Motorola MR350TPR, MR351 technical specifications Safety and General Information, Getting Started

Page 1

®

Two-Way Radio

User’s Guide

KEM-PK14190-90MR350/351

For More Information

For further information, you may call Motorola at 1-800-638-5119 (U.S. and Canada), or e-mail us at giantintl@callcenter.com or visit us on the Internet at www.motorola.com.

Safety and General Information

Important Information on Safe and Efficient Operation

Read This Information Before Using Your Radio.

The information provided in this document supersedes the general safety information in user guides published prior to December 1, 2002.

Transmit and Receive Procedure

Your two-way radio contains a transmitter and a receiver. To control your exposure and ensure compliance with the general population/ uncontrolled environment exposure limits, always adhere to the following procedure:

Transmit no more than 50% of the time.

To receive calls, release the PTT button.

To transmit (talk), press the Push to Talk (PTT) button.

Transmitting 50% of the time, or less, is important because the radio generates measurable RF energy exposure only when transmitting (in terms of measuring standards compliance).

Exposure to Radio Frequency Energy

Your Motorola two-way radio complies with the following RF energy exposure standards and guidelines:

United States Federal Communications Commission, Code of Federal Regulations; 47CFR part 2 sub-part J.

American National Standards Institute (ANSI)/Institute of Electrical and Electronic Engineers (IEEE) C95. 1-1992.

Institute of Electrical and Electronics Engineers (IEEE) C95.

1-1999 Edition.

International Commission on Non-Ionizing Radiation Protection (ICNIRP) 1998.

Ministry of Health (Canada) Safety Code 6. Limits of Human Exposure to Radiofrequency Electromagnetic Fields in the Frequency Range from 3 KHz to 300 GHz, 1999.

Australian Communications Authority Radiocommunications (Electromagnetic Radiation—Human Exposure) Standard, 2003.

ANATEL ANNEX to Resolution No. 303 of July 2, 2002 “Regulation of limitation of exposure to electrical, magnetic and electromagnetic fields in the radio frequency range between 9 KHz and 300GHz”.

To ensure optimal radio performance and make sure human exposure to radio frequency electromagnetic energy is within the guidelines set forth in the above standards, always adhere to the following procedures.

Portable Radio Operation and EME Exposure

Antenna Care

Use only the supplied or an approved replacement antenna. Unauthorized antennas, modifications, or attachments could damage the radio and may violate FCC regulations.

Do NOT hold the antenna when the radio is “IN USE.” Holding the antenna affects its effective range.

Body-Worn Operation

To maintain compliances with FCC/Health Canada RF exposure guidelines if you wear a radio on your body when transmitting always place the radio in a Motorola-supplied or approved clip holder, holster, case or body harness for this product. Use of non-Motorola-approved accessories may exceed FCC/Health Canada RF exposure guidelines.

If you do not use one of the Motorola-supplied or approved body-worn accessories and are not using the radio held in the normal use position,

ensure the radio and its antenna are at least 1 inch (2.5 cm) from your body when transmitting.

Data Operation

If applicable, when using any data feature of the radio with or without an

accessory cable, position the radio and its antenna at least one inch (2.5 cm) from the body.

Approved Accessories

For a list of approved Motorola accessories, visit our Web site at www.motorola.com.

Electromagnetic Interference/Compatibility

Note: Nearly every electronic device is susceptible to electromagnetic interference (EMI) if inadequately shielded, designed or otherwise configured for electromagnetic compatibility. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1.This device may not cause harmful interference; and

2.This device must accept any interference received, including interference that may cause undesired operation.

IC Canada

The term "IC:" before the equipment certification number only signifies that the Industry Canada technical specifications were met.

Facilities

To avoid electromagnetic interference and/or compatibility conflicts, turn off your radio in any facility where posted notices instruct you to do so. Hospitals or health care facilities may be using equipment that is sensitive to external RF energy.

Aircraft

When instructed to do so, turn off your radio when onboard an aircraft. Any use of a radio must be in accordance with applicable regulations per airline crew instructions.

Medical Devices – Pacemakers

The Advanced Medical Technology Association recommends that a minimum separation of 6 inches (15 cm) be maintained between a handheld wireless radio and a pacemaker. These recommendations are consistent with the independent research by and recommendations of the U.S. Food and Drug Administration.

People with pacemakers should:

ALWAYS keep the radio more than 6 inches (15 cm) from their pacemaker when the radio is turned ON.

Not carry the radio in the breast pocket.

Use the ear opposite the pacemaker to minimize the potential for interference.

Turn the radio OFF immediately if there is any reason to suspect that interference is taking place.

Medical Devices – Hearing Aids

Some digital wireless radios may interfere with some hearing aids. In the event of such interference, you may want to consult your hearing aid manufacturer to discuss alternatives.

Medical Devices – Other

If you use any other personal medical device, consult the manufacturer of your device to determine if it is adequately shielded from RF energy. Your physician may be able to assist you in obtaining this information.

Safety and General Use While Driving

Check the laws and regulations regarding the use of radios in the area where you drive, and always obey them. If you do use your radio while driving, please:

Give full attention to driving and to the road.

Use hands-free operation, if available.

Pull off the road and park before making or answering a call if driving conditions so require.

The use of a two-way radio while engaged in activities requiring concentration may cause distraction or otherwise impair your ability to safely participate in such activities. Always use technology safely.

Do not place a portable radio in the area over an air bag or in the air bag deployment area. Air bags inflate with great force. If a portable radio is placed in the air bag deployment area and the air bag inflates, the radio may be propelled with great force and cause serious injury to occupants of the vehicle.

Potentially Explosive Atmospheres

Turn off your radio prior to entering any area with a potentially explosive atmosphere. Only radio types that are especially qualified should be used in such areas as “Intrinsically Safe.” Do not remove, install or charge batteries in such areas. Sparks in a potentially explosive atmosphere can cause an explosion or fire resulting in bodily injury or even death.

Note: The areas with potentially explosive atmospheres referred to above include fueling areas such as below decks on boats, fuel or chemical transfer or storage facilities, areas where the air contains chemicals or particles (such as grain, dust or metal powders) and any other area where you would normally be advised to turn off your vehicle engine. Areas with potentially explosive atmospheres are often—but not always—posted.

Blasting Caps and Areas

To avoid possible interference with blasting operations, turn off your radio when you are near electrical blasting caps, in a blasting area, or in areas posted “Turn off two-way radios.” Obey all signs and instructions.

Operational Cautions

Antennas

Do not use any portable radio that has a damaged antenna. If a damaged antenna comes into contact with your skin, a minor burn can result.

Batteries

All batteries can cause property damage and/or bodily injury such as burns if a conductive material—like jewelry, keys or beaded chains— touch exposed terminals. The conductive material may complete an electrical circuit (short circuit) and become quite hot. Exercise care in handling any charged battery, particularly when placing it inside a pocket, purse or other container with metal objects.

Exercise care when removing NiMH or AA batteries. Do not use sharp or conductive tools to remove either of these batteries.

Battery Charger Safety Instructions:

Save these Instructions

1.Do not expose the charger to rain or snow.

2.Do not operate or disassemble the charger if it has received a sharp blow, or has been dropped or damaged in any way.

3.Never alter the AC cord or plug provided with the unit. If the plug will not fit the outlet, have the proper outlet installed by a qualified electrician. An improper condition can result in a risk of electric shock.

4.To reduce the risk of damage to the cord or plug, pull the plug rather than the cord when disconnecting the charger from the AC receptacle.

5.To reduce the risk of electric shock, unplug the charger from the outlet before attempting any maintenance or cleaning.

6.Use of an attachment not recommended or sold by Motorola may result in a risk of fire, electric shock or personal injury.

7.Make sure the cord is located so it will not be stepped on, tripped over or subjected to damage or stress.

8.An extension cord should not be used unless absolutely necessary. Use of an improper extension cord could result in a risk of a fire and/or electric shock. If an extension cord must be used, make sure that:

The pins on the plug of the extension cord are the same number, size and shape as those on the plug of the charger.

The extension cord is properly wired and in good condition.

The extension cord size is 18 AWG for lengths up to 100 feet, and 16 AWG for lengths up to 150 feet.

9.The supply cord of the AC adaptor cannot be replaced. If the cord is damaged, call customer service at 1-800-638-5119 (U.S. and Canada) or e-mail us at giantintl@callcenter.com.

FCC Licensing Information

Your Motorola radio operates on General Mobile Radio Service (GMRS) frequencies and is subject to the Rules and Regulations of the Federal Communications Commission (FCC). The FCC requires that all operators using GMRS frequencies obtain a radio license before operating their equipment. To obtain the FCC forms, please visit the FCC’s Web site at wireless.fcc.gov/uls/index.htm?job=home to source form 605 and 159, which includes all the instructions you will need.

If you wish to have the document faxed or mailed, or if you have questions, please use the following contact information:

For a fax:

For mail service:

If you have

Contact the

Call the FCC

questions about

Fax-0n-Demand

Forms Hotline

the FCC License:

system

 

Call the FCC

 

 

 

1-202-418-0177

1-800-418-FORM

1-888-CALL-FCC

 

(3676)

(225-5322)

Changes or modifications not expressly approved by Motorola may void the user’s authority granted by the FCC to operate this radio and should not be made. To comply with FCC requirements, transmitter adjustments should be made only by or under the supervision of a person certified as technically qualified to perform transmitter maintenance and repairs in the private land mobile and fixed services as certified by an organization representative of the user of those services. Replacement of any transmitter component (crystal, semiconductor, etc.) not authorized by the FCC equipment authorization for this radio could violate FCC rules.

 

Control Buttons

Volume

 

 

Emergency Alert

Push to Talk

LED Indicator

(High)

 

Push to Talk

Accessory Jack

(Low)

 

Microphone

Flashlight Button

Call Tone

Scan/Monitor

 

 

Menu/Lock

Scroll/Weather

 

Mini-USB

Flashlight LED

Charging Port

Display Screen Guide

Numbers for Channel,

Call Tone

Numbers for Codes

— Battery Meter

— Scan

— Channel Power

— Vibrate

Indicator

— Call Tone,

(see Menu Options)

— Lock

Keypad Tone

— Weather Alert

— Talk Confirmation

Hands-Free Use

Tone (Roger Beep)

— Noise Filtering

Without

Accessories

— On/Off for each

Hands-Free Use

feature

With Accessories

Getting Started

Installing the Batteries

Each radio can use either 1 NiMH rechargeable battery pack or 3 AA alkaline batteries and beeps when the batteries are low.

Installing NiMH Rechargeable Battery Pack (Optional Accessory)

1.Turn the radio off.

2.With the back of the radio facing you, lift the battery cover latch up and remove the cover.

3.Remove the NiMH battery pack from the clear plastic bag (do not disassemble or unwrap the battery pack).

4.Insert the NiMH battery pack with the diagram facing you. (The ribbon should be underneath the battery pack and should wrap around the right side of the pack for easy removal.)

5.Reposition the battery cover and press down to secure.

Installing the Three AA Alkaline Batteries

1.Turn the radio off.

2.With the back of the radio facing you, lift the battery cover latch up and remove the cover.

3.Insert the three AA alkaline batteries with + and - polarity as shown inside. (The ribbon should be underneath the AA alkaline batteries and should wrap around the right side of the batteries.)

4.Reposition the battery cover and press down to secure.

Radio Battery Meter

 

The radio battery icon shows the battery charge level, from full

to

empty

. When the radio has one segment left, the

 

radio chirps periodically or after releasing (Low Battery Alert).

Removing the NiMH Battery Pack (Optional Accessory)

1.Turn the radio off.

2.With the back of the radio facing you, lift the battery latch up to release the battery cover and remove the cover.

3.Remove the NiMH battery pack by pulling the ribbon attached to the radio.

4.Reposition the battery cover and press down to secure.

Removing the Three AA Alkaline Batteries

1.Turn the radio off.

2.With the back of the radio facing you, lift the battery latch up to release the battery cover and remove the cover.

3.Gently remove each alkaline battery by easing each battery out individually.

4.Reposition the battery cover and press down to secure.

Notes

Exercise care when removing NiMH or AA batteries. Do not use sharp or conductive tools to remove either of these batteries.

Remove the batteries before storing your radio for extended periods of time. Batteries corrode over time and may cause permanent damage to your radio.

Using the Battery Charger (Optional Accessory)

The battery charger provides drop-in charging convenience for NiMH batteries and can be placed on any flat surface, such as a desk or workbench. Charge the NiMH battery overnight (at least 16 hours) before using it for the first time. After the initial charge, an empty battery is fully charged within 14 hours.

1.Follow the steps above to install a NiMH Battery Pack.

2.Plug the AC power supply cord into the jack on the desk stand.

3.Plug the AC power supply into a standard wall outlet.

4.With a radio facing forward, slide it into one of the charging pockets.

5.When charging in the battery charger, the red light on the charger base will glow continuously.

Using the mini-USB Charging Connector

The mini-USB charging connector is a handy port that allows you to conveniently charge your NiMH battery pack. This is an alternative to charging your NiMH battery pack in the Battery Charger desk stand using the AC wall adaptor and especially useful when used while traveling.

Available mini-USB charging options (Optional Accessories):

1.Wall travel charger

2.Vehicle charger

3.Mini-USB computer cable

If using a computer, the computer must be turned on.

This and other accessories (sold separately) are available for your radio. For more information, visit our Web site at www.motorola.com or shop.giantintl.com.

1.Plug your mini-USB cable or charger into a power source as is appropriate for your accessory.

2.Plug the cable into the mini-USB port on the bottom of your radio.

3.An empty battery will be fully charged in 14 hours.

4.The LED indicator light on the radio will glow to indicate that the battery is charging.

Notes

The light will remain red after the NiMH battery pack is fully charged.

When moving between hot and cold temperatures, do not charge the NiMH battery pack until the battery temperature acclimates (usually about 20 minutes).

For optimal battery life, remove the radio from the charger within 16 hours. Do not store the radio while connected to the charger.

If the radio is kept on while charging, the charging time will be extended.

Even though the charger is connected, you may not be able to

transmit a message if the battery is completely empty . Allow

time for the battery to charge to 1 bar

before attempting to

transmit a message.

 

Attaching and Removing the Belt Clip

1.Attach belt clip to pocket or belt strap.

2.Align the belt clip post with the hole in the back of the radio.

3.Gently push until the clip clicks in place.

To Remove

1.Push down on the release tab at the top of the belt clip to release the catch.

2.Pull the belt clip away from the back of the radio.

Turning your Radio On and Off

Turn clockwise to turn the radio on and counterclockwise to turn the radio off.

1.In the ON position, the radio chirps and briefly shows all feature icons available on the radio.

2.The display screen then shows the current channel, code and all features that are enabled.

Setting the Volume

 

 

Press and hold

for three seconds while rotating

until you reach a

comfortable listening level.

 

1.Rotate clockwise to increase the volume.

2.Rotate counterclockwise to decrease the volume.

Do not hold the radio close to your ear. If the volume is set to an uncomfortable level, it could hurt your ear.

Talking and Listening

To communicate, all radios in your group must be set to the same channel and Interference Eliminator Code.

1.To talk, press and hold .

2.When you are finished talking, release .

For maximum clarity, hold the radio two to three inches away from your mouth and speak directly into the microphone. Do not cover the microphone while talking.

Talk Range

Your radio is designed to maximize performance and improve transmission range. Do not use the radios closer than five feet apart.

Power Boost

To boost your radio’s power up to high power, press the top portion of the

button when talking. If you know your party is close by, you can conserve your battery’s energy by pushing the lower part of the button to use less power.

Note: If you are on an FRS only channel (see Channels and Frequencies table) the radio will only use low power when either portion of the is pressed.

Monitor Button

Pressing and holding for three seconds allows you to listen to the volume level of the radio when you are not receiving. This allows you to adjust the volume, if necessary. You can also press to check for activity on the current channel before you talk.

Push to Talk Timeout Timer

To prevent accidental transmissions and save battery life, the radio emits a continuous warning tone and stops transmitting if you press for 60 continuous seconds.

Menu Options

Selecting the Channel

Your radio has 22 channels. The channel is the frequency the radio uses to transmit. Channels 8-14 are FRS 0.5 watt only and all other channels are GMRS. (See the "Channels and Frequencies" table on overleaf for details.)

1. With the radio on, press . When the radio is on a 0.5

watt channel,

displays. When the radio is on a 1.5 watts

channel,

displays. The current channel flashes.

2.Press or and select an unused or quiet channel.

3.Press to save the channel setting or to continue set up.

Selecting the Interference Eliminator Code

Interference Eliminator Codes help minimize interference by blocking transmissions from unknown sources. Your radio has 121 Interference Eliminator Codes. Codes 1 – 38 are the standard analog codes that appear on other FRS/GMRS radios. Codes 39 – 121 are additional digital codes added for superior interference protection. 0 is the off position, no analog or digital codes are enabled.

To set the code for a channel:

1.Press until the code starts to flash.

2.Press or to select the code.

3.Press to save the code setting or to continue set up.

You can set a different code for each channel using this procedure. An extended press of or allows you to scroll through the Interference Code rapidly so you can quickly reach the code you want.

Note: You must set the Interference Eliminator Code to 0 on a radio that uses Interference Eliminator Codes to communicate with radios that do not have Interference Eliminator Codes. Select 0 for “no tone, no code” and OFF will flash on your radio’s display.

Setting and Transmitting Call Tones

Your radio can transmit different call tones to other radios in your group so you can alert them that you want to talk. Your radio has 20 call tones from which to choose.

To set a call tone:

1.Press three times until the current call tone setting flashes and

appears.

2.Press or to change and hear the call tone.

3.Press to set the new call tone or to continue set up.

To transmit your call tone to other radios set to the same channel and Interference Eliminator Code as your radio, press .

Note: Setting the call to 0 disables the call tone feature.

Hands-Free Use Without Accessories (

)

You can use the iVOX feature to transmit hands-free without the need for any headset accessories. Once iVOX is turned on, the radio detects your voice and transmits when you speak into the internal microphone.

1. Press

until

appears on the display. The current setting

On/Off will flash.

 

2.Press or to select On or Off.

3.Press to set or to continue set up.

Continued on back

MR350/351

Image 1
Contents FCC Licensing Information Safety and General InformationGetting Started Talking and ListeningWarranty Special FeaturesChannels and Frequencies Weather Receiver
Related manuals
Manual 5 pages 16.75 Kb

MR351, MR350, MR350R, MR350TPR, KEM-PK14190-90 specifications

The Motorola KEM-PK14190-90 is a sophisticated communication tool designed for individuals and teams that demand reliable and efficient connectivity in various environments. This device is part of a family that includes models such as the MR350TPR, MR350R, MR350, and MR351. Each model brings unique features and capabilities tailored to meet diverse communication needs.

The MR350 series, for instance, is known for its rugged build and robust design, making it ideal for outdoor and challenging conditions. These walkie-talkies feature a range of up to 35 miles, which makes them perfect for hiking, camping, and other outdoor activities. The long-range capability is complemented by 22 channels and 121 privacy codes, allowing users to communicate without interference from nearby radio users.

One of the standout features of the MR350 is its built-in NOAA weather radio, which provides important weather alerts and updates. This feature is especially valuable for outdoor enthusiasts who need to stay informed about changing weather conditions. Additionally, the devices in this range come equipped with advanced noise cancellation technology, ensuring clear communication even in loud environments.

Battery performance is another critical characteristic of the Motorola KEM-PK14190-90 family. With a combination of rechargeable batteries and standard AA alkaline options, users can stay connected for extended periods without the worry of running out of power. The battery-saving features extend usage time, making these models suitable for long trips or busy workdays.

In terms of ease of use, the MR350 series offers an intuitive interface with large buttons and a clear display, making it straightforward for users to operate. Furthermore, these devices provide the option of hands-free communication through voice activation, allowing for seamless interaction while multitasking.

Durability is a hallmark of the Motorola line, and the MR350 series is no exception. These devices are built to meet IP54 standards for water and dust resistance, ensuring they can withstand various environmental challenges.

Overall, the Motorola KEM-PK14190-90, along with its MR350 counterparts, stands out as a powerful communication solution. With features like long-range capabilities, weather alerts, advanced noise cancellation, and a rugged design, they are well-suited for both recreational and professional use. Whether for adventure in the great outdoors or communication in demanding work environments, these devices deliver reliability and performance that users can depend on.