WIRELESS HEADSET
Owner’s Manual
Model: EM529
In the box
WIRELESS HEADSET
Owner’s Manual
Model: EM529
Owner’s
Manual
Bluetooth
Headset
S M L |
|
Silicone cushions | USB charging |
| cable |
AC charger
Earhook
Car Charger
Drive Safe
CAUTION: Although this device enables drivers to conduct handsfree conversations, it is still safer to pull over before using a mobile phone.
Always keep your full attention on your driving.
Driving while talking on your mobile phone is dangerous, and illegal in many states.
Check local laws regarding the use of a mobile handset and wireless headset while driving. If you use the Bluetooth Headset while driving, ensure your attention and focus remains on your driving.
Please use your mobile phone, and our
product responsibly while driving!
Location of controls
Power Switch
Power ON/OFF
(Green = ON, Red = OFF)
Noise cancel | Speaker/ |
Silicone cushion | |
microphone 1 |
|
Call button |
|
Answer/end a call | Volume Up |
Indicator |
|
light | Volume Down |
Charging |
|
socket | Microphone |
| |
Noise cancel |
|
microphone 2 |
|
Charging the headset
NOTE: Charge the headset for at least 8 hours beforeusing it for the rst time, even if the RED LED indicator shuts o.
1.Connect the small end of the USB cable to the charging socket of the headset.
2.Connect the other end of the USB cable to either the:
•AC Charger, and plug into a wall (A/C) outlet
•Computer’s USB port
•Car Charger
3.The RED LED indicator light turns on while the headset is charging.
4.The RED LED indicator light shuts o when the headset is fully charged (approximately
NOTE: When the battery is running low, the RED LED indicator
light starts to ash along with a warning beep.
USB cable
Indicator
light
Charging
Socket
Headset
AC Charger | PC | Car Charger |
About noise cancellation technology
This headset uses a dual microphone design to lter out wind and unwanted external noise.
Using Noise Cancellation Technology, the headset compares the sound from the twin
Noise cancel microphone 1
Noise cancel microphone 2
Noise Cancellation Technology
Enables the other end of your conversation to hear you clearly!
Pairing the headset
Easy Pairing
(First time pairing only)
Please read through this section before turning the device on. We recommend reading this manual in it’s entirety before pairing the headset for the rst time.
This Bluetooth headset has an “Easy Pairing” feature which sets the headset to Pairing Mode the rst time the power switch is turned on.
1.Make sure the Bluetooth Headset is within 3 feet of our mobile phone or Bluetooth enabled device.
within 3 feet
Indicator light 
Red and Blue ashing
Power Switch
Power ON/OFF
(Green = ON, Red = OFF)
2.Set the [Power] switch to the ON position. The indicator light should be ashing RED and BLUE alternately, indicating the headset is in Pairing Mode and ready to connect to your Bluetooth enabled device.
3.Continue to“Manual Pairing” step 5 shown in the next column.
NOTE: Manual Pairing
If the rst time pairing was unsuccessful or for future pairing, you will need to manually pair the headset to your Bluetooth enabled device (see“Manual Pairing” step 1 in the next column ).
Manual Pairing
1.Make sure the Bluetooth Headset is within 3 feet of your mobile phone or Bluetooth enabled device.
2.Set the [Power] switch to the ON position.
3.Press and HOLD the [Call] button until the indicator light ashes RED and BLUE alternately.
4.The headset is now in Pairing Mode and is ready to connect to your mobile phone or Bluetooth enabled device.
Power Switch
Power ON/OFF
(Green = ON, Red = OFF)
within 3 feet
Indicator light 
Red and Blue ashing
NOTE: To enter Pairing Mode at any time, you must press and HOLD the [Call] button for approximately 10 seconds.
Continue here from “Easy Pairing”
5. Set your mobile phone to search for Bluetooth devices.
Bluetooth:
Enabled
Paired Devices:
*Empty *
Searching for devices
1found Stop
6.When the phone nds the headset, conrm by selecting EM529 from the list.
Bluetooth:
Enabled
Paired Devices:
EM529
Select Device:
EM529
Cancel
7. Enter the passcode “0000” when prompted by the phone.
Bluetooth:
Enabled
Paired Devices:
EM529
Enter numeric passkey for EM529:
0000
OK
OR depending on which model mobile phone you are trying to connect the headset to, it may not be necessary to enter a passcode and the following message (or similar) may appear on your phone’s display.
Bluetooth:
Enabled
Paired Devices:
EM529
“EM529” would like to pair with your phone. Would you like to allow it to pair?
Cancel Pair
Select “Pair” to complete the pairing process.
8.Your mobile phone will conrm that the pairing process was completed and prompt you to accept the connection. Please select “YES” to connect the headset to your mobile phone. If the pairing was successful, the headset’s blue indicator light turns to standby mode and ashes once every three seconds.
Bluetooth:
Enabled
Paired Devices:
EM529
Confirm connection to
EM529?
YES / NO
9.When attempting to reconnect the headset to your mobile phone, you may see the message below and your mobile phone will prompt you to accept the connection request to the EM529 headset, and an option not to ask this again. Please accept the connection, and if you select“Don’t ask this again”, your phone will automatically accept future connection requests from the headset.
Bluetooth:
Enabled
Paired Devices:
EM529
Accept connection request from EM529?
YES / NO
Don’t ask this again
NOTE: The screenshots above are typical of many Bluetooth enabled phones in the market today, and are used to assist in the explanation of the pairing process. Your mobile phone’s or Bluetooth enabled device’s interface and interaction with the headset may be slightly dierent from the illustrations shown.