 

• The ON LED lights when the

• Pressing the CHAN key when the

Handset is on an active call.

Handset is in use will activate a

• It flashes in cadence with an

channel change to the next free

incoming ring.

channel.

 

 

• It flashes quickly during

• This is used

if you

are

Programming mode.

experiencing

noise

or

• It flashes slowly when the battery

interference on

the current

pack is low.

channel.

 

 

cradle.

3.CHARGE THE HANDSET BATTERY PACK BEFORE USE. The batteries recharge automatically whenever the Handset is in the Base Unit cradle. The batteries must be charged for 16 hours before using your phone for the first time.

4.Connect the telephone line cord. Insert one end of the telephone line cord into the phone jack on the bottom of the Base Unit. Plug the other end into a telephone wall jack. Make sure the plugs snap securely into place. Insert the cord in the channel guide.

5.CHECK FOR A DIAL TONE. After the battery pack is charged, pick up the Handset and press the ON key. The IN USE LED on the Base and ON LED on the Handset should light up, and you should hear a dial tone. If not, see

IN CASE OF DIFFICULTY.

CAUTION:

1.

Never install telephone wiring during a lightning storm.

2.

Never install telephone jacks in wet locations unless the jack is specifically

 

designed for wet locations.

ON/ FLASH KEY

•Press the ON key to make a call.

•If you are currently on a call, and you hear a call waiting tone, press ON to switch to the second call. Press ON again to return to

the original call.

VOLUME CONTROL

•Adjust the volume of what you hear through the Handset.

•While on a call, press the or

key to adjust the listening volume. The Handset will emit a double beep when the maximum or minimum volume level has been reached.

MEM/PROG KEY

•Press the MEM key to enter

MEMORY mode.

•The sequence for dialing out a speed dial number in memory is: ON, MEM, Number Button (0-9).

•Press MEM/PROG to enter programming mode. See

Programming Speed Dial

Numbers for more details.

TONE/ * KEY

•In PULSE dialing mode, this key is used to switch to Temporary TONE dialing mode.

3.

Never touch uninsulated telephone wires or terminals unless the telephone

 

line has been disconnected at the network interface.

4.

Use caution when installing or modifying telephone lines.

OFF KEY

•Press the OFF key to exit all modes of operation.

4

5

Page 1 Page 2
Image 1
Page 1 Page 2
Contents Handset Features Important Safety InstructionsIntroduction Getting StartedOperating Instructions Base Unit FeaturesCase of Difficulty USE/CHARGING LEDMaintenance Warranty StatementPower Requirements Repair instructions Programming/testing of emergency numbersRights of the telephone company Hearing aid compatibility

VT 9114 specifications

The VTech VT 9114 is a sophisticated yet user-friendly cordless phone designed for both home and office use. This device stands out in the crowded telecommunications market thanks to its unique blend of cutting-edge technology and practical features. One of the primary features of the VT 9114 is its DECT 6.0 technology, which provides enhanced clarity and a more secure connection. This technology reduces interference from other wireless devices, ensuring that conversations remain clear and uninterrupted.

The phone boasts a sleek and ergonomic design, making it not only aesthetically pleasing but also comfortable to hold during long conversations. The large, backlit display is easy to read, even in low-light conditions, allowing users to quickly access their contacts and call logs. Speaking of contacts, the VTech VT 9114 stores up to 100 names and numbers, making it simple for users to stay connected with family, friends, and colleagues.

Another notable feature is the speakerphone function, which allows for hands-free communication. This is particularly beneficial during multi-tasking or when several people need to join in on a conversation. Additionally, the phone has a built-in intercom system, making it easy to communicate between handsets within the same home or office setup.

The VT 9114 also incorporates an advanced caller ID system, displaying the name and number of incoming calls, allowing users to screen their calls efficiently. Another valuable characteristic is the phone's ability to block unwanted calls, helping to reduce telemarketer interruptions and enhance user privacy.

Energy efficiency is another aspect worth mentioning. The VTech VT 9114 is designed to consume less power than traditional cordless phones, contributing to lower energy bills and a smaller carbon footprint. With a long battery life, users can enjoy extended talk time without the frequent need for recharging.

In conclusion, the VTech VT 9114 combines advanced technology with practical features that cater to the needs of both individual users and small businesses. Its intuitive design, user-friendly interface, and range of useful functionalities position it as an ideal choice for anyone in need of a reliable cordless phone. With its blend of efficiency and sophistication, the VT 9114 is designed to facilitate seamless communication in the modern digital age.
Top Page Image Contents